Golf V R32 :: 2008 - Installing Staggered Wheels?
Can I put 20" staggered wheels on my 08 r32?
View 24 RepliesGolf/GTI VI :: How To Rotate Wheels With A Staggered Set Up
Just got a set of staggered wheels (first set) they are 19x8.5 and 19x9.5. Just wondering if you actually rotate the wheels or how you go about doing that?
View 13 RepliesGolf IV R32 :: Staggered Wheels And Rear Differential
It was brought to my attention that staggered wheels Can blow out the rear dif? Is this common? I currently have 18x8 and 18x9 rear summer wheels and I haven't seen any issues occur yet.
View 12 RepliesTouareg :: Turn Off TPM System After Installing New Wheels
I installed new wheels and the TPMs do not fit. Is there a simple way to turn off the TPM system? Or do I have to go to the dealer?
View 3 RepliesPrius (2010-12) :: Resetting TPMS Light After Installing Snow Tires On OEM Wheels
I tried to reset my TPMS light using the procedure in the owner's manual after installing my snow tires on the OEM wheels. Now it looks like there is no effects as the lights will just keep blinking even if i am holding the button down. Does this mean the tire shop broke one of my sensor during the install?
View 5 RepliesGolf/GTI VI :: Flutter After Installing New DV
I installed the pierburg revised DV yesterday because my old DV was shot, squealing and leaking boost. After installing it I noticed that when i'm under around 15 psi and i let it build up that I get this flutter I didnt have before. I assume its the wastegate but I haven't heard it prior to installing the new DV so my fear is that its the valve no circulating and its putting the unused psi back through the turbo (not good).
View 7 RepliesGolf VI R :: After Installing HPFP Car Throws A CEL
-I currently have a CTS turbo intake, 42DD turboback and installed the Autotech HPFP. After we installed the HPFP and drove around the block I threw a CEL. (not sure the exact code # ) but it was related to the cam shaft.
We were unable to upload the 2+ tune because his computer which has his APR info is under repair. My guess is that I am throwing a CEL because I upgraded the HPFP but do not have a tune for it yet. Who else has installed a HPFP before getting the tune?
Golf IV / Jetta IV :: Installing Fog Lights
So i have been looking to get some new headlights with the projector housing but noticed that most of them have a fog light which my car does not have. I know in order to get them to work properly i would need the euro switch, but would i need to run additional wires through the firewall?
View 8 RepliesGolf/GTI VI :: Installing 20mm Spacers
I have a 2013 gti. Lowering it in h&r super sports. I want some spacers to complete my look on the 50000km a year Car. Would 20mm spacers all around be to much?
View 2 RepliesGolf V R32 :: Installing Tampa Mod Resonator
Got my Magnaflow resonator in the mail today. Called up my exhaust shop and they are willing to tackle it but were wondering "where to cut" and "what about the internal baffles". Do you cut and shorten the center of the resonator by 7 inches or do you cut at one of the ends and shorten it from there 7 inches?
The picture I saw on TampaVW's thread shows it having been rewelded from the exit side (IIRC) but what about the internal baffles?
Golf V R32 :: Installing H&R Rear Sway?
So tonight I got the chance to install my H&R Rear sway bar on my car...let me start off by saying I was lucky enough to have a lift, air tools, all the correct tools, etc...now the frustrating part...i opened the box saw the bar and new bushings, figured this should be 100% straight forward 10 min job... the old bar came out in about 3 minutes...then I got the new bushings on the H&R Bar and went to put the factory brackets on...they wouldn't fit even close. Luckily I had a press so I pressed them on. Once I got the bar in the car I got the two top bolts started and could not for the life of me get the bottom two...its like they were 1/4in to low... Was I missing parts from H&R? also the factory caps/brackets seemed to sit off to the side of the new H&R bushings and there was no way to line them up straight, but I finally got everything on there..
View 18 RepliesGolf V R32 :: Rear Fog Icon Popped Up After Installing LED
I installed my LEDs put in the fog trigger wire, did the vag com, and on my dash the rear fog icon pops up. BUT no rear fog, I still have a bulb out message as-well. I've triple checked all of my wiring today, and did not see anything wrong. I've tried replacing the bulb.
View 17 RepliesGolf IV R32 :: MAF Code P1143 Since Installing Stage 2 VF
Since I installed the Stage 2 VF I've been getting the p1143 code for my maf. I've tried two different maf's and the problem keeps coming back.
View 3 RepliesGolf IV / Jetta IV :: Installing Short Shifter?
There is only one DIY i can find that is still alive. I have a megan short shifter. Its already half way in. I just don't have any instructions and i am kind of at a loss as to where i go from here. Does this shifter change the way my reverse gear will be engaged? I mean will i need to pull the trigger up to go in reverse or will i still push down? Does the spring that came with the kit go under the sleeve or above it? Sounds confusing.
View 3 RepliesGolf IV / Jetta IV :: Installing ECS Skid Plate
How to install rivets to the subframe and rails of the car I can't figure it out to save my life and it just says to put the ecs bolt and but rivet installer but it literally does nothing the rivet literally slides in and out am I missing something.
View 16 RepliesGolf IV R32 :: Installing New Bumper - Screws And Nuts?
Brand new bumper came in without screws and nuts, it's ready for painting but i need the right hardware. (photos are simply for reference)
I want to keep the screws and nuts OEM meaning as close to as exact as possible without home depot or some lame arse hardware store, i'm talking about original VW if possible parts. Or at least the clips if anything at all. VW dealer hasn't supported much either, they just said go to Home Depot and buy some regular screws and u-nuts but I want everything as if it came straight off the dealership. I do not believe that all screws and nuts are created equal and where to get exact right hardware I need.
As far as I know the bottom needs 18 or so 5mm nuts and "u-nuts" that they screw into. And there's also the stock scoop, where to even start with screws on this one.
Golf IV R32 :: Passenger Strut Won't Come Out When Installing Coilover
The strut is lose, I can spin it hardly but I can't get the rotor to go down far enough, already disassembled the control arm but it didn't do much considering I couldn't move it forward or backward so the rotor still sits on a corner or the arm. I did the drivers side already.
View 3 RepliesGolf IV / Jetta IV :: Installing 18x9.5 With 35 Mm Offset
I'm looking at some wheels and the specs are 18x9.5 with 35mm offset, will it poke out or no? I can get them staggered but I would rather not?
Car is a 02 Tdi Golf 4 Door
Golf V R32 :: Car Not Sitting Level After Installing New Dampener
Installed a new dampener on the front passenger side. As soon as we lowered it off the jack it was higher. Pulled out of the driveway and lowered a bit, drove around the block settle a little more.
Now, three days later, it is still not level. Do I just need to keep driving it and let it settle? Will it not settle as low as the other because it is brand new and the rest of the kit is a year old? If so is the best thing just to just play with the other three corners till its level?