Golf/GTI VI :: 2010 TDI Started To Misfire When Going Easy On Throttle
My 2010 Sportwagen TDI has recently started to misfire. This only seems to happen when I'm going easy on the throttle. It also seems to happen after about 10 seconds after I've come to a stop and began moving again. It only appears to misfire once, then it goes away for a couple of minutes, then it sometimes returns. I haven't been able to track it to a specific RPM, speed, or gear, but it does seem to be more frequent around 1600-2000 RPM and about 30 mph. It feels more pronounced in the lower gears, but this is probably due to the gear ratio effect. There are no engine lights. I have not taken it in for a dealer scan. It has 32,000 miles, I always use name-brand diesel along with Diesel Kleen at every fuel up.
View 6 RepliesGolf - Volkswagen - Misfire :: 2003 - Engine Started Shuddering?
My engine started shuddering rather considerably a few days ago, seems to be misfiring. Happens both while idling and accelerating. Thought it could be a bad spark plug, and was prepared to replace them. Which is doable, but not easy, considering they're not very accessible with this particular engine. But when I lifted the plastic cover off the engine to take a look, I noticed this tube (circled in picture) had been worn away considerably in one spot. In fact, it's barely attached.
Now I'm no expert, but I've read that a leaking or disconnected vacuum hose can cause exactly the type of issue I'm experiencing. I'm wondering if the object pictured is in fact a vacuum tube. Might that be the issue? If so, how easy would it be to repair it myself? I'm not very experienced with making my own repairs, but I'm good with a set of tools, as long as I have instructions.
Prius (Gen 2) :: ICE Started And Misfire When Backing Out Of Driveway
I readied my Prius and was backing out my driveway. The ICE started and was misfiring very badly, sounded like it was barely running, making all kinds of clatter.
I stopped, put the car in park, and the idle was very rough, sounded like it was trying to clear itself from being flooded. There were no warning lights or blinking check engine lights, so I drove off.
Heres where things get freaky. If I accelerated any more than 1/4 of the gas pedal, the car would buck and the ICE would shut off completely. Then when I let go of the gas, the ICE would start back up. If i feathered the gas lightly, the ICE would stay running. After the car warmed up, this behavior disappeared.
Toyota - Tundra :: Intermittent Misfire Only When Engine Is Started And Cold?
2008 Tundra 5.7 only 55K miles – What is causing an intermittent misfire at startup? It’s been running great, then 2 weeks ago when I started it up I could feel a misfire. By the time I backed out of the driveway the check engine light came on. This is what I have learned so far:
•It only happens when you start the engine and the engine is NOT at operating temperature.
•The engine code always reports misfire on Cylinder #2 I put in a new plug and swapped coils but it still reports the misfire on cylinder #2.
•Once it starts to misfire it will continue to misfire until the engine is at operating temperature and you restart the engine. NOTE: You MUST restart the engine for the misfire to go away. It will be running rough, turn engine off/on once it is at operating temperature and it's as smooth as can be, no more misfire.
•One time I started the truck, I felt the misfire and drove it to a parts store to read the code. Engine was fully warm by the time I reached the parts store. I did not power off the engine, plugged in the tester and read the code which was a misfire on cylinder 2. I cleared the code and within 2-3 seconds it logged the misfire on cylinder #2 again. Cleared the code several times and it kept reporting misfire on cylinder 2. You could also feel the misfire happening. Turned engine off, started it right back up, like before no misfire, cleared the code and it no longer reported a misfire.
•This just started intermittently happening. This morning it happened again, I drove it for about 5 min, engine was about 75% it’s normal operating temperature, powered it off/on, still had the misfire. Once engine temp reached normal temp (about 9 min), I turned off engine, started it back and like before problem was gone.
What is causing this to happen?
Ford Excursion :: New Starter - Misfire / Started For A Split Second And Stalled
Well It has been an expensive month for my Ex. New starter, Then a miss-fire. I ended up replacing all 10 plugs, and all 10 coils and I got ford coils.
Today I got in it, hit the ignition. It started for a split second and stalled. Went to go fire it up and well, its turning over faster then usual like its not getting any fuel or something. Now I am at the mercy of a local town shop, because the tow to the shop I run is about 450.00. I am thinking its the fuel pump... But we will know shortly.
Ford Ranger / B-Series :: Misfire Codes Started Out On Cylinder 5
I am currently chasing misfire codes that started out on cylinder 5 p0305 was the first code I replaced spark plugs and wires about 200 miles the code returned checked coil with meter it was barley in spec. I have replaced coil same code only difference was a hard start cold or hot replaced injectors now hard start is fixed but logging codes for right bank is to rich and p0300 304 305 and 306 also performed compression test on right bank and readings are 155 155 and 160...
View 3 RepliesImpreza :: 2000 2.5RS Misfire - Check Engine Light Came On Again And Started Flashing
I've got a problem with a 2000 Impreza 2.5RS 5spd. It started with the check engine light coming on. A trip to Auto zone revealed that the O2 sensor was the problem. But on the way home, the light came on again and started flashing. All the while the car started acting like it had a misfire. It idles really rough and the exhaust smells like it's running really rich. I've replaced the plugs and wires, and all corners of the ignition coil check out properly as well. Can the O2 sensor cause a misfire in one or more of the cylinders? Or is something else that I should be interrogating as the cause?
View 5 RepliesCaprice :: Check Engine Light Started Blinking - Multiple Misfire
I have a 1996 chevy caprice wit a 4.3 v-8 one day i was driving and the car started acting funny and the check engine lite started blinking i had the codes read and 0p300 came up saying multiple misfire so I changed the plug wires they all connect in the front around the harmonic balancer well that didn't work its still saying multi misfire so I took a spark plug wire off of the electric dis block and no change in motor now I don't know what to do...
View 5 RepliesCaravan/Voyager :: 1996 Van Started Chugging - Random Misfire / Bad Cylinder
Last week, my van started chugging and the keydance code indicated random misfire. I changed the front spark plugs and wires and it ran a little better but still showed the error. Took it to my trusted mechanic and he changed the back 3 wires and plugs and the coil pack. Code now showed misfire on one of the back cylinders(I forgot which one). 2 Mechanics both confirmed good spark and gas at the cylinder. He is saying that there is a mechanical problem in the cylinder and the fix would be over $1k.
The van has over 250k on it so it's not worth the engine work. I asked about a compression test and was told that it's almost impossible to test the rear cylinders without doing a ton of work, and that they are 95% sure that it is a mechanical problem with the cylinder. I've known the mechanic for over 20 years and he is an honest guy, and knows that I won't do the expensive repair, so he's not trying to rip me off.
I don't have the facilities or knowledge to do the work, so it looks like I'm screwed. Is there anything else that I should be doing before I write the van off? It does run, but very rough at low speed, and no power at high speed, and mech says that the unburned gas will eventually screw things up.
Accent LC (2000-05) :: CEL Came On / Cylinder 4 Misfire - Exhaust Started Sounding Loud
I just bought a 03 accent the same day i bought it the CEL came on got it read and it was cylinder 4 misfire. took it to the garage the dealer i bought it from takes it to he said there was a little water around the boot in that weird little channel area under the cover he said he cleaned it up dried all out then reset the code and it was good, for a little about 2 weeks later it comes on again i get it read and it says cy 4 misfire again but also P0133 (o2 sensor bank 1 sensor 1) and i cannot remember exactly but i think the CEL came on after the exhaust started sounding loud, like it has one of those ricer mufflers on it.
Well I jacked up the car today and looked the only thing i saw was after the first cat right before the braided flex pipe there is this weird "shield" looking piece on the underside of the exhaust pipe dunno if its really supposed to be there or what it is for but from somewhere under that piece i can see exhaust coming out(its cold right now) also the flex piece is kinda blackened like its had exhaust fumes blowing on it for a while. i cant imagine why this would be a normal thing but i have never worked on hyunda before. i am thinking if there is some sort of "leak" there that is why the o2 code is showing. i am stumped, esp on the cy 4 misfire all sparks and wires look good i pulled each wire with it running and it bogs down til i plug it back in.
Santa FE SM (2001-06) :: Car Started To Stumble - Random Misfire Related Code
I recently noticed while driving my Santa fe the car started to stumble.Then a little while later the check engine light came on. Pulled the code came up with p300. It's a random misfire related code.
View 3 RepliesGolf IV R32 :: Interior Lights Started To Dim / Headlights Started To Flicker
so on my way home the interior lights started to dim then out of no where the abs and traction light came on as soon as i pulled up to my house the headlights started to flicker radio shut off gauges flickered off and climatronic shut off now the cars dead would this be the alternator? Car is vf stage 2 supercharged....
View 22 RepliesCaravan/Voyager :: Check Engine Light Came On And Started Blinking - Random Misfire
I have a 96 Grand Voyager that had had sat for a year undriven or started due to being out of state. It ran like a champ when I parked it. Now I charged the battery and went for a drive on the freeway and my check engine light came on and started blinking. I had the code read it came back with 2 codes a P0306 and a P0300. I noticed that the cylinder 6 spark plug wire was arcing on the core support. So I replaced all the plug wires and spark plugs with Champion platinum spark plugs. I cleared the codes and took it on a test drive and the P0300 code came back. Is there anyway the old gas is causing the random misfire? or what else could it be?
View 1 RepliesAccent MC (2006-11) :: 2008 - Car Started Jumping And Being Sluggish / Random Misfire Codes
I have a 2008 Accent Hatchback with 130k+ miles. I got a pretty good deal on it from a fellow who maintained pretty good service and had installed an aftermarket air intake (well, he removed the stock one and put a small, roughly 4" diameter, filter that is open to engine compartment) and all looked pretty good.
At the first fueling, I noticed issue - I had to rev motor for about 30-45 seconds to get it to stay started. Figuring it was an evap issue, I replaced purge valve and gas cap (cap was obviously loose). This did not correct the problem. I did not worry about it to much because with that exception, the car drove wonderfully back and forth to work, etc.....until recently.
Car started "jumping" and being sluggish. Codes came back as random misfire. Plugs and wires are only a few months old. I wondered if it had something to do with fuel so I ordered filter and pump (figured i would replace both since I was going to be pulling top off tank anyways) - this is going to be my project for the day.
Here is the kicker though : I noticed in the past day or so that car has been okay on my short commute to work in the morning and back home in evening. When I went to store midday and was parked on HOT pavement, I had issues right away. Car is very temperamental as the temperature increases. My wife also noted that last night while driving about 15 minutes away that the engine wall was hot enough to be uncomfortable to the touch of her bare foot and issues were abundant.
Once I get to speed in 5th gear, I seem to be okay, no issues (yet). It is primarily during acceleration and mostly during low RPM (low for this car anyways which seems to run best at 2500+).
Ford - Taurus :: 2005 Started Running Rough - CEL Came On / Cylinder 5 Misfire Detected
My wife's car suddenly started running rough. 2005 Taurus, 6 cyl, 3L, OHV, 83K miles. CEL came on and code came back as "P305 - cylinder 5 misfire detected". As a side comment, her tachometer has been fluctuating big of late as well.
View 2 RepliesFord F-150 (2004-2008) :: MIL Light Started To Flash / OBDII Codes / Misfire
My wife was driving her truck yesterday and said the MIL light started to flash and the truck felt like "it was about to blow up" . So when I got home I busted out the trusty old scanner and this is what I got:
P0305- Cyl 5 misfire'
P0354- Ignition coil D primary/ Secondary circuit malfunction
P0304- Cylinder 4 misfire
The truck is a 2005 5.4 with ~130,000 on it and it runs very well for the most part. I have done the spark plugs before the summer and replaced them with the motorcrasft sp-515s. I am guessing the problem will be with the #4&5 coil packs. is there a way to troubleshoot these?
Ford F-150 - 1997-2003 :: Truck Randomly Started Missing - Misfire On Both Cylinder 1 And 8
I've got a 97 f150 4.6 that has randomly started missing over the last month. It has started to get more frequent and codes are showing a misfire on both cylinder 1 and 8. Both of these cylinders run off the same coil pack. I'm thinking its the coil? The plugs and wires, motocraft, have about 3k on them and the truck runs great otherwise. I just don't know how common a coil would cause this or if they would act intermittent like this.
View 5 RepliesFord - F150 :: Check Engine Light Started Flashing / Cylinder 4 Misfire Code
1997 Ford F150 - 133K Miles - 6cyl - 4.2L. This is a truck that gets less than 2K/year put on it. Has had "issues" with worn bearings and holding oil pressure for a few years now. Yesterday, the check engine light started flashing (as opposed to solidly lit) and the code came back as a cylinder #4 misfire (only the one code). The truck was clearly not firing on all cylinders and at idle, ran terribly (couldn't be driven). I just did a compression test on all the cylinders and all measured around 140-145psi except the #4 which read almost 170psi. I rechecked this a few times as well as a couple of the others and am now sure of the results. What could cause this one cylinder to have a higher compression ? Is whatever is causing this increase in the compression, also be the cause of them misfire ?? I'm stumped here and quite frankly, expected the compression on the #4 cylinder to be really low as opposed to the others.
View 13 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 Misfire / Engine Started Missing Out And Vibrating Very Bad
I've got an issue with my truck, I was towing home my camper this weekend and my engine started missing out and vibrating very bad, then it overheated... pulled over and check codes, p0263, p0299, p0300, p0301. Oil all over engine, tons of blow by, definitely a dead miss on cylinder 1. Smokes bad out of exhaust, zero power, and blows cap off of oil filler when loose, tons of smoke and oil from ccv.
My question is, could it be in the valve train? Or is it going to lie in the piston/rings? Blown head gasket? It did overheat, but didn't puke out of bottle, turbo timer kept it running for a bit after I shut it down roadside, egts were definitely high. Also the egr is deleted, have a predator programmer with custom tune for she delete.