Grand AM :: 2.4 Rough Idle When Engine Warms Up
2001 Grand am 2.4. Runs fine when the engine is cold but when it warms up the idle is rough. When throttle is added from idle, RPM's drop, it hesitates, then either stalls or goes. Car runs just fine when there is a load on the engine (highway speeds). Sometimes it will even stall coming onto off ramps off the freeway. It intermittently shifts hard. SES light is on p0108. Have replaced the MAP sensor and checked for vacuum leaks, still have the light and the same problems.
View 7 RepliesGrand AM :: 2000 SE Rough Idle And Sounds Like It Might Die
I have a 2000 pontiac grand am with a 2.4 L engine it is automatic transmission. Th issue is i just bought the car from a lot thinking it was an easy fix. What happens is when i start the car it goes from a 1k idle to a 500 or lower and sounds like it might die or if i am at a stop light and decelerate too fast it also feels like its going to die and has a few times unless i keep the gas pedal pressed down. I read the codes at my local store they said it was a engine misfire, o2 sensor the front one, and the map sensor.
My farther works at a pull and save which is a lot to pull used parts from cars hes brought a used ignition coil, used boots , i bought new spark plugs and nothing was fixed there. we have replaced the maf sensor and the map sensor both with used parts neither fixed the problem. I am at my wits end here i cannot afford to take it to the shops around here and am trying to get this fixed to get back and forth to work. I may have left out parts that have been replaced, also as far as lights are concerned the check engine soon light is on .
Grand AM :: 2000 V6 SE - Rough Idle And Stalls / Gears Not Shifting When Car In Motion
My grand am has a gnarly idle issue. It stalls to turn on and once on it has a very rough idle. When I put the car into drive it stales then just turns off. Drained the heck out of my battery so I was thinking it was an alternator issue but I did a quick test and my alternator seems to be working fine. I did manage to drive my car but once in motion, gears wouldn't shift which has me leading to thinking it can be a transmission issue.
Specs:
2000 grand am
3.4L V6 SE model
automatic
Camry :: 2.4 Engine - Misfire Codes And Rough Idle
The engine on my camry 2007 was overheated and I had the headgasket replaced but now it has misfire codes and rough idle this is a 2.4 engine I replaced 2 of the coils but still it has a rough idle... when the car is running it runs pretty good.
View 5 RepliesPassat (B5) :: Engine Rough Idle - MAF / O2 Codes P0103 And P0134
I bought a 1999(b5) passat, 1.8t(AEB) 5spd, came with a DIRTY K&N so i cleaned it with the cleaning kit....
Car drove fine, then: started it up after an hour or so.. it was idling rough, then would spike(17-1800), idle rough, idle fine, spike....etc. just random. it went away for a few minutes, so i tried to drive it home... got 1/8 mile into 3rd... and car just bogged down so i slowed to stop and turn, went to go, it was idling rough so i couldnt drive, just "hobble" into parking lot.... i let run, more random rough, spike, fine... so i let it sit, off. when i returned, it was the same, but now CEL light on...
Codes: P0103 - Mass or Volume air flow sensor circuit high input
P0134 - Heated Oxygen sensor - bank 1 sensor 1 (H02s11) sensor circuit no activity detected
Sonata NF (2006-10) :: 2007 V6 Misfire / Rough Idle But No Codes
I've got a troublesome misfire in a 2007 Sonata V6, 70k miles, which I have been trying and failing to track down for a long time.
More than a year ago, the owner of the car complained of rough idle. When this was first mentioned, I looked at the car, she and I talked, and I concluded that she hadn't changed the oil in some 20k miles. ...... Nothing else seemed wrong. I changed the oil, thinking that what she needed was an oil change.
Some time later, I was in the car myself and all of a sudden felt a strong bucking. Must've been a misfire. I recommended taking it to the Hyundai dealer, thinking the so-called 100k mile powertrain warranty would cover whatever it was (it didn't but whatever).
We drove it to the dealer. The dealer firstly informed us that the CEL had burned out, so we had missed some codes. The dealer further us the car needed new plugs and replacement of both upstream O2 sensors. Here was what the mechanic wrote:
"BETWEEN 35-40 PUT CRUISE ON AND WILL FEEL. CHECK AND ADVISE COMES AND GOES. MULTIPLE CODES STORED IN SYSTEM. ... P0300 RANDOM MISFIRE (ACTIVE), P0140 O2 SENSOR CIRCUIT NO ACTIVITY, P0154 O2 BS S1 NO ACTIVITY. WATCHED O2 VALUES AND FOUND ERRATIC READINGS. FOUND TSB 10-FL-012 SUGGESTING REPLACEMENT OF BOTH UPSTREAM O2 SENSORS. RECOMMEND COMPLETE SYSTEM TUNE UP FOR RANDOM MISFIRE. HOWEVER MISFIRE COULD BE RELATED TO O2 ACTIVITY.
So the owner went to a different mechanic and had the plugs, upstream O2 sensors, and one of the downstream sensors replaced. All OEM, I believe. ($$$!) (O2 sensor parts 39210-3C100, -3C200, and -3C400) Dunno why the downstream one was replaced, not my doing.
Following this, there was no real improvement. No codes either. The problem comes and goes, so maybe I thought it was fixed, but it has come back. Sometimes, it can be felt just slightly when the car starts cold. Other times, it can be felt just barely when driving at a consistent speed. Sometimes, the problem becomes really bad and jerks the car around. Other times, nothing.
What to check next? Coil packs? Intake manifold gasket? She never gets "top tier gasoline," but I would be skeptical that that's the problem. These are the top three suggestions I've heard.
Ford F-150 (2004-2008) :: 2006 - Rough Idle With Many Codes
I just received a 06 F150xl with a 5.4 triton and idles rough with the following codes! p0357 p0012 p0340 p0344 p0351 p0352 p0356 p0358 p0357 p0102 p0113 p0353 p0354 p0355 It's amazing the truck even runs and with no light on but it will accelerate. someone mentioned to clear the codes and drive it 50miles or so and read them again.
View 9 RepliesFord - Explorer :: 2004 V6 Rough Idle - Codes P2104 And P2112
I have a 2004 Explorer with the 4.0L SOHC V6.
I was having some rough idle and a P0401 code for Insufficient EGR Flow. In the process of investigating the EGR valve, I had to remove the throttle position sensor to remove the EGR. After re-installing everything, I had a worse rough idle and I again removed the EGR valve; however this time instead of removing the throttle position sensor, I removed the entire throttle body assembly.
After re-installing everything again, I now have very rough idle and no pedal response. I have the following two codes:
P2104- Throttle Actuator Control System Forced Closed
P2112- Throttle Actuator Control System Stuck Closed
I did not unplug any harness, and all connections are secure. I did not remove the battery cables while working on it, but I did remove the negative cable for about 45 minutes after getting the P2104/P2112 codes hoping a reset my fix things.
Sonata NF (2006-10) :: Rough Idle - Codes For Power Steering Pressure Sensor
My car has had a rough idle (no MIL). Scanned for codes and got the following:
P0552 - Power Steering Pressure Sensor - Low
P0553 - Power Steering Pressure Sensor - High
I'm picking up the part at the dealer this afternoon. I printed out a diagram of the component location, and it looks to be easily accessible.
Ford F-150 - 1997-2003 :: 2000 - Rough Idle / Codes PO304 And PO174
I have a 2000 F150 4.2L and I have 2 codes PO304 & PO174 so far I have changed my plugs & wires,fuel filter,mass air flow sensor, and coil pack...it is still running rough under a load and a little rough on idle..
View 9 RepliesFord Ranger / B-Series :: 2002 - Rough Idle Codes / Cylinder 2 And 3 Misfiring
I have an 02 ranger xlt 3.0, it started having a rough idle, codes say cylinder #2&3 misfiring, changed plugs, wires, coil pack, didn't work, still same code, checked injectors on right side, all 3 had ohm reading of 15.8-16.5, the injectors were clicking like they are supposed to, sprayed carb cleaner around the intake ports, didn't change the idle at all,what else can I check or do? with out tearing the engine apart, unless of course I have to, the truck has been very good to me, it's got 205,000 miles on it, I need it to last at least another year...
View 4 RepliesFord Ranger / B-Series :: 2004 - Rough Idle - CEL With P0303 And P0316 Codes?
I love my Ranger. I'm quite impressed with the power and durability. I'm ticked at Ford for stopping production.
I have searched my problem and could not quite narrow it down. I have also tried several remedies with no improvement. I need to narrow it down to a specific item.
2004 Ranger, 4.0 liter, 4x4, 131,000 miles, runs great above idle.
Problem: rough idle, idles at about 750 rpm's. If i raise the rpm's to 850 and up, smooth as silk.
The truck did this a few years back. Not quite as rough and it went away by itself.
Engine light came on this time with P0303 & P0316 codes. I have replaced: plugs, wires, coil pack. I know that the #3 plug is sparking quite well. the #3 injector is getting signal to spray not sure if it is. I have 4 O2 sensors and I believe I tested them correctly (passed). The passenger side upstream or pre cat sensor has not been tested yet. Had to rent a tool and will do that in morning. I slid a piece of aluminum roof flashing between the crank position sensor and the crank pulley. Not a noticeable difference. While at idle (750 rpm's) I pulled each (#3,2,1,) (one at a time) injector wire plugs off the injectors. No noticeable difference. I pulled the vacuum line off the egg and operated it with a vacuum tool. Seems to be working fine. Sprayed carb cleaner around on vac lines. No engine surge
Ford F-150 - 1997-2003 :: V6 Rough Idle / Black Smoke / Throwing 6 Codes
so i bought this truck about 3 months ago and it was running real bad when i got it, I went ahead and changed the lower and upper intake gaskets, cleaned throttle body, egr ports on lower and upper intake, did timing chain cover gaskets and 3 bad injectors i found while doing gaskets, truck ran better but still black smoking(running rich) and getting 8 mpg. So I changed fan clutch,fuel pump fuel filter,airfilter,MAF sensor(old one was pulling 14.4 volt), DPFE sensor and all 4 oxygen sensors(old ones carboned up and real sooty).
I've checked my egr valve while idling and when it opens the engine just about stalls, truck seems to be running better but CEL light came on again and is throwing these CODES:
P0453 (evap emission ctrl sys pressure sensor high input),
P0141,
P0153,
P0135(oxy sensors),
P0401exhaust gas recirculation flow insuff detected,
P0460fuel tank level indicator circuit error.
And I believe I've told everything i know ...
Sebring - Chrysler :: Rough Idle And Engine Light Comes On / Codes Read Misfires On 1, 3 And 5 Cylinders
I have a 2006 Chrysler Sebring Convertible 2.7L engine. Replaced water pump and spark plugs. We triple checked the alignment on the chain and are sure the timing is fine. Car started right up. Now running rough idle and engine light comes on. Codes read misfires on 1, 3, and 5 cylinders.
View 8 RepliesFord F-150 (2004-2008) :: Rough Idle / P0012 - Misfire Codes Associated With Bank 1 And Cylinder 3
5.4 3v. my last few weeks have not made me a fan. Here are the details:
I bought a 2008 F150 XL 5.4 3v with a cam phaser knock. Have done other timing jobs in past with no trouble so I was not too afraid to tackle this one. famous last words...opened the motor (shout out to the passenger side valve cover and its designer here) and found semi damaged roller follower on driver side. Worn cam lobe on the corresponding lobe and a loose chain on passenger side. proceeded to :
Change all timing components: phasers, chains, tensioners crank sprocket, all applicable bolts and BOTH cams as well as all lash adjusters and roller followers. most looked fine in fact all really did with a bit of wear on a few roller followers but only one bad one. engine didn't look to bad pretty clean.
Double and triple checked my timing chains and it was spot on. dark link on spot on crank, two dark links on the L and R dead on. put it back together. oh yes, changed all plugs with motorcraft ones, didn't even break one. did not change vct solenoids because I falsely assumed I could change the later easily if needed. they looked ok. screens intact etc... silly me for not realizing how kind Ford was in 2007 and later to necessitate removal of valve cover. I was reading a previous one on the how tos and assumed later models would be the same since it was the same sensor...
Cranked truck ran great. I mean perfect. sounded perfect. ran like a scalded cat. till it got to hot idle then it started doing its thing. rattle shake till you revved it. ran fine just wouldn't hot idle fine especially in reverse or under slight load. replaced driver side vct since ford only had one and I started on the easy side ordered the other one waiting for it. seemed to improve dramatically meanwhile I am driving this truck to test it. I drove it to work 50 miles each way and it ran great.
After a few trips it popped the P0420 light, seemed to run ok, cleared it watched it wouldn't come back. O2 sensor did seem to imply a bad cat on bank 1 since it seemed sensor two was mimicking sensor one and not staying stead like the other bank. still ran fine,
So I decided to check back pressure on the cat. I pulled sensor one out of bank one (really a joyously tight squeeze in there) hooked up my gauge and got 0 back pressure. revved it and all nothing. hooked sensor back up pulled truck out of shop and it commenced to running like crap. I mean bad. running worse than before I got it. Popping P0012 code continuously, and tons of misfire codes associated with bank 1 ..cyl 3 etc.. I tried swapping coils, pulled coils and checked spark with a tester and firing away looks like tons of good spark.
Now the weird part is : looks like bank one is dead. I can unhook any coil pack and/or injector and it runs the same and sounds like it is missing. if I unhook one off of bank 2 it almost dies or does. so bank 2 seems to be running fine. it will start and run but sounds like it missing sets flashing check engine light and backfires and stalls like crazy. I even second guessed my pressure gauge and unhooked exhaust manifold from pipe and it sounds even prettier when it backfires out of there but no change. I pulled cam sensors and cleaned it again and even tried swapping them since they looked identical but no change so I put them back.
Now I can only surmise that I am out of time somehow? or I have a gremlin perhaps? I like working on cars (usually) but this one is getting old. how do I verify what is wrong. if it is timing related how do I verify that now definitively once my marks moved I really cant figure out how to tell if it is in time? Since it has all new parts and they all ran beautifully till now. could it possibly be the vct solenoid doing all this? I plan on changing it when it comes in but surely it cant cause this many problems.. I unhooked it no change, and it does it at a cold idle and any rpm. really runs worse at idle but bad at any rpm.
Ford Ranger / B-Series :: Steam Out Tail Pipe / Misfire Codes And Rough Idle
Steam out the tail pipe, misfire codes, rough idle. No water in oil, no over heating. Head gasket ??
View 3 RepliesLexus SC430 :: Convertible Top Will Not Close / No Codes Show Up
Top won't close,the button seems to be dead, my question is can you replace the button that opens and closes or do you need to replace the whole climate control panel. There are no codes that show up. When I press the button down the windows go down but no top working, package tray in the trunk is closed and luggage button is off.
View 14 RepliesFord F-150 (2004-2008) :: Misfiring - Rough Idle - Got Codes P0340 / P0344 / P0345 And P0349?
I recently purchased a Ford pickup. I bought a 2004 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 200,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run good when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come to on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
Ford 6.0L Power Stroke Diesel :: 2005 - Rough Idle - Codes P0672 / P0674 / P0678
I have a 2005 f350 6.0 power stroke. I had a crank no start when hot issue. I bought an obd scanner with the torque app. IPR was at 85%. ICP pressure was low. I got the IPR out and bought a new screen because it was clogged. Upon putting in I broke the injector female side plastic connection.I bought the injector connector piece and installed it. After putting everything back together it starts but runs very rough,low power. The IPR was fixed. ICP,ipr and ficm are at good levels now.
IPR=14.7%-30%
Fcim sync=1.0
Fcim voltage=48.5
ICP pressure (idle)650-850psi
My fault codes are:
P0672 (glowplug)
P0674 (glowplug)
P0678 (glowplug).
Why it would be running/idle rough?