Silverado :: 4 Wheel Drive - Humming / Rubbing Noise Coming From The Front End
I have a 2002 Silverado 1500 Z-71. In 4 wheel drive, I can hear a humming/rubbing noise from the front end. Not real loud, but enough to get my attention. It happens at around 25 mph, and just as I'm coming to a stop. This is on the street.....going straight, not while turning. I only engage the 4 HI during street driving on a straight line drive just to "exercise" the gears and transfer case. I don't notice it on the dirt 'cause of trial noise levels. All fluid levels are normal in transfer case and axles. How much noise is normal during 4 wheel drive operations?
View 14 RepliesFord F-150 (2009-2014) :: Rubbing Noise And Vibration Coming From Right Front Wheel
I have noticed recently that I have a "rubbing" noise and vibration coming from the right front wheel on my FX4. It is most noticeable from 5-10 MPH, and more pronounced when turning right. it is not constant. It sounds almost like a brake pad rubbing on a badly warped, wet rotor. It goes away when I apply the brakes. I am thinking bearing or possible CV joint.
The dealer can't get it in until Tuesday, and they say I will have to pay the deductible on the ESP, even if it is related to the steering vibration they could not replicate or fix about a month ago. I am seriously considering going to another dealer for my service. Given, they did absorb the deductible last time, but they didn't fix the problem!
Yaris/Scion & Vitz :: Drivers Side Front Wheel Rubbing Type Noise On Echo
I'm getting a rubbing type of noise when i'm turn right and it sounds like a rubbing noise perhaps its a wheel bearing? how easy/hard is that to change. The noise is most notable when I'm on the highway and I'm making a left lane change or if I'm coming or going on a off ramp (left).
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Light Metal Rubbing Noise Coming From Front Left Wheel
I have developed a sounds that sounds like metal on metal. Not a grinding but more of a "swish swish swish" light metal rubbing when the truck has been running a mile or two. I can barely hear it over the radio but its very noticeable when the window is down. It is not affected by the pressing the brakes and it gets louder and faster in direct portion to speed. It will occasionally leave and start right back up. I touched the front rim around the hub and it was hotter than I wanted to hold onto. It didn't burn but it was hot. It was 105 degrees that day. Here is what I have done.
I replaced that front hub in 2010 and probably have 50K miles on it. I did the 3-9 test and there was no noticeable play. I spun the hub and while it seems to spin ok it does seem a little dry.... I will pull it tomorrow and see what it looks like.
I pulled the calipers off and the brakes pads are at half way and there is no burnt smell. I spun the rotor and it seemed flat and straight. I do have a small tiny lip all the way around them on both sides but I figured that's normal with 265K. I pulled the pins and they were dry but they didn't seem to be sticking. I cleaned them up with the boots and am going to replace them when I get some brake grease tomorrow. I have not looked real hard at the caliper but I plan on pressing that with a C-Clamp tomorrow to check it. Since the rotors and pads looked OK, I assumed there was not a stuck caliper although haven't ruled it out. The axle behind the hub seem to spin freely before I removed all this stuff and the hubs are not locked.
I think I covered it all .. I also thought it could be a rock or stick but nothing came out of my caliper or rotor when I took them off ..
Sierra :: 1984 K2500 4WD - Front Wheel Bearings Loose
1984 K2500 4WD 8-lug
Front DS wheel hub. The front wheel bearing nuts come loose all the time. I have to check it every weekend, usually starts to get loose after a week and I have to pull apart the hub and re-tighten the nuts. Bearings are all okay, but tires wobble when they get loose...
Reverse order of install: nut -> keyed washer -> nut -> washer -> snap ring -> 4wd auto engaging assembly -> spring seat -> cap seal -> spring -> cap
My understanding is the deepest nut gets adjusted so that the bearing is tight enough that nothing wobbles but not so tight the wheel can't freely spin. Then the keyed spacer goes in and the second nut is tightened down hard to lock the first nut in position.
I've had on-and-off issues with the front DS in general as well. That side the brake caliper always start to suck in air after a few months, on #4 now. Brake system has been replaced with rebuilt MC & calipers, all new lines and warning switch. Also the 4WD doesn't seem to lock in on that hub every time. It will engage, but doesn't hold if it gets too much torque. Then other times it engages and locks and won't have any problems until next time I want to use it. It works about 70% of the time. I've taken it apart and checked everything, no burrs or wear that I've noticed to cause it.
GTI 337/20th Anniversary :: 2004 - Noise From Front Passenger Wheel
I got 66,000 miles and I am getting a rattle/popping noise when driving on roads that are bumpy. I thought it might be a strut going bad but somebody told me it might be a Lower control arm rear bushing....
View 2 RepliesPassat (B6) :: Loud Clicking Noise Around The Front Passenger Wheel
I'm getting a loud clicking noise on my front passenger side around the wheel or axle. Once I press on the accelerator it starts. It goes faster and faster as the speed of the car increases.
View 5 RepliesPassat (B5) :: Noise From Front Passenger Side Wheel On Wet Roads
Every time I drive on a wet road I can hear my front passenger side wheel going though the water and the driver side makes no noise. What, if any, could be the problem?
View 4 RepliesGTI 337/20th Anniversary :: Rubbing On Front Passenger Side?
Couple of days ago I notice some rubbing on my front passenger side and I'm pretty sure it's my sway that rubs on the axle. I could understand that if I was slammed but I'm not even all the way down on my vmaxxs. I have about 15 threads left and it still rubs especially while making left turns. When I first got my coilovers I used to drive all the way down with no issues but now it's getting worse and worse and I don't know what to do besides going up couple of threads. The tricky part is that my driver's side front doesn't rub at all. Any ides why would start rubbing all of the sudden when it never rubbed before even when I was lower? Is there anything I could do, maybe adjust the end links or something? I know I can cut the sway out but but I'm pretty sure there is another way to fix it since it started rubbing recently.
View 13 RepliesBMW :: 2002 - Squeaky Noise Coming From Passenger Side Front Wheel
I have 2002 BMW 325xi (all wheel drive). For about 2-3 months now there is a squeaky noise coming from passenger side front wheel. It sounds like a really bad and rusty coil spring but the weird part is that that noise only appears in warm weather. It has nothing to do with how much distance I drive. If it is 70 odd degrees or warmer outside, the noise starts. In warm weather, the car does not have to be running/moving to hear the noise. I can just push down the passenger side front and hear the noise. I took to a mechanic and he wants me to replace tie rods, control arm and struts. basically the whole suspension system on the front for this noise (in other words, he does not know what exactly is making the noise, so replace everything)
View 5 RepliesSubaru - Imprezawrxsti :: Clicking Noise From Passenger Front Wheel Area
I have an 04 WRX, I've upgraded the suspension (1.5" - 1.75" drop front and back respectfully) and have a full set up of strut tower braces. Recently when accelerating from a stop, I get a clicking noise from the passenger front wheel area, I hear it all the way through first, second, and most of third...the sound is probably present after that but my exhaust drowns it out. My first choice of problem is that the CVs have gone, the car has 140k on it...
View 2 RepliesFord - Explorer :: 1996 - Wheel Shake - Noise From Passenger Front
I have a 96 explorer 4x4 that i just bought and it has wheel shake. It also has a slight noise coming from pass front. So i jack it up and there is zero wheel play. I spin the wheel and it spins kinda freely until about 3/4 away around then it has some resistance to stop the wheel. Im thinking that could maybe a rotor a lil warped but not sure. Same wheel there are wires showing on the inside. Now i try the driver side and i cannot spin that wheel it has resistance all the time. So could this be hub or maybe just bad tire?
View 12 RepliesFord F-150 (2009-2014) :: Grinding Noise In Front Passenger Wheel
Just installed new actuator and wheel hub assembly on my 2009 f150,truck still had grinding noise in front passenger wheel , New solenoid and vacuum hose kit installed when test drove noise still there until you put the truck in 4 wheel drive it disappears . The noise returns as soon as you take it out of 4 wheel drive. Also mechanic said steering was tight,installed new shaft same thing, could this be the rack and pinion.
View 5 RepliesGolf IV R32 :: Passenger Side Front Tire Is Rubbing On Inside Well
Just put on new wheels 19x8.5 all around on 235/35/19s. Figured to have no issues, not super low or anything. Passenger side front tire is rubbing on the inside well pretty good. Not on fenders as far as I can tell, just the actual inside of the wheel well. Fender liner is already out on that side as well. Not a thing on drivers side though, and the liner is still in. Thinking maybe just need an alignment.
View 4 RepliesToyota - 4runner :: 1996 - Noise Coming From The Front Passenger Side Wheel
It seems to be coming from the front passenger side wheel well area. It's only present during braking and coming to a stop. Seems to be also related to wheel speed. The brake performance doesn't seem to be impacted but it's very embarrassing creaking through a parking lot. The noise doesn't seem to be present on a cold start but once the brakes warm up it really comes to life.
I noticed with both wheels up off the ground that the front passenger side wheel (The side making noise) had more resistance than the drivers side when trying to spin. [URL]...............................
Toyota - Corolla :: 2006 - Squeaky Noise From Passenger Side Front Wheel
I drive a 2006 Toyota Corolla, and I've noticed e a squeaky noise coming from my passenger side front wheel. The noise only occurs when I am accelerating the car and driving between 20-40 mph. As I accelerate, the squeaks increase in frequency. They disappear when I brake.
A mechanic replaced the front brake pads two years ago (15,000 miles ago) and also shaved the rotors. About a year later, the squeaks began. I brought the car into a different mechanic at that time (because I moved) and asked them to take a look. They checked the brakes and said they looked good. They attributed the noise to metallic brakes as opposed to ceramic and said the noise would go away in time. The noise has persisted, however, and is becoming more intense.
What is going wrong? Could this be a CV joint or wheel bearing issue? A rotor issue?
Elantra MD (2010-15) :: Loud Grating Noise From The Passenger Front Wheel Area
I have a 2011 E Sedan and recently started hearing a loud grating noise from the passenger front wheel area. It only happens when turning the wheel to the left. It isn't a popping noise like the traditional CV Joint and the boot is still intact.
I jacked the front up today and put it on jack stands. I pulled the tire, caliper, caliper mounting bracket, and rotor to look at the dust shield and there was no sign of it rubbing, nor was there any other wear marks. With everything still disassembled, I turned the wheel hub with my hands and noticed the same, though fainter, sound. I started the car and put it in drive and once again the same noise was coming from the hub assembly area, although I didn't use a stethoscope to listen.
The noise is more profound when under load turning left, but it still seems to coming from the same area. My plan is to replace the entire wheel hub assembly since they aren't that expensive. That, and I don't want to go through the headache of puling everything apart to simply replace the bearings.
Honda - Accord :: Strange Noise Coming From Front Passenger Side Wheel
So I drive a 98 Honda, 118k miles, and for last month I've got a really strange noise coming from my front passenger side wheel. It happens when I apply the brakes, usually at a slow speed, slowing down from something like 30mph to a stop. When slowing down, if I have just a bit of pressure on the brake, the noise seems to go along with the speed of the wheels. It also happens when I accelerate from a stop.
I can only describe it as a kind of creaking noise, almost like it is coming from the spring. Sometimes it sounds a little tinny, sometimes not so much. I don't think its actually in the suspension, because it doesn't make noise if I go over speed bumps or press down on the fender. Brake pads have a good amount of pad left on them.
My hunch is that it might have something to do with the fact that I hardly ever drive anymore, somewhere around 10-20 miles a week, back and forth to the subway essentially (fair amount of time driving down banked turns in a parking garage if that adds any info). My dad knows a decent amount about cars, but he isn't sure what is going on, though he thinks it nothing dangerous. Strange wheel noises always make me wary though.
Cavalier :: Repetitive Rubbing Sound At Front Wheel
I have this repetitive rubbing sound coming from the driver's side front wheel. It increases as I go faster and slower as the car goes slower. When I apply the brakes the sound disappears. It usually isn't audible when first driving but will show up after a few minutes. If I'm turning slightly to the left it will go away, or if I make a right turn I will occasionally get a rattling noise that's distinctly different.
I had this looked at a while ago, before the rattling noise appeared, and they determined it was a motor mount and replaced that. The noise did not go away.
I've taken a look at it and do not see anything obvious. Brake pads are still good, rotor is smooth and not visibly warped (though it has more rust on it than I'd like). I tried moving the tire to see if the bearings were shot but didn't have any luck (I'm not ruling it out yet).