Ford Ranger / B-Series :: 1995 Not Getting Gas When Floored To Pass

1995 Ford 4.0 ... All the following have been replaced on the truck.

High Pressure Fuel Pump and assembly
Idle Air Control Valve
Spark Plugs
Oxygen sensor (Bank 1 sensor 1 Oxygen)
Fuel Filter

The most recent item that I replaced is:

Coil Pack
Spark Plug Wires

Now, with the Coil Pack replacement, the truck drives good, as long as I do not floor it (After it heats up, about 15 minutes). Basically, if I try to pass someone, the truck acts as if it is chocking out, like it is not getting any fuel.

Before replacing the Coil Pack. It would chock out at any given time, rather just barely pressing the gas peddle, or just sitting idle.

I took it to a friends muffler shop, and he stated that it is not the exhaust that is causing the issue. I am at a loss. Is there anything else that I can check?

The truck seems to drive fine, as long as I do not get down on it, and try to take off fast after it heats up. When it is cold, I can take off like a bat out of hell, and it runs like no-ones business.

View 14 Replies

Lexus IS 2014+ :: Floored The Car For About 2 To 3 Seconds On Cold Engine

Paranoid about my car. Basically what happened was after work I walked to my car and there were a bunch of guys who were meeting up in the parking lot and were complementing me on the car . I always let the car idle until RPM reaches 1,000 and I did that today and as I was driving off I decided to show off a little and I floored it . just for about 2-3 seconds. it was about 70 degrees out and the car was sitting in the sun so the engine shouldn't have been to cold

I know it is bad to floor a car on a cold engine, so my question is how bad could I have potentially damaged my engine? it was sitting for about 3 minutes and RPM idled out to 1 but the hot/cold bar hadn't risen yet. it was the first time I did it on a cold engine and I bought the car so I want to do whats right to keep it running smoothly.

View 14 Replies

Touareg :: When Floored The Engine Is Ticking At Higher Rpms

Experienced a ticking noise when at WOT with the 4.2 V8 engine? When cruising around the engine sounds fine, but when floored the engine (i believe) is ticking at higher rpms. Hard to believe its the engine, only 24k miles on it, with regularly changed oil. Sounds like either detonation or valve interference.

View 10 Replies

Venture :: 1999 Engine Low Idle And Stalls When Stopped / Parked After Driving On Highway

I have a 1999 Venture Van. The engine has a low idle and stalls when stopped/parked after driving on the highway for 10 minutes or longer. Whenever I drive it to the train station in the morning to go to work, it dies as soon as I park it. It will start up again fine right away tho. I drive 10 minutes on the highway.

The engine light is on, but goes off sometimes for months before coming on again. I've brought it to at least 3 mechanics and they can't get the light to stay permanently off, and say to just drive as-is. But that still leaves me with the low idling problem. It doesn't always stall, but the potential is always there, as you can hear the low rpms threatening, and dread stopping at a light.

I had the engine light interpreted as P0122 TP SENSOR CIRCUIT LOW. The mechanic replaced the Throttle Positioning Sensor. Engine light came on again 2010. Mechanic did a Computer system check/smoke test. Diagnosed a Leak in evap system so they installed a new gas cap and vent valve. 2 months later, engine light went on again.

New plugs, spark wires, fuel filter, fuel treatment, fuel line, gas cap, vent valve.

1 month later light is on again, and low idling persists. I put alot of $ into the problem with no solution. Some mechanics say the engine light has no relation to the low idling.

Wife wants me to get rid of it, but the Van is in great condition except the low idling/stalling problem. I don't care if the light stays on, as long as the low idling/stalling stops. Can't I just ask a mechanic to increase the idling rpm?

View 6 Replies

Jeep - Grandcherokee :: 1999 - Engine Stalls For 5 - 10 Seconds And Fires Back Up When Driving On Highway

My 99 jeep grand Cherokee 4.7 v8 4x4 will not start after 2 to 3 short trips. it starts up fine in the morning when the engine is cold but driving for a while while and I stop somewhere and shut the engine down for a few minutes it will not restart.. after I wait 10 to 15 min it start up ok.. Next when I'm driving on the highway, after 10-20 mins of driving, the engine stalls for 5-10 secs. and fires back up..I inspected all connections and the starter which were ok but I did find that the starter is soaked with oil dripping from the valve covers.. Could the oil be the problem..? Even causing the stalling out on the highway..?

View 2 Replies

Ford Super Duty (1999-2016) :: 2014 F250 6.2L Gas Engine Stalls At Highway Speeds

2014 F250 SuperDuty 6.2L gasser, x-cab long bed work truck. 105k miles, original owner, 1 driver, mostly highway miles, well maintained and super clean truck.

First issue occurred at 83k miles, Aug 2016. Warm summer day climbing I-70 in CO, slightly loaded, and just entered the Eisenhower tunnel (11,150' altitude). Lost power, no RPMs - not running, I put it in N and rolled as far as I could. Hazards on and no-where to pull over, hugging the wall and blocking one lane. Power OK - will crank, no fire. 1/3 tank on the fuel gauge and >100 miles distance to empty on the trip computer. Tunnel rescue shut down traffic and pushed me out into the daylight.

After waiting an hour to fill our paper work for disabling the interstate tunnel I returned to the truck which quickly started. No symptoms, no lights, no codes. Topped off the fuel tank after a easy 15 mile drive downhill. Drove another 800 miles symptom free to my destination and checked it in at the dealer. At this time a check engine light had finally illuminated - PO420. I shared the story of stalling out at highway speeds with the Service Writer. Dealer replaced the cats, confirmed fuel pressure OK, computer condition OK, serviced the trans (at my request).

No symptoms reoccurred during the next 20k miles until last weekend. 105k on the OD now. Heading to Flagstaff, AZ on I-40 in similar conditions. Hot, AC running, climbing in elevation, slightly loaded, running on the bottom 1/3 of the fuel tank... Died while cruising at 79 mph. Well, at least this time I wasn't in a tunnel and had a shoulder to pull off on. Deja-Vu - full power, radio on, no engine lights, gauges normal, fuel reads over 1/4 tank, >100 miles till empty on the trip computer - won't start. Cranks, but no fire. Some sputtering during start attempts must have triggered the next trouble code.

Opened the hood, removed the gas cap, let it vent and cool for about 30-40 mins while I took a walk. Returned to the truck which easily started and let me drive to the next fuel station, 30 miles away. This time the check engine light stayed illuminated. It took 24 gals of fuel. Drove 3 more hours and almost 200 miles without symptoms - check engine light still illuminated keeping me curious and fully alert along the way.

Got the codes pulled at a parts store that was open on Sunday. PO300 & PO301. Random misfires and cylinder 1 misfires. Sounds consistent with poor fuel supply? Spent the rest of the day searching forums for any clue to this highway stalling. All I came up with was to clear the computer - disconnect battery, turn lights on, wait 15 mins, reconnect battery, start engine, apply brake, drive, etc. This and another full tank of gas gave me enough courage to set out on my trip home.

Next occurrence was just outside of Santa Fe, NM. Similar conditions again: Hot day, AC kicking, Interstate travelling about 80mph, slightly loaded, climbing in elevation, fuel tank just below half - stalled out. Repeat previous learned routine. Open hood, vent gas cap, walk it off for 30 mins, return to truck, start it up. Drive to next town and top off with fuel about 30 miles away - only took 16 gals! Made it home 4 hours later without stopping. No repeat symptoms, no check engine lights.

The next day a code - PO420. Catalytic efficiency below threshold.

Quick recap:

6.2L gas engine stalling at hwy speeds.
Cruising between 65-80mph
-Interstate travel - no stops between last fillup and stall.
-Warm weather, AC on
-Running on bottom ~1/2 tank
-climbing in elevation, slightly loaded

To clarify: slightly loaded - no trailer, maybe 1,500 lbs bed cargo, mostly wind drag. The most I have pumped into the fuel tank is 29-30 gals or so. I assume I have the 34 or 35 gal tank. Never seen the calculated "distance to empty" below 40 miles.

View 10 Replies

Toyota :: Check Engine Light Went On And Need It To Pass Inspection

The mechanic told me the oxygen sensor needs to be replaced but it is not an essential item. Can this be bypassed in order to have the car pass. Its not a safety issue. My car is a 98 and has 147,000 miles on it. It leaks oil, power steering fluid, the heat does not always work and I am shopping for a new car and do not want to spend money on anything not needed

View 3 Replies

Infiniti - Qx4 :: 2000 - Can't Pass Inspection / Engine Light Is On

I've got a 2000 Infiniti Qx4 that I can NOT get to pass inspection. I replaced the engine at 130,000 miles, and since then I've had nothing but problems. I live in TN and I've got to pass emissions testing. The car drives/runs great, no problems. I'm down to code P1105 or something, MAP/solenoid valve... Or maybe it was P10107 or something. Anyways it means the MAF sensor is malfunctioning or I've got bad hoses or electrical connections near the intake. So I replace the MAF. Nope, check engine light still on. I replace the clips on the hoses for the MAF. Nope, still on. I check all the wires n all the hoses. Nope, light still on. Now my mechanic is going on about I might have a bad computer or it might not have accepted the new engine as it was from a different year (still a 3.3L V6 standard of the prior to 2001 model)? My mechanic has been at it for over 2 weeks trying all kinds of stuff but to no avail.

View 4 Replies

Passat (B6) :: Engine Knocking Noise When Enter The Freeway And Accelerated A Bit

I have a 2007 volkswagen passat 2.0 L...115000 miles. Yesterday I was entering the freeway and I accelerated the car a bit when I started hearing this noise on the engine. I will try my best and describe the noise as a knocking of metal on metal. I thought maybe is the oil and changed it.

Now today I was going up the hill and accelerated the car when the noise appeared again, it happened again a little bit later, again going up a hill. There is no noise when I drive normally or I accelerate and I am not going up a hill.

View 2 Replies

Avalon 2005-12 :: Engine Light On - Won't Pass Emissions Testing

My check engine light is on and I read the code with my obd and the problem catalytic converter is bank 1. Which is bank 1?

View 1 Replies

TrailBlazer :: 2004 - Check Engine Light Came On And It Would Not Run Pass 15 Miles Per Hour

My friend has a 2004 Trailblazer with a 4.2. He was driving it a few days ago and the check engine light came on and it would not run pass 15 miles per hour. He turned the truck off and re-started it. The light went off and the problem went away. The scan tool came up with an old code that that throttle body sensor was bad or the throttle body needed cleaned. We cleaned the throttle body and ran it and it ran fine. Now here is the problem. When the heater is on and the truck is at idle, the truck will idle at 2000 rpm, then kick back to normal then kick back to 2000 rpm and then keep repating this issue. If we shut the heat off, the truck idles fine.

View 5 Replies

Tiguan :: 2.0 VW Engine - Breather Valve Stuck Causing Oil To Enter The Cylinder / Misfires

We have a 2009 2.0 Tiguan with approximately 60,000 miles. About 6 months ago, the check engine light came on so we took it in and found out the breather valve was stuck causing oil to enter the cylinder and causing misfires. Had this fixed an about a week later, the car acted up again. Took it in and removed & reinstalled the intake manifold. Both pricey fixes. The dealership said it was a problem with the 2.0 engine design. Now we have taken it in again to a local shop who is now informing us we will need to replace the intake manifold. He said the same thing about the engine design. Our concern is that this problem will need to be fixed on a fairly regular basis. We really love the vehicle but cannot afford the cost of this maintenance if it becomes routine and are considering trading it in for a Passat.

View 3 Replies

Phaeton :: Car Stalls Out On Highway

Had experience today of 2004 W12 stalling out on the highway at speed. Turned on flashers and coasted to side of road.

Check engine light came on, and car was able to restart by using the twist to left and the to right to restart.

After about 500 yards, stalled out again.

Have fresh fuel, ( use same fuel in three other cars).

View 13 Replies

Sonata NF (2006-10) :: V6 Stalls While In Motion On Highway

2006 Sonata GLS 3.3L v6 ... Vehicle has 192,000 miles and generally runs well but has started stalling out on the highway. Seems like it stalls more when turning on an exit ramp or after going over a rough spot or pothole on the road but not always. Not sure if anything in particular leads up to it. The car stalls, the power steering and brakes become unresponsive, all the dashboard lights come on, and I have to pull over and stop completely to try restarting. Usually starts right back up but sometimes it takes several tries. Took it to AAA auto care but since they couldn't recreate the problem, they weren't able to identify the issue. They did say that their diagnostic equipment was unable to access/communicate with the on-board computer for the engine if that makes any sense.

View 2 Replies

Golf IV / Jetta IV :: The Engine Light Flashes / Car Stalls

When you give it a decent amount of acceleration it starts to hesitate and kind of jump, the engine light flashes it kinda sounds like it want to stall. I'm not to good with the turbo motors. The car is a 2000 golf.

View 6 Replies

Golf IV / Jetta IV :: Engine Sounds Like Its Working Overtime / Car Stalls

I drive a 2003 Golf 2.0 manual. I've had this problem happen to me four times in my year-and-a-half of ownership -- once about three months ago and three times today.

Whether at highway or city speeds (60+ MPH or 30 MPH, respectively), power to the accelerator cuts out without warning. The engine briefly sounds like it's working overtime (but it could just be my foot on the accelerator pedal) and the tachometer needle struggles to stay at the RPMs. In a matter of seconds, the engine stalls and the needle gradually starts to fall. I can't tell you how dangerous of a situation this is to be in: 65 MPH on the highway with vehicles all around you, your car chokes, and you're losing speed.

The first time this happened to me three months ago, I had to hit my emergency lights and pull over to the highway shoulder. Turning the ignition off, then on, and attempting to start the car didn't work. I thought I was in trouble. Then I removed the key and tried it again. It was successful. I got to my destination (my parent's home) and they recommended I go see their regular mechanic for an inspection. He told me that the problem could be low fuel in the tank, as I did at the time. When the car's fuel tank is at a certain angle, the fuel pump doesn't pump fuel properly, messing up the whole combustion, and causing the car to stall. This explanation fit the situation I was in perfectly, as the fuel indicator had just come on when it occurred.

Today, the fuel indicator was just above the last 1/8 -- no fuel warning light -- and the car stalls three times (once on the highway to work, once on the highway home with no shoulders to pull over, and once on city road). I had prior experience about this and drive a manual, so I have attempted each time today to re-start the car while at speed. It was a scary situation the second time today: 9:30pm, dark, modest amount of cars on the road, on a twisty highway with no shoulders (California Highway 110 between Downtown and Pasadena) where each time you turn the ignition off, the headlights go out, the steering wheel goes stiff, and you're decelerating. Fortunately, I dropped only 25 MPH to 40 when I got the car running again when I remembered to remove the key first before re-starting.

Needless to say, rather than wait two days to get cheap gas at Costco (b/c I work tomorrow as well), I went to the 76 near my home and filled her up . Hopefully, this situation will not happen again, as I will be a lot more diligent about keeping gas in my tank.

View 24 Replies

Golf IV / Jetta IV :: AEG Engine Constantly Stalls While Driving - No Diagnosis

2000 Jetta, 2.0 AEG engine with 220k miles, recently started intermittently stalling (about 15-20 minutes into my trip) while driving mostly on city streets but has also stalled on the freeway at 65mph. Fuel level is always > half full, verified against my tripometer. When it stalls, engine completely cuts off, all dashboard lights are all lit, and no power steering.

I have VCDS but know only enough to be dangerous My mechanic has no answers and I don't want to randomly throw new parts at this the car, hoping to resolve the problem. It's becoming seriously dangerous to drive, knowing it will die at least once on every trip. What's the chance the oxygen sensors need to be replaced ?

Symptoms

(1) Most of the time the engine just turns off, as if I turned off the ignition. Other times, I can catch the engine RPMs drop to ~300 and just hit the gas, which sometimes saves car from stalling.

(2) Immediately after it stalls, there is is rotten egg smell.

(3) Once stalled, the engine won't start back up again for at least 5 minutes. (turns over, but doesn't start)

(4) Confirmed error codes from VDCS: misfires on all cylinders and random

(5) Took it to my mechanic for diagnosis. They were unable to duplicate on a road test. Smoke test showed no vacuum leaks, road test monitoring data did not capture any additional faults, and found no faults running it heat soaked and parked. They captured sensor signal data and found no abnormal patterns. They feel replacing the O2 sensors is an expensive guess.

(6) Replaced the crankshaft position sensor after the car would not start at all, one morning. (discovered that the CPS tested at a faulty ~50k ohms). Bought a new one, installed it and it turned over immediately but the stall issue continues)

Fault Codes

Code:
18057 - Powertrain Data Bus
P1649 - 35-10 - Missing Message from ABS Controller - Intermittent
16684 - Random/Multiple Cylinder Misfire Detected
P0300 - 35-10 - - Intermittent
16685 - Cylinder 1
P0301 - 35-10 - Misfire Detected - Intermittent
16524 - Oxygen (Lambda) Sensor B1 S2
P0140 - 35-10 - No Activity - Intermittent
seen separately

Code:
16517 - Oxygen (Lambda) Sensor B1 S1
P0133 - 35-10 - Response too Slow - Intermittent

Note that I have been ignoring the ABS-related errors for 4+ years. (not a concern or priority). On the short list are ignition coil or crankshaft sensor. Both of which require my mechanic to replace, I think.

View 3 Replies

Ford - Taurus :: 2001 Stalls After 2 Hours Of Highway Driving?

This happened a year ago. We got it running after a few minutes, and had the fuel filter changed before continuing on the highway again. It ran fine for the remaining 2 hours of the trip. I looked online and saw this as an issue, but no one knows why. It was suggested to take a break after 2 hours, and that has worked until 2 days ago, when it stalled an hour after the break, then restarted after some time and made it the next 1 1/2 hours home no problem. Each time it stalled, the air temp had been in the high 90's.

View 2 Replies

Passat (B5) :: Bad Noise When Rev Or Drive After Floored Car In Reverse

I was being dumb and floored my passat in reverse. Now its making a really bad noise when i rev it or drive at all. It sounds like someone holding something against a moving tire or wheel or something. Not sure if its the tranny or a belt or what and there's a slight burning smell...

View 16 Replies