Ford Excursion :: 2001 - Tranny Fuse Blowing - Electrical Malfunction - Wiring Diagram?
I posted earlier about the tranny in my 01 Ex v10 having a transmission problem. The show looked at it and found the O2 sensor had shorted out and in some way sending the truck in to limp home causing the tranny fuse to blow????
Any way they fixed it or so they said and I drove it for a few hours and it did fine. The next morning I drove it and it blew the fuse. (under hood box I belive #19) I took it back to the shop and they beat and banged on it....got it wet etc. and can not get it to do it again. I know whe have an electrical issue but what all runs off of the fuse that controlls the tranny?
Is there any online wiring diagrams of excursions or superduty drive trains? Where all to look for the problem?
Ford Wiring/Electrical :: 2001 - Turn Signals Stop Working When Vehicle Heats Up
I have a 2001 Econoline and the turn signals work in the morning but when the vehicle warms up they stop working. I have replaced the bulbs and the fuses. What I could try next.
View 4 RepliesElectrical-wiring - Brakes - Suzuki - Grandvitara :: 2001 - Brake Light Fuse Keeps Blowing
I'm having brake light issues with a 2001 Suzuki Grand Vitara. The brake light fuse keeps blowing. The last time driven with me following the driver side brake light was dimmer than the passenger side. At one stop the driver side brake light pulsed brighter for a split second then went back to dim. A few stops later it became as bright as the passenger side and stayed that way for the rest of the trip. The driver put in a breaker fuse and it was in during the observed trip. I'm not sure of the brake light visual symptoms without the breaker fuse in other than that the fuse keeps blowing which prevents the vehicle from being shifted out of park. What the problem could be? Bad ground?
View 4 RepliesFord F-150 (2004-2008) :: Turn Signals And Hazard Lights Quit Working / Blown Fuse Now Truck Won't Start
My 2007 F150's turn signals and hazard lights quit working. I checked the fuse and it was blown. Once I pulled the old fuse out the truck wouldn't start at all. What happened?
View 3 RepliesFord Wiring/Electrical :: Overdrive Fuse Keeps Blowing
Overdrive fuse keeps blowing. Drive one and 2 shifts fine. 3 and overdrive don't work. Had transmission checked it is fine. Repair shop says it is electrical.
View 1 RepliesFord Wiring/Electrical :: Fuel Pump Keeps Blowing A Fuse
I have a 1994 Ford Ranger king cab 4x4 with a three inch lift kit on it . My problem is the fuse is blowing that goes to the fuel pump . It started out blowing the fuse now and then when it was raining . Well I thought it mite be the fuel pump going bad but after I put the new pump in the truck it lasted about a week and started blowing fuses again . I put another fuse in and it go a few days and blow it . Last week on a 100 mile tripe I got almost there and it burned a fuse on the highway . I tried to put another fuse in and it would blow it as soon as I tried to start the truck . Burned five fuses right then . So I had it towed to mothers house and put another fuse in and it cranked up . I looked at the wiring that was not wrapped in that plastic cover stuff and have not found anything yet ...
View 14 RepliesFord Wiring/Electrical :: Running Light Fuse 17 Keeps Blowing
2006 F-250 SD... I Keep popping the 15A #17 fuse under certain conditions - Driving forward
1. Start with good fuse.
2. Start engine, while in park, turn on parking light...4.8A on circuit. No problems.
3. Put into reverse and drive. down the block around the corner and back up to the house... No problem. 4.8A on circuit.
Put the shifter into drive and - POP - the fuse goes. I never see a jump in the current. 1-5 seconds until fuse goes. While conducting testing, I have had the fuse blow when shifting from reverse to park. Looking at the wiring diagrams, I don't see a common wire that would cause a short when shifting. What I should try next?
Ford Wiring/Electrical :: 2005 - AC Clutch 4x4 Solenoid Fuse Blowing
My 2005 4.6L 4x4 screw is blowing the 10amp a/c clutch, 4x4 solenoid fuse whenever i turn the a/c on, at times whenever I turn the defrost on. the fuse does not blow when i turn the key to power (no engine start) but when engine is running fuse will trip. I disconnected elect. Connection at compressor and fuse still blows, also seems like no power or life from compressor.
View 3 RepliesFord Wiring/Electrical :: 2006 F350 - No Power To Fuse Box
I have a 2006 F350 Diesel. Had one of my employees go out to start the truck yesterday and when I went out I had no electrical power to most of the accessories (gauges, warning lights, power windows, radio, interior lights, turbo charger). It also seems to have no power - could barely make it go up the slight incline into my garage. I have checked all the fuses - they seem fine. Although put a tester on the interior fuse box and I don't have any power to the fuses that run these accessories.
View 10 RepliesFord Wiring/Electrical :: Speedometer And Cruise Control Not Working / Fuse 18 Keeps Blowing
I have a 1994 f150 5.0 engine and automatic transmission. Problem I am having is speedometer, cruise control is not working. Overdrive light is flashing and number 18 fuse keep blowing. horn is still working...
View 1 RepliesFord Wiring/Electrical :: 1994 Explorer - EEC Fuse Blowing / Relay Melted
I purchased a 94 Ford Explorer 4x4 4.0L w/ Automatic transmission with Overdrive. Great work truck, but I am finding that these had a lot of wiring problems. First thing that messed up with me is the backup lights wouldn't work. Then the dash lights and parking lights stopped working (Still no fuses where bad). Then about 2 weeks later, I was on my way home when It just died like someone had turned the switch off, I pulled off the side of the Interstate, and after checking my fuses/Relays under the hood.
I found that the EEC Fuse (30AMP-BIG Fuse) had blowed, I didn't have one and the truck wasn't off the road good, So I wrapped a small wire around the fuse to see if I could start it and get it out of the road better, It started right up, but soon as I pulled it off the road it died again, and I found that it melted the EEC Relay, I went to the parts store and got a new relay and fuse and put them in, It blows the fuse as soon as I put it in, with the switch off or on. I just need to know what things will cause this so I can check them out one by one, until I find the one that is causing this problem, cause It run great up till this happen.
Only other thing I may need to let you know, Is when I bought it, the key switch would start it, The guy had put a push button starter switch that you push to start it with the key on, I unhooked it, and it started fine with the key for a while then it stopped again, so I had to hook the push button back up and had been using it until it stop running with me.
Ford Wiring/Electrical :: Turn Signals Will Not Work With Engine Running
My turn signals will not work with the engine running. With the engine off they will. With the engine running if I move the ignition like I am going to turn it off they work.. Is it the ignition switch or ign cylinder....
View 5 RepliesFord Wiring/Electrical :: 2006 E350 - Flasher For Turn Signals
I must be missing something here. Where is the flasher for the turn signals? It isn't the two relays behind the radio is it?
View 2 RepliesFord Wiring/Electrical :: 2006 F150 - Turn Signals Won't Work
I have a 2006 f150. Both front turn signals do not work. I replaced bulbs still nothing. There back signals do work. They blink really fast.
View 4 RepliesFord Wiring/Electrical :: Passenger Side Does Not Light For Brakes Or Turn Signals Suddenly
I installed LED tail lights a few months ago, now all of a sudden the passenger side does not light for brakes or turn signals. The lights came with resistors that I put in when installing and the adhesive wore out and they were dangling in the truck frame. The wires connecting the resistors to the light were damaged. I taped the exposed wires and secured them a with a heavier tape, but taping did not work. I also tried switching the resistor packs with the driver side to see if it was them that have an open winding, but they are still operable.
I narrowed it down to wiring between the trailer hook up and passenger light assembly in the electrical circuit. I plugged an LED light bar into the trailer connection and the same problem occurred (running lights come on, but no turn signal or brake light). Where could there be a short? Or is this circuit fused somewhere that the running lights come on but a separate fused circuit triggers the higher voltage for LEDs.
Ford Wiring/Electrical :: 2004 F250 - Turn Signals And Hazards Stopped Working
So I have an 04 F250 Super Duty 6.0L and suddenly the turn signals and hazards stopped working. First I replaced the switch on the steering column...no luck. Today I replaced the flasher relay under the dash panel (the blue one)...still no luck. I remember checking fuses in the fuse box but don't remember which ones I checked but I didn't see anything obvious. I also took a quick look under the dash at all the wires for any anomalies...nothing. I'm lost... What to do next!?
View 1 RepliesFord Wiring/Electrical :: 2004 F150 - Brake Lights / Turn Signals And Flashers Not Working
My brake lights, turn signals, and flasher are not working in my truck. Is it a fuse and what fuse? Could it be a relay?
View 2 RepliesFord Wiring/Electrical :: 1973 F250 - No Turn Signals / Brake Lights Or Rear Hazards
Dad borrowed truck and wired 7 pin trailer harness. Lights worked on truck/trailer for use but upon return the turn signals didnt work. Hazards and running and brake lights did work. Replaced TS flasher and Haz flasher. Still no signals. Pulled steering wheel and replaced turn signal cam only, not whole switch. Now no brake lights, no rear hazards or turn signals. Losing my marbles trying to follow schematic and using test light and mulit meter. All bulbs and fuses are good. Running lights and head lights working as well.
View 6 RepliesFord Wiring/Electrical :: F350 Truck Would Act Like It Ran Out Of Gas Then Pick Up And Go Again
Truck is up in the back country and has quit. It has two factory gas tanks, I can't hear either of the fuel pumps will come on when you turn the switch on. The problem started as an intermittent fuel starvation issue. Truck would act like it ran out of gas then pick up and go again. Switched tanks back and forth but it got worse throughout the day and finally will not start at all. I have listened to both tanks when the ignition switch is turned on but can not hear the pump come on for either tank (switching the selected tank with the switch on the dash). We went through some bumpy terrain just before the problem started so I am thinking maybe a wire might have come loose or got broke somehow. I am asking for wiring schematic so I can check for voltage in the correct place going to the fuel pumps. Both tanks are full of gas so for now dropping either tank is not an option.
View 8 Replies