Lexus SC430 :: 2002 Hard Steel On Steel Knock Sounds In Front
I have had my struts replaced at local gas station. Unfortunately, there is now an occasional hard steel on steel knock in the front. Very weird indeed.
Is there something they may have missed when they installed them?
Golf V R32 :: Steel Rattle Right At The Shift / Exhaust Loose?
Everytime I run my revs past 4 and shift, I can hear a steel rattle right at the shift. It's stock exhaust btw, no mods...
View 24 RepliesFord Super Duty (1999-2016) :: 2007 - Stainless Brake System?
I want to change out the whole system for stainless on a 2007 superduty. I got stainless lines and braded hoses for it. I'm ordering stainless fittings. (I got a flare tool) The braded hose kit i got has two hoses for the front and one drop hose for the rear. When I looked underneath the rear, I see the rear discs have a short hose that hooks to the caliper. or stainless braded hose?
Also, stupid question. Does the front resivoir go to the front brakes? The reason I ask is the front fitting is smaller. Seems like the big fitting would go to the front.
Trans Sport :: ELC Exhausts Air When Key Is Off?
My Haynes manual indicates that the ELC exhausts air when the key is off. Is it intended to exhaust all air from the shocks every time I stop? It doesn't make sense to lower the vehicle every time I stop for fuel etc. With over 200k miles on this can it's amazing that the compressor still works.
View 9 RepliesMusty Smell From AC / Fan Exhausts Every Time When Start The Car
When I start my car after its been sitting overnight, I get a musty smell arising from the AC/fan exhausts.... it dissipates shortly but it happens almost every time.
View 1 RepliesFord F-150 (2004-2008) :: How To Remove Seized Exhausts Clamps
I just got my new roush catback exhaust and I seem to have run into a wall in the installation. I cant seem to take out the factory hangers.
View 2 RepliesCamry :: Factory Steel Rims Always Really Hard To Get Off?
My friend has an 07 Camry with the factory steel rims and they are always such a pain to get off. They never come off easy at all. I bang & bang & bang on it lightly on the tire & on the rim & after a few mins it will come off. It is always like this on all 4 tires! The first time I worked on his car all 4 tires were stuck on good, and it took me almost 45 mins just to remove the 4 tires. So before I put them back on, I cleaned up the rust and I put some anti-seize around hub snout and still they are pain to get off. I have other cars with steel rims and they all come off easy..Why such a pain with the 07 Camry steel rims?
View 2 RepliesGolf/GTI VI :: Flutter After Installing New DV
I installed the pierburg revised DV yesterday because my old DV was shot, squealing and leaking boost. After installing it I noticed that when i'm under around 15 psi and i let it build up that I get this flutter I didnt have before. I assume its the wastegate but I haven't heard it prior to installing the new DV so my fear is that its the valve no circulating and its putting the unused psi back through the turbo (not good).
View 7 RepliesPrius (2010-12) :: GEN III Slight Shimmy On Steel Bridges
When traveling over bridges that have a ribbed steel ramp over the draw portion of the bridge, my 2012 Gen III does a slight shimmy.
View 3 RepliesGolf VI R :: After Installing HPFP Car Throws A CEL
-I currently have a CTS turbo intake, 42DD turboback and installed the Autotech HPFP. After we installed the HPFP and drove around the block I threw a CEL. (not sure the exact code # ) but it was related to the cam shaft.
We were unable to upload the 2+ tune because his computer which has his APR info is under repair. My guess is that I am throwing a CEL because I upgraded the HPFP but do not have a tune for it yet. Who else has installed a HPFP before getting the tune?
Golf IV / Jetta IV :: Installing Fog Lights
So i have been looking to get some new headlights with the projector housing but noticed that most of them have a fog light which my car does not have. I know in order to get them to work properly i would need the euro switch, but would i need to run additional wires through the firewall?
View 8 RepliesGolf/GTI VI :: Installing 20mm Spacers
I have a 2013 gti. Lowering it in h&r super sports. I want some spacers to complete my look on the 50000km a year Car. Would 20mm spacers all around be to much?
View 2 RepliesGolf IV R32 :: Installing Staggered Wheels
I'm interested in installing a staggered set of wheels on the R. The size I'm looking are 18x8.5 and 18x9.5. My question is what wheel sizes should I run to keep everything within spec of my Haldex unit? Ive read about staggered units having to be within 3 or 4% so nothing breaks down prematurely.
View 24 RepliesGolf V R32 :: Installing Tampa Mod Resonator
Got my Magnaflow resonator in the mail today. Called up my exhaust shop and they are willing to tackle it but were wondering "where to cut" and "what about the internal baffles". Do you cut and shorten the center of the resonator by 7 inches or do you cut at one of the ends and shorten it from there 7 inches?
The picture I saw on TampaVW's thread shows it having been rewelded from the exit side (IIRC) but what about the internal baffles?
Golf V R32 :: Installing H&R Rear Sway?
So tonight I got the chance to install my H&R Rear sway bar on my car...let me start off by saying I was lucky enough to have a lift, air tools, all the correct tools, etc...now the frustrating part...i opened the box saw the bar and new bushings, figured this should be 100% straight forward 10 min job... the old bar came out in about 3 minutes...then I got the new bushings on the H&R Bar and went to put the factory brackets on...they wouldn't fit even close. Luckily I had a press so I pressed them on. Once I got the bar in the car I got the two top bolts started and could not for the life of me get the bottom two...its like they were 1/4in to low... Was I missing parts from H&R? also the factory caps/brackets seemed to sit off to the side of the new H&R bushings and there was no way to line them up straight, but I finally got everything on there..
View 18 RepliesAcura - Legend :: Steel Hammer Type Noise From Under The Hood
I have a 91' Acura Legend (lots of miles 179K) and makes a sound of a sick lion/ steel hammer. When I turn it on, automatically it rev's the RPM's to 1.5-2000, and I will usually wait a few minutes before it reduces RPM. When I put it in any gear it will make a pound (like steel) from the hood. When in drive I have to slowly accelerate or the pop continues then follows with a sick almost grinding (like a Lion has a sore throat)sound. If I barely push on the accelerator it will drive slightly normal or (sometimes) slam on the gas. What do you think?
View 3 RepliesFord F-150 (2009-2014) :: 2012 - Replacing Steel Wheel?
I just inherited a 2012 F150 Fx4 Super Crew. Nice looking truck, but the wheels are stock 17" steel. Need upgrading to nicer looking wheels/wheel covers w/o breaking the bank?
View 14 RepliesGolf V R32 :: Rear Fog Icon Popped Up After Installing LED
I installed my LEDs put in the fog trigger wire, did the vag com, and on my dash the rear fog icon pops up. BUT no rear fog, I still have a bulb out message as-well. I've triple checked all of my wiring today, and did not see anything wrong. I've tried replacing the bulb.
View 17 RepliesGolf IV R32 :: MAF Code P1143 Since Installing Stage 2 VF
Since I installed the Stage 2 VF I've been getting the p1143 code for my maf. I've tried two different maf's and the problem keeps coming back.
View 3 Replies