Ford - Ranger :: Stalling Out When Cold - Cylinder 4 Misfiring
I've got a 2000 Ford Ranger, manual 4 cyl. When cold, she's been stalling out. It happens very reliably when I come to a stop and put it in neutral (or put the clutch in). Only when she gets warmed up does it stop. Check engine light has been on (for a long time) saying the TPS sensor is out and the 4 cyl. is misfiring. I replaced the TPS sensor and it had no effect on the problem. A friend recommended changing the oxygen sensor.
View 5 RepliesGTI 337/20th Anniversary :: Misfiring When Flooring - CEL Comes On And Flashes
I have had my 337 for about 5 months now and occasionally when i floor it it misfires or something because the CEL comes on and flashes. This happens quite often and i was wondering if it is normal or what it could be. Brand new spark plugs. coilpacks not so long ago.
View 4 RepliesGTI 337/20th Anniversary :: Misfiring / Car Running On 3 Cylinders
A couple of months ago I replaced my coils because of misfires. Just yesterday I satarted getting the running in 3 cylinders feeling. So I was woundering why they went out so fast? (Coils were from my brothers 20th gti)
View 5 RepliesGTI 337/20th Anniversary :: Idle Fluctuates From Almost Stalling To 1000 RPMs
I have a pretty bad flex pipe leak on my 20th. Would this leak cause a very rough idle almost stalling when I come to a complete stop. The Idle fluctuates from almost stalling to 1000rpms.
View 1 RepliesGTI 337/20th Anniversary :: 02 - Slave Cylinder Blew Out
3 weeks ago my slave cylinder blew out in a big way so I limped it home and into the garage and onto jack stands. After tearing out the gearbox, replacing the clutch and slave, we get the thing all buttoned up and start to bleed the clutch.
We feel as though we were making progress but upon pressing the pedal it stopped halfway to the floor, pressing harder now it would go to the floor slowly, then we start to hear the dripping again coming out of the bell housing. If we push on the pedal now, it goes half way down and stops, if you keep pushing harder you can tell that we are just pushing the fluid out at the slave cylinder and it start dripping hard again.
GTI 337/20th Anniversary :: Cylinder Misfire Codes For OBDII?
I changed my sparkplugs and coil packs last month. Was getting CEL light but it would go away after a while. I figured out that I had gapped my spark plugs way to small (almost touching) so I took them out two nights ago and regapped/ reseated them.
My car was running fine yesterday, but today when I started my car up, the engine was shaking a lot for about 10 seconds and the CEL was blinking. After 10 seconds the shaking and CEL went away...
It drove fine. I'm just wondering what could be throwing these CEL's and causing the shaking? Plugs are gapped to 0.32
Also, I had my timing belt and water pump replaced almost two weeks ago now. Any chance that could be lending to the problem?
My guess is that one or more cylinders are screwy. I'd rather not bring it into the vw mechanic since I'm tight on cash.
GTI 337/20th Anniversary :: Rough Idle - Car Get Close To Stalling When Falling From High RPMs
Just checking in to see where you'd recommend to start looking for a rough idle issue. It seems to get worse once the car fully warms up. I took a vid, and although it may not seem horrible in the video, it sometimes causes throttle lag from a stop and causes the car to get close to stalling when falling from high RPM's. Take a look at the video .....
View 2 RepliesGTI 337/20th Anniversary :: Flashing Engine Light - Misfire At Cylinder 2 And 4
Driving the other night I ran drove over a pot hole going about forty pulled up to the stop light and my car starts to make funny noises, barley got the car moving again but managed to get home. I hooked my computer up to it and it says misfire at cylinder 2 and 4.
View 14 RepliesGTI 337/20th Anniversary :: Engine Failure While Driving - Cylinder 1 Misfire
I am having this failure in my engine that is making me crazy while I am driving. Yesterday i took my car to a shop to see what was it. my MAF was gone ( I replaced it ) and the failure still going on. The mechanic connected his computer in my car and we went for a ride. HE told me cylinder 1 misfire.
This is what i did.
-change spark-plugs position (failure still)
-change coilpack (failure still)
What can i do ?
-clean injectors
-check for any carbon in valves
GTI 337/20th Anniversary :: 2004 GLI 1.8T - CEL Came On / Code P0303 Cylinder 3 Misfire
So I have a 2004 Jetta gli 1.8turbo and my CEL came on last night from normal driving, after it came on it still drives the same. I had it scanned for codes and got the p0303 cylinder #3 misfire. wondering what could be the solution for this? I dont think its the coil pack because I had them changed at the dealer from the recall about 2 months ago (anyway to check?) Also I have 97,000 miles on my car and my last oil change I used 0w-40 oil. I know this is probably not the best oil to use at this mileage but I had an extra 5 quarts of them laying around so I decided to use it.
View 24 RepliesGTI 337/20th Anniversary :: Master Cylinder Is Sticking Somewhere Inside And Causing Pedal To Hang Up
Car: 03 20th with 6spd 02m trans.
Problem: Go out in the morning esp when really cold, and the clutch pedal drops to the floor. No resistance at all on it as if it's no connected to anything. I pull it back up and pedal starts to build pressure.
I thought slave cylinder searching on here shows a high probability of that being the issue. But the strange thing is the pedal feels like it's sticking at the midway point. Once pressure is built up to normal pedal pressure, if I opush it down and slide my foot off it, it will literally rise fast and the feels like it catches on something and pops to the normal top position.
So my thought here is that the Master cylinder is sticking somewhere inside and causing the pedal to hang up. The weird part though is that once the car is warmed up the problem starts to diminish. But if I drive long enough on the highway (not shifting gears) the clutch seems to start losing pressure all over again.
I have also had to top off the brake fluid reservoir about 3 times in 2 months. What is the root cause here?
Ford :: 2001 Mustang V6 Stalling And Misfiring At Red Lights
I have a 2001 Ford Mustang, V6, 3.8 Liters, automatic transmission, 120,000 miles. Recently, my car has started to stall/misfire at when I come to a full stop at a red light. It feels like the car is going to shut down and like it has no power. I have to press the gas really hard to get it to pick up power and speed. It doesn't happen every time and I've noticed that it happens less early in the morning or at night, and it happens more often during the day when it is really hot (I live in Az and temperatures are currently in the 100sF).
The "service engine" light is not turning on. The battery was checked and it's fine (recently replaced in September 2011). The alternator was changed 1 month ago. The cooling fan was replaced 1 month ago. I took it the the Ford agency and no codes are turning up and they can't seem to duplicate the problem even though the ran the car for 15 miles. They checked coils, spark plugs, fuel injectors, fuel filter, gas pump pressure, and it all seems fine. They advised that I fill up my gas tank with Premium gas and add fuel injector cleaning fluid. I did and the problem is still there. They then advised to fill up gas tank again with Premium and add Techrnon additive. I did and the problem is still there.
I am scared that my car will stall and turn off while doing a left turn with oncoming traffic or in the freeway.
Buick - Skylark :: 1991 - Misfiring / Stalling When Press The Gas
I've had a 1991 buick skylark for 3 years, just hit 100,000 miles, and for the past few months i've been having problems with it stalling out/misfiring when I press the gas, almost like a lawnmower running out of gas, and then catch and go fine. it was only happening at the 3rd gear change,(randomly but only at that change), and then it started happening only at the 2nd gear change. it first happened at the end of a long road trip, and the speedometer and odometer stopped working at the same as well, but have since returned. but now it's been happening on cross town trips.
Every time it has happened has been random, and it always corrected itself and was fine. but this last time, it was doing it consistently, at random gear changes and from idle. it finally gave out at a stop sign and it barely stuttered across the intersection, but with the check engine light on and never "catching on" or actually dying/cutting off. I took it to my local shop, and they ran all the computer test and road tested it and told me they couldn't find anything wrong. they tested the fuel pump, which had good pressure. They mentioned it might be the module, but were honest and didn't want to charge me for something they couldn't tell was actually wrong. any clue?
Golf IV R32 :: Misfiring On Cylinder 2 And 5
Happened a few times on me lately. While pulling towards the top of 5th, I'll start to see the check engine light briefly blink as if the car wasn't sure, then at the top of 5th, she'll start misfiring on cyl 2 and 5. It's only during the long haul pulls that this occurs. My plugs and coils were all changed about 1k miles ago.
View 17 RepliesElantra XD (2001-06) :: 2.0L Misfiring / Subsequent Stalling When Stopped At Intersections
My 06 Elantra started to stall / misfire when I was driving it. It doesn't seem to matter how fast I am traveling as it will " misfire" for lack of a better word. It has an automatic transmission, and the rpm's will start to bounce as the car begins to jerk when this occurs.
I don't live anywhere near a dealership, so I brought it to the garage that I take my other vehicles to, and they had a hard time diagnosing the problem due to the fact that there never was an error code coming up or check engine light. They ended up finding a bad coil and changed it out.
That was 2 months ago and I haven't had a problem with it till today when the exact same issues resurfaced. And again no check engine light comes up, just the misfiring and when stopped at intersections, subsequent stalling.
Ford F-150 (2004-2008) :: 5.4 3v - Rough Idle / Stalling And Misfiring
I recently bought a 05 f150 with 5.4 3v and 195k miles needing some work. Ran great, just had a code for timing over retarded. Originally it had a cracked timing cover, so i took it off to replace and found broken guides and bad tensioners on timing. I installed new guides, chains, and tensioners, and cleaned phasers, and put back together only to find it ran terrible and had a phaser rattle. I then went in and installed phaser locks, which took care rattle but not the running issues. I can not figure it out.
ISSUES: My issues almost mirror what is said in this thread here, but this issue was never solved. [URL] ....
My issue is when started cold it starts right up, idles ok, runs ok, although a bit sluggish. Once its warm it stalls at idle, shudders when giving throttle in overdrive, and if you kick it down it will continually backfire, and slowly accelerate... it kicks down but acts like its only getting 1/8 throttle, just kind of hangs at the same rpm and slowly climbs in rpm. Sometimes it wont backfire as much, and sometimes the check engine light flashes. After it stalls at idle and you start it back up it sounds like it shudders/backfires for a split second then starts.
It is throwing many engine codes, but most are from the phaser locks. Throws code for timing over advanced on each bank (phaser locks lock them fully advanced), cam timing codes for each bank, and then a code that doesn't have to do with the timing, P2106. I am going to run some live diagnostics on it today and report back but I am fully at a loss.
LS / MKZ :: 2001 V8 Shuddering And Misfiring On Cylinder 2
Going up a hill this LS started shuddering and misfiring and set the po302 code. A small push on the accelerator sometimes seems to temporarily remedy the issue. This started about a week ago. fuel mileage : 26 mpg highway
Here's the readings I got at idle:
Fuel pressure is KOEO - 0 (That's what it read.); KOER - 30.
MAF - about 70
LT FUEL TRIM 1 - 5.5
ST FUEL TRIM 1 - STAYS NEGATIVE
LT FUEL TRIM 2 - STAYS NEGATIVE
ST FUEL TRIM 2 - STAYS NEGATIVE
ST FUEL TRIM 11 - STAYS NEGATIVE
ST FUEL TRIM 21 - STAYS NEGATIVE
O2 1 - NORMAL FLUCTUATES PROPERLY
O2 S12 - STAYS ABOVE .500
O2 S21 - NORMAL FLUCTUATES PROPERLY
O2 S22 - STAYS ABOVE .500
Not familiar with this vehicle...
Touareg :: Put In All New Plugs / Cylinder 5 Is Misfiring
I have a 2008 Touareg 2, V8, 4.2L.
I bought it used (~95k miles) and almost immediately had an issue. #5 is misfiring. Since then, it has been in the shop 10-12 times with no resolution. Here is what I have done so far:
Put in all new plugs/coils sent the ECU to SIA electronics in Chicago for testing - no errors replaced the injector with a new injector on #5swapped #1 for #5 (plugs/coils)checked the harness (dealership said they did this, but not sure if they did or are just tired of me)
Through all this, #5 is still misfiring. The dealership is out of options, suggesting that the ECU is faulty and needs to be replaced ($1600) or they need to swap the #5 injector with #1 to see if that is the issue (~$1000+). Neither of these options sound reasonable because a) the ECU was already tested and b) the injector is brand new, yet the exact problem (#5 misfire) has persisted before and after the injector replacement.
Passat (B6) :: 2006 2.0T - CEL On And Cylinder 3 Misfiring
My dad has 2006 passat 2.0T. In December 2010 he went overseas. During his absence the car was parked in garage and not in use.
So one day I decided to start the car and as soon as I turned it on the car made this noise and check engine light came on. Took the car to a private repair shop and found out the cylinder #3 was misfiring. The tune up for this car was due so I had all four spark plugs changed and the car ran fine for few days. Then couple of days later it started making the same sound and this time around the coil for cylinder #3 was replaced.
A few days after that check engine light came back and this time it was blinking and the engine was struggling to run, took it again to the workshop yesterday and this time another coil not sure which cylinder was replaced. (all this is done at a private workshop). I have a hunch that the car is going to run fine for a day or so and the problem is going to come back
I never had any major issues with it up until now. Bought this car new in 2006 from dealer. I am afraid that this might be a start of a downhill roll from here on I will drive the car tomorrow and see how it reacts.