Passat (B5) :: 2001 - Misfiring - Got Codes P0300 / P0301 / P0302 / P0303?
i have a 01 passat with a v6 in it on 4 motion and im having an issue with soem mis-firing
i pulled the codes. P0300 P0301 P0302 and P0303 which are all saying that there are missfires in cylander 1,2 and 3 and random miss fires.
im also getting a P0340 which is cam sensor A or the right hand bank. problem is i just replaced the cam sensor and when the motor got warm, the code came back. I was told by the previous owner that the car needed a Coolant Temp Sensor....can this be the cause of my mis-fire issue? hear me out.... it only happens when the car is warm so im thinking that the car is warm but the ecu thinks its cold cause its not getting a good signal from the CTS. thus its either advancing the timing as if the motor is cold and cuasing a miss fire or something along those lines. any thoughts?
Golf/GTI VI :: Misfiring - Code P0300 And P0302
I have a 2011 GTI (purchased new in 2010) with a stage 1 APR tune and a carbonio stage 1 intake. 71K miles on the car, tune has been on it from nearly the beginning, no issues. I have religiously filled with 93 octane gas -- like, always. The other day I was filling up an empty tank in NJ -- land of mandatory attendants -- and I accidentally said "premium" instead of "super." (I normally self-serve in PA). Before I realized what had happened, I had a full tank of 91 in the car.
I run the 93 octane program on my APR, and I couldn't remember how to switch, so I've been running around the last few days that way, seemingly with no issues. I'm not even sure what's supposed to happen if you burn 91 while in the 93 program.
Anyway, yesterday I happened to go full-throttle in 1st or 2nd gear, and I ran into a little stumble. Strange, but I figured maybe this was the result of my refueling mistake. So, I got out my APR manual and figured out how to switch programs down to the 91 program, which I then did. Took the car out again, and was still able to get it to stumble, eventually with a blinking, then solid CEL. A quick VCDS check showed a "Random/Multiple Cylinder Misfire Detected" -- P0300 and "Cylinder 2 Misfire Detected - MIL" -- P0302.
Now at 71K miles, I've never replaced the coils or the plugs, although I have had 2 intake manifolds replaced under warranty. I'm kind of figuring the octane and tune are not really causing this and it's probably just in need of some coils/plugs. what is "supposed" to happen if you run 91 octane on the 93 program? I haven't tired backing down to stock yet, but I could certainly do that and see what happens.
Golf IV / Jetta IV :: Throwing P0300 / P0302 And P0303 Codes
The car doesn't seem to run that rough.
Replaced coil pack and spark plug wires with parts from O'reilly auto
16684 - Random/multiple cylinder misfire detected
P0300 - 35 -10 - Intermittent
16686 - Cylinder 2
P0302 - 35 - 10 - misfire detected - intermittent
16687 - Cylinder 3
P0303 - 35 - 10 - misfire detected - intermittent
I have searched and browsed multiple websites and threads to no avail. They all seem to be dead ends.
Corolla :: 1999 - Fixing Misfiring Code P0303 On Cylinder 3?
The issue with 99 Corolla CE with 147,000 miles....
I have a misfiring P0303 Code - Cylinder #3 Misfire. Here is what has been done in an effort to remedy the misfire. A major tune up, new spark plugs, new fuel injectors, new spark plug wiring, new coil packs, The car runs ok once warmed up but in the morning the engine vibrates until warm and also shivers a little while the car is stopped at a stop light. I have dropped it off at the mechanics a couple of times now to no avail. Once the code is reset it will not display the CEL for a couple of days but the symptoms still remains. The CEL comes back on within 2-3 days with the same code. Really frustrating! Well, at least this time CEL in not flashing like before it comes on and stays on.
Gmc - Sonoma :: 1997 - Code P0300 / Misfiring
I got a 1997 sonoma which has a p0300 code. I changed the plugs and wires, cap and rotor and the pcv value, and it still misses. what could this be?
View 18 RepliesFord F-150 (2004-2008) :: 2005 - Smoking White - Got Codes P0174 / P0300 / P0305 / P0306 / P0316?
05 2 wheel drive f150xl 4.2 l 135,000 miles. Smoking white out of exhaust. More at start up but doesn't go away. Turns a little blue. When parked at idle if I bring up the RPM's quick I will get a little puff of black in the white smoke. I can't smell or taste(when I touch my fingers to mouth) any anti freeze in the exhaust smoke but I live in Myrtle Beach and I have little if any anti freeze in the coolant. I flushed the motor, changed oil and filter and added a can of seafoam. I took the throttle body off and cleaned it. I also replaced the air filter because I went down a dirt road and hit a deep water hole. Dirt and mud got into the air filter and by passed it also. This was the reason for the engine flush also. I can't recall any smoke before this. Maybe a puff on start up from moisture not sure. Im going to buy a coil pack and plugs and start from there. I have never had this many codes.
P0174 Bank system 2 to lean P0300 random multipl Lean mil. Missfire detected P0305 random multiple Missfire detected cylinder 5 misfire P0306 cylinder 6 Missfire P0316 Missfire detected on start up first 1000 revolution
Toyota - Avalon :: 2000 - Rough Idle - Steady Misfire - Getting Codes P1150 / P0300 / P0302 / P0304 / P0306?
I have a 2000 Toyota Avalon XLS with 134k miles, engine is a v6 (3.0). It has a rough idle and a steady misfire. You can drive it sometimes and it will run perfect and you can drive it sometimes and it will misfire. I am getting codes P1150, P0300,P0302, P0304,P0306. Driving me nuts.
View 1 RepliesFord F-150 (2004-2008) :: Gode Codes P0172 / P0300 And P0303?
My son just left. We scanned his truck and got these codes.
P0172 Bank 1 rich P0300 random misfires P0303 cylinder 3 misfires.
I used the Torque APP Pro to check these codes. I went to live readings in the Torque APP and saw some readings for Long term and Short term bank 1 Readings.
They are all "greek" to me, and I don't recall what they were, but could get those readings tomorrow.
When I have done searches combining these codes together, I see changing spark plugs. P0172 alone gets me a different train of thought. Mainly CAT issues.
Also, his cranking to start is quite long. (A lot longer than my 6.0L would ever think of cranking) At least nearly 30 seconds of cranking. We are leaning toward first just changing #3 plug.
Cadillac - Cts :: 2004 - Check Engine Light Flashes / Codes P0300 And P0303
My 2004 Cadillac CTS 3.6L started running rough, check engine light flashed on and off. Codes P0300 and P0303. The car has about 119000 miles. Could this just be the plugs? The car has been running fine up to today.
View 2 RepliesPassat (B5) :: P0411, P0011, P0300, P0301, P0303 - Misfire / Sputters And Hard To Drive
2002 Passat 1.8T
Backstory. The P0411 code shes had for quite some time. I think probably 4 years maybe. Just never did anything about it because I guess they are expensive to fix. Thats the SAIP and combi valve correct? Anyway to remove all the emissions stuff and get the codes deleted?
So, about 3 weeks ago, maybe a little longer i cleaned her engine bay, replaced a few vacuum lines because the shop she took it to last year did a terrible job. Mind you, they did a head gasket, timing belt and some other minor things while they were in there. And they couldn't take the time you run new vacuum lines, since they just cut the originals and used a bunch of t fittings to "solve" the problem.
Anyway, i replaced the lines and it seemed to run better at idle, still had a little mis at idle but ran smooth at speed. I also did an oil change, put some fuel injector cleaner in it, put some seafoam in the oil, and cleaned the engine bay thoroughly. I did it properly and took all the plastics off, cleaned them, scrubbed the bay and used an air hose to get rid of the excess water. Left in a nice state. Ran smoother, looked better, so on and so forth.
Fast forward to last week, and she mentions to me her car isnt running right. Its sputtering, hesitates, running rough, exhaust is puttering, and it used up a lot of gas. She parked it for a few days, and i came down to look at it. Mind you, i don't have a code reader. So I looked at it blindly thinking it had an ignition issue. Nothing could have changed that quick since i looked at it.
So, today we got one coil(just in case ones bad), and 4 new plugs (Autolite Iridiums). Replaced and gaped the plugs to .030, torqued to 23 ft/lbs and started the car. Seemed to run a bit better, but subsided quickly. I then pulled each coil harness plug to make sure it would misfire on each cylinder and it did. So, new plugs and the coils checked out. Time to get its codes read.
Took it to the Pepboys and the codes it came back with were the P0011, P300, P0301-3. Cleared the codes and they came back nearly immediately. I had the dreaded P0011 code. The misfire codes im guessing were from the coils being pulled on each one, and also due to the P0011. Now i read a lot of threads about the P0011 and how its usually not the camshaft position sensor. However, i pulled the plug on that while the car was running and nothing changed. So i thought it could be the CPS. Changed that out and still nothing.....
Golf IV / Jetta IV :: Check Engine Code P0303 - Misfire
I have a 2000 VW Jetta 2.0l AEG engine with 190,000 miles and check engine code P0303 for the 2nd time in 3 months. I had this same code 3 months and 3000 miles ago and found the spark plug #3 to be fouled up. All other plugs and wires seemed to be okay so I replaced plug #3 and the problem went away. I suppose after I take off the upper intake manifold I am going to find the same plug #3 to be fouled up again. The engine is a typical AEG that I have to add 1 quart of oil every 1000 miles as it has been burning the same amount of oil since I acquired the car at 135,000 miles. I have read that the wrong piston rings were installed from the factory on a large number of these engines and VW says that if less than 1 quart of oil is burned after 7500 miles it is normal. I really don't feel like spending 2 hours every 3000 miles to replace plug #3 ? It might be time to part ways with my 2nd VW. As a side note, this car has been averaging 35.5 mpg over the last 55,000 miles that includes 50% city/ 50% highway driving. I coast to red lights and don't accelerate quickly with the 5 speed manual transmission to achieve hybrid like fuel efficiency.
View 1 RepliesGolf IV / Jetta IV :: Catalytic Code / Cylinder 3 Misfire P0303
I own a BMW not a VW! My 19yr old daughter purchased her first car a few months ago, an '03 Jetta 2.0L with approx. 170,xxx miles. Just after she got it we pulled a P0420 code, but it ran fine so we haven't worried too much about it. I've cleared that code and after about 2 weeks it will come back. Last week it started to have some issues with rough idle, stumbling/hesitation. I pulled the codes yesterday an in addition to the catalytic code is a cylinder #3 misfire P0303. I thinking the 2 codes are not related. I'm assuming the typical things to look for on the misfire are coil, wire, plug? Looks like the coil on this engine is a combined unit so no switching coil packs to see if the miss follows a bad coil pack.
View 4 RepliesGolf IV / Jetta IV :: Getting P0300 Code?
Yesterday I went to star my 2.0 Jetta and it instantly starting sputtering at idle. After maybe a minute of sputtering the car died. Tried restarting it and it would instantly die after starting. Car threw code P0300: Random Misfire.
As of today the car now runs again with no problems. No codes. I didn't touch a thing and it seems to have resolved itself.
The entire engine bay was wet from condensation due to temperature change. Is there any way this could've contributed to the misfiring? I'm thinking the spark plug wires might have gotten wet and that was causing the misfire.
Golf/GTI VI :: 2010 - Code Read P0303 Misfires Cylinder 3 Detected
I recently bought my 2010 gti used with 62k miles on it about 3weeks ago. The car had an carbonio intake stage 1 and a stage 1 tune from Apr when I had bought it. On the test drive and for the first two weeks I had it I did not have any problems. A few days ago on a cold start my car threw an MIL and it was flashing. When I got to school I plugged it into the obd2 scanner. Code read P0303: misfire cylinder 3 detected.
My teacher and I went over possibilities of the misfire. Coil pack, plugs , injector, valve float( even tho this should not occur at 1300rpm cold start) we also thought that maybe because the car is direct injection the valve was not closing all the way due to carbon build up on the top of my valves which in this case I'm glad I don't have an interference head. I moved around the coil packs. What is the cause of this? I'm only misfiring at start and when the engine isn't warms up to operating temp.
Accent MC (2006-11) :: 2007 - Misfiring Codes P0300 And P0302
My girlfriends 2007 accent as thrown codes p0300 and p0302.
After reading everything I could find, I had coil pack on my list of possible problem items.
The car sat in the driveway yesterday and when she went to start it today, she couldn't get it to.
I got it to start when I got home by giving it some gas while turning the key, but I don't want to drive it anywhere.
The hard start is leading me to believe it's the coil pack.
I was going to start with changing the pcv, spark plugs, and run fuel injector cleaner through it because those are the cheap possibilities...but now may add in a new coil pack.
Santa FE SM (2001-06) :: 2002 - Misfiring / Codes P0171 And P0300 Came Up
My car is misfiring, codes p0171 and p0300 come up on the code reader. It idles rough and has very little power. I have checked my exhaust , it is not plugged. When I unplug coil #2 while idling there is no change as to the engine performance so I switched the coils around with no difference when coil is unplugged on cylinder #2. I have changed the plugs, there is power to the coil, all plugs are firing and when removed plugs 2 and 3 are wet with fuel indicating I am getting fuel and fire. I have replaced the cam sensor with no change.
View 3 RepliesSanta FE SM (2001-06) :: Code P0306 Came Up - Cylinder 6 Misfire
I have a 2004 Santa Fe with the 3.5. Today I started it and the check engine light came on. It was not on before this. (We had a lot of wind and rain from the storm but nothing major.) And seems to be running fine. I went to the auto parts store and they ran a diagnostic and the Code P0306 came up #6 cylinder misfire. They said probably Spark plug, wire or coil for #6, then went to look up code in computer and did not have my truck so they went with Kia or Domestic, which gave different possibilities for a code P0306.
They had me buy some fuel injector cleaner as injector was on the list. The light is still on so I guess the cleaner was not the magic bullet. I spoke to a lady at another auto parts store who is a wiz when it comes to cars and has been around them and fixing them a really long time. She says the Code P0306 is Spark Plug, wire, coil #6. She has a 4cyl Hyundai car not truck and she had the code for her #4 misfire in the past and she started her repair cheapest first, Plugs, wires her code was still there she then changed the coil and that did the trick for her.
I on the other hand can't do this stuff myself. Can't afford the dealer anymore or to have a shop do a tune up AND coil if I don't need all new plugs and wires just a coil as they will charge a lot to do a lot all. And it may not need it or even be any of those things. I also suspect the dealer and shops will want to still hook up their computers to do an costly diagnostic because the light is on, even though I know the parts store already came up with a code P0306 twice. Spoke to the dealer on the phone and he already basically said they would want to do that first for $100 plus the cost of repair.
I brought the truck new. It now has 91,500 miles on it and the dealer has already done two tuneups on it in that time, Plugs and wires. I hear it probably shouldn't have even needed these tuneups in this amount of millage? So the last one was probably about 2 years ago and a few thousand miles maybe a guess 10,000-20,000 miles ago. Do you think a plug and wire would be bad already in that few miles?
Town Car :: 1999 - OBDII Code Is P0306 Cylinder 6 Misfire
I have a 99 town car with 78,000 miles. I filled the tank and have run about 1/4 tank when the engine started to misfire. Got the Service Engine Soon light so went to O'reily. The OBDII code is p0306 cyl 6 misfire. What would you check first?
View 3 RepliesFord F-150 - 1997-2003 :: Code P0306 - Cylinder 6 Misfire
So my 99 F-150, 4.2L started throwing a code a few weeks ago, P0306 #6 Cyl Misfire. This thing has got 238,000 and has been the most reliable commute vehicle I've owned.
Today I changed all the plugs and wires (they were due anyways) which didn't resolve the issue. After clearing the code, got about 3 miles out and it came back. Running SeaFoam through the system on this tank as well, but I'm leaning towards an EGR blockage like what is described here:
Sparky's Answers: 1999 Ford F150, P0306 Misfire Cylinder #6
I was about to buy a new coil pack but I'd rather not continue to throw parts at this, as I've read many others do with this same exact situation, only to end up with the same code. I've replaced the coil pack once already a few years ago when I lost a cylinder on the way to work.