Golf/GTI VII :: Spring Binding Popping Noise After Neuspeed Race Spring Install

This noise I have is driving me crazy, installed neuspeed race springs and now I have this weird spring noise, sounds like the springs are binding and then releasing when you turn the wheel, like a clicking dinging noise, it's on both sides and happens when moving slow and turning the wheel and when stationary and turning wheel, it sounds like tug and release not really spring bind I checked install and everything is correct even disassembled bearing assembly and everything is fine, lubed spring seats with silicone paste nothing is working.

When looking at the spring and turning wheel it's almost like the spring is getting stuck on the middle part of the seat then releasing, I know this was a common problem on the mk6 but I haven't heard anything about the mk7 the spring is seated in the lower perch perfectly the upper is were the noise is coming from you can see as you turn the upper bearing by hand it actually somewhat twists the spring and then releases and that's what makes the noise, and it dose not move in a nice circular motion kind of like an egg shaped rotation and it makes the spring flex and pop I think there's a problem with the springs,

View 5 Replies

Golf V R32 :: Rusty Hatch And Front Fender?

Having rust issues? I just bought the car and noticed some was touched up with the rear hatch - under the window, right by the seal. Also, right by where the bottom of the door and front fender meet. Looks like it's inside, on the body/frame, not the fender.

I'll probably take it to dealer and hope to have it taken care of. Carfax came back clear so I'm pretty sure no work has been done on it before that would cause this.

View 3 Replies

Golf IV / Jetta IV :: Rusty Passenger Side Rocker Panel

Recently I made a corrosion claim about some rust forming on my jetta. Long story short VWOA accepted to replace my passenger side fender and trunk, but refused to replace my passenger side rocker panel. Once all the warranty work is taken care of I would like to treat the rocker panel rust the best way possible. I'm not looking to spend hundreds of dollars on this procedure, but I don't want there to be a hole in my car by next winter.

Personally I'm thinking of sanding it all down, treating the rust, applying some paint to it, and then trying to protect the area a little more by investing in OEM side skirts.

View 23 Replies

Ford Super Duty (1999-2016) :: 2003 - Clock Spring Has 8 Spring Wire?

Adding cruise control to F350 XL I just bought. I got a steering wheel with the buttons. But I am having problems with the clock spring. Mine has an 8 wire plug with only 6 pins on the big plug and all of the clock springs I have found have only a 6 wire plug for the big one. Without changing my clock spring I have no where to plug in the cruise wiring. All have been for right year model with cruise and even tried different years but none will plug in under the dash.

View 3 Replies

Ford Super Duty (1999-2016) :: Conversion Of Leaf Spring To Coil Spring?

Conversion from the dana 50 to the newer dana 60 with coil spring? My Dana 50 has called it quits so while my front end is already off the vehicle already why not make improvements. Ford used the 50 for 1999 to 2002 then upgraded to the 60, I'm guessing it was for a reason!

I've read this article on a similar project but the dana 60 had leaf springs as well: Dana 60 Conversion for F250 years 1986-1996 .: Articles I'd prefer coil spring, nothing more then personal preference with a bit of better ride quality. The donor vehicle is a 06 SRW F250 This is not what I'll be getting but just as an example of the parts I would get.

View 10 Replies

Ford Fuel System :: Gas Line Spring Lock Coupling - How To Release Garter Spring

I hope i don't give the impression on my very first post that I'm a total retard......but ...I can't figure out for the life of me how to get those spring line coupling apart! I've removed the clips...but it just won't pull apart. Is there a tool to release the garter spring?

View 4 Replies

Golf/GTI VII :: How To Install VER Spring

I'm having trouble getting the strut back through the steering knuckle. I used the 1/4 ratchet to spread it and get the strut out but I can't get the strut to go back after installing the VWR spring. I've tried speaking with many tools now and it's just so damn stuck. I hope I haven't damaged anything by hammering a wedge into the point where the ratchet is supposed to spread it. After a couple of tries the ratchet doesn't seem to spread it at all.

View 2 Replies

Golf V R32 :: Alignment After Spring Install Necessary?

Is an alignment after a spring install necessary?

Getting my H&R springs installed tomorrow and was curious

[URL]

View 4 Replies

Golf V R32 :: Clunk Noise In The Front Spring

I just installed Neuspeed Springs and my car is taking a "clunk" in the front spring, I went back and I replaced the strut bearing mount and the noise still continues.

View 8 Replies

Golf V R32 :: Paint On The Spring Is Starting To Flake Off

I have a set of V Maxx's on my car for a couple of months...and i noticed that the red paint on the spring is starting to flake off...is there anything i could do to re-coat them or something? this happened on my patec coilovers on my MK IV.

View 8 Replies

Golf/GTI VI :: Suspension Clunk After VWR Spring Install

I just had a set of VWR springs installed on my 2011 GTI (35,xxx).

I've noticed a very discernible clunk coming from the driver's side front wheel particularly when traveling over a dip in the road (when the spring and suspension is extending). The sound only comes from the one wheel well - the other three sound fine.

I'm bringing it in for an alignment tomorrow (recommend after the spring install). Sounds almost like a bad bushing?

View 11 Replies

Golf IV R32 :: Front End Noise Like A Broken Spring

I have a noise like a broken spring, changed strut insert, top mount, checked for loose brake shield and pads. Removed both sway bar links. [URL] .....

View 3 Replies

Golf IV / Jetta IV :: 2004 GLS 1.8t - Lowering Spring

My wife has a 2004 jetta gls 1.8t we just got some stock 18" bbs gli wheels . she wants to lower it some. Not really wanting to spend the money for coil overs... she will never adjust them and shes not racing it... just want it to look better. How much to lower it...

View 9 Replies

Golf IV R32 :: Loosen Sound - Rear Spring Collapsing?

I got bilstein PSS9's at waterfest this year and it has been on my car for approx. 7k miles and I think I am experience the problems that people say about the rear spring collapsing. Whenever i drive on a bumpy road, it sounds like something is loose in the rear specifically the drivers rear. I thought it was the heat shield but i had that tightened and the sound is still there. My rear end is not even lowered alot. I turned the coil about 1-2 times. the front is even lower than the rear. I don't know whats up but its frustrating me. I also have 20mm spacers in the rear, would that have to do anything that is causing this sound.

View 16 Replies

Golf VI R :: Steering Wheel Squeak After Clock Spring Recall

I had the clock spring recall done last week and now when I turn my wheel almost to full lock for a tight turn, it has a little "chirp" when going past a certain point. I'll definitely bring it back to them to correct it, but I'm guessing no quick fix but I can easily remove my airbag and check from there.

View 4 Replies

Golf/GTI VII :: Squeaking Noise From Driver Side When Go Over Bumps After VWR Spring Install

Instead a set of VWR springs yesterday on my GTI. Initially driving it, everything seemed fine. After about 20 miles and taking an off ramp aggressively, I noticed a squeaking noise from my drivers side when I go over bumps. I cannot pin point what may be causing it.

View 11 Replies

Golf IV / Jetta IV :: Noise Coming From Rear Struts As If Spring Is Wobbling Around

So I finally installed my brand new coils in yesterday. I took it for a test drive and noticed a noise coming from the rear struts. It sounds as if the spring is wobbling around, almost like a clicking sound. When I first installed them I installed them without the rear perch, then when I heard the noise I thought it was because I didn't install the perch so I ended up taking my wheels off and installing the perch back in. No luck. It's still making a clicking sound when I'm driving, constantly. I had my friend push down on the rear of the car several times while I look under it, I don't know what it could be.... I also cut my rear bump stop in half. Could that be the issue? I have about 10 threads left on the rear perch before I max out.. The spring is compressed half way. Once again, These coils are brand new.

View 5 Replies

Golf/GTI VII :: Intermittent Clunking Sound From Rear Suspension After VWR Spring Install

I recently got an MK7, coming from a MK5, and I installed the VWR springs 8 days ago. Since then I've noticed an intermittent clunking sound coming from the rear suspension. I installed springs on my MKV without any issues and again on several other cars, soIi'm familiar with the process. Everything was torqued to spec after the install.

My best description of the sound would be a clunk, not any rattling, clicking, or squealing. The sound is greater in the passenger side rear than the drivers side rear. No issues with anything up front. Sometimes it occurs when I'm turning the steering wheel while backing out of parking spots and driving slowly, other times when I hit bumps in the road, but it is not constant nor does it seem dependent on the size of the bump/pot holes in the road.

What may be causing this? My plan was to give it a week for everything to settle before I tore everything apart to look for any culprit.

View 1 Replies

Golf V R32 :: Anti-Rattle Spring Damage After Replacement Of Brake Pads?

I took my R to a local mechanic to have my rotors turned and my brake pads replaced (RedStuff). A couple of days later, I noticed a loud noise coming from my front passenger wheel well when I was driving, and the pitch changed when I hit my brakes. It appears that the anti-rattle spring was not reinstalled properly because it has fallen in between my caliper and rotor, causing damage to the rotor and my aftermarket wheels. Since I'm not much of a DIYer, I wanted to get your opinion on the situation and how I should approach things with my mechanic. How hard is it to properly install the anti-rattle spring?

View 7 Replies