Santa Fe (DM - 2013+) :: Loose Screws / Nuts In Wheel Wells
I just completed a detailed cleaning of my SF last weekend and I noticed that every plastic screw and plastic nut inside the wheel wells were all loose. (Not the screws on the outside but inside above the tires.) I tightened them only finger tight.
View 3 RepliesCamry 2012+ :: SE - Part Number For Screws That Hold Front Bumper?
I took apart my front bumper for my 2012 Camry SE a while back and swapped it when I hit a cone on the freeway.
I accidentally lost one of those metal nuts that goes underneath the bumper - its like a hexagon if I remember correctly. - I had to use a torque wrench to open them and there was like 8 or 10 total.
Camry :: Installing XLE Bumper On LE For Fog Lights?
Is it easy, I see that LE Camrys are pre-wired for fogs.
View 14 RepliesPrius C :: Installing Reverse Sensor On Bumper
I am installing aftermarket reverse sensors on my bumper , do i need to take off before drilling or should be ok if nothing is behind, how to remove the rear bumper.
View 5 RepliesTouareg :: Installing Reflector On Right Rear Side Of Lower Rear Bumper?
How to remove/install a reflector on the right rear side of the 'lower' rear bumper? I don't see any screws. So, can I pop it out with a screwdriver? Or, is it attached from the inside?
View 2 RepliesPassat (B5) :: 2002 - What Torque The Screws From Oil Pan Should Be
I'm going to work with my cousin change his oil pan on his 2002 passat 1.8T and I would like to know what torque the screws from the oil pan should be? Is the anything specific that I must know about doing this? Anything to make the job easier, faster and to not make mistakes.
View 3 RepliesTires - Repair - Wheels :: Overtightened Lug Nuts
I took my car to my usual trusty mechanic. Trusty asked where I had had the last rotation done. All the lug nuts were overtightened. The manual says to tighten to 96 pound-feet (that’s a measure of torque).All the nuts were tightened well past this. Many came loose at 200 foot-pounds. More at 300 foot-pounds (that’s as high as they wanted to go with their pneumatic torque wrench). There were still 5 nuts that didn’t budge. They brought out the manual torque wrench and muscled 4 of those loose. But one on the left rear wheel wouldn’t come loose.
So they made it a 3-wheel rotation, and left the left-rear wheel in place. I had a puncture driving over a piece of road junk last spring out of state and had to buy a new tire. Clearly the people at Roadside Tire had no clue (although why they messed with the other three wheels is a mystery. But although the left rear is the newest tire, i still don't want to have to trade the car in when the tire is worn! Nor do I want to trash out the rest of the assembly. What to do?
Ford - Ranger :: 2010 - Rusty Screws On Floor Boards
Why can't ford use stailess steel sheet mental screws on the floor trim pice where door meets car. My 2010 Ranger the screws on taht trim piece have rusted already and I have drill them out and replaced them. In order to clean under the floor matting or remove trim piece. .
View 3 RepliesHonda - Pilot Cargo :: 2003 - Hatch Lock Screws Fell Out
The lock in the cargo hatch of my 2003 Honda Pilot is loose and wobbles around -- you have to really slam the door hard to get it to engage, and it rattles. I went to Autozone and showed it to them, and the guy pulled the trim molding out slightly and retrieved two short screws with large flat heads. Said I needed to remove the trim panel and put the screws back in. So -- how do I remove the trim panel so I can do this? Do I need specialized tools, and is this something I can do myself?
View 2 RepliesPrius (Gen 1) :: 2003 - Clicking Noise Coming / Nuts Missing
So I first heard a clicking noise last week but it got worse this morning. Half-shafts? Wheel bearings? 165,000 miles on original brake pads.
I turned around and dropped the 03 Prius at the dealer and asked for a diagnosis:
Two lug nuts missing. One lug nut finger loose.
Ford F-150 (2004-2008) :: Loose Front Wheel But Not Lug Nuts?
I was driving my truck and I heard a noise around the front drivers side wheel area, like a loose center cap. I got home and jacked up the wheel and grabbed it, it wiggled side to side and u and down. Would that be wheel bearing or tie rod end or something else
View 11 RepliesSonata NF (2006-10) :: Brakes Heating Up To The Point That Lugs Nuts Are Hot To Touch
Just wondering if this is normal or not. I have a 2007 Sonata GLS. Recently I replaced the front and rear pads with ceramic pads and new rotors in the rear. My question is, is it normal for the brakes to heat up to the point that the lugs nuts are hot to the touch. As far as I know I am not doing any hard braking just normal driving in the city. But when I touch the rims and especially the lugs, they are hot and can burn to the touch. Is this because of the ceramic pads?
View 14 RepliesFord Excursion :: Rear Shock Bolts And Nuts - Part Numbers?
I've noticed quite a few threads looking for the shock bolts lately. I've replaced one of mine and just had another break. Today I ordered replacements for all 4 nuts and bolts.
The Bolt part number is - N605906-S2
The Nut Part Number is - N803714-S426
Golf/GTI VI :: Flutter After Installing New DV
I installed the pierburg revised DV yesterday because my old DV was shot, squealing and leaking boost. After installing it I noticed that when i'm under around 15 psi and i let it build up that I get this flutter I didnt have before. I assume its the wastegate but I haven't heard it prior to installing the new DV so my fear is that its the valve no circulating and its putting the unused psi back through the turbo (not good).
View 7 RepliesGolf/GTI VI :: How To Remove The Front Bumper
I have took off the screws in below pictures. But the bumper seems still stick on the car body. Any screws are missing? Or other issue?
View 4 RepliesGolf VI R :: Front Bumper Removal?
I'm having trouble removing the front bumper. Does it remove like the GTI or is it different? I don't have the confidence to pull harder without knowing.
View 2 RepliesGolf VI R :: After Installing HPFP Car Throws A CEL
-I currently have a CTS turbo intake, 42DD turboback and installed the Autotech HPFP. After we installed the HPFP and drove around the block I threw a CEL. (not sure the exact code # ) but it was related to the cam shaft.
We were unable to upload the 2+ tune because his computer which has his APR info is under repair. My guess is that I am throwing a CEL because I upgraded the HPFP but do not have a tune for it yet. Who else has installed a HPFP before getting the tune?
Golf IV / Jetta IV :: Installing Fog Lights
So i have been looking to get some new headlights with the projector housing but noticed that most of them have a fog light which my car does not have. I know in order to get them to work properly i would need the euro switch, but would i need to run additional wires through the firewall?
View 8 RepliesGolf/GTI VI :: Installing 20mm Spacers
I have a 2013 gti. Lowering it in h&r super sports. I want some spacers to complete my look on the 50000km a year Car. Would 20mm spacers all around be to much?
View 2 Replies