Ford Wiring/Electrical :: 1994 F350 - Location Of Turn Signal Relay?
Long story short, my truck's front turn signals and rear turn signals/tail lights won't work. I am thinking that the relay is burnt. Whenever I look in the manual I can't seem to find the location for this relay. Is is built into the flasher?
Also, I am just assuming because the rear turn signals and tail lights are the same bulb that fixing this should clear up both problems. Am I right in thinking that?
I have already checked all of the fuses. Also, the Hazards don't work either.
Ford Wiring/Electrical :: Overdrive Fuse Keeps Blowing
Overdrive fuse keeps blowing. Drive one and 2 shifts fine. 3 and overdrive don't work. Had transmission checked it is fine. Repair shop says it is electrical.
View 1 RepliesFord Wiring/Electrical :: Fuel Pump Keeps Blowing A Fuse
I have a 1994 Ford Ranger king cab 4x4 with a three inch lift kit on it . My problem is the fuse is blowing that goes to the fuel pump . It started out blowing the fuse now and then when it was raining . Well I thought it mite be the fuel pump going bad but after I put the new pump in the truck it lasted about a week and started blowing fuses again . I put another fuse in and it go a few days and blow it . Last week on a 100 mile tripe I got almost there and it burned a fuse on the highway . I tried to put another fuse in and it would blow it as soon as I tried to start the truck . Burned five fuses right then . So I had it towed to mothers house and put another fuse in and it cranked up . I looked at the wiring that was not wrapped in that plastic cover stuff and have not found anything yet ...
View 14 RepliesFord Wiring/Electrical :: Running Light Fuse 17 Keeps Blowing
2006 F-250 SD... I Keep popping the 15A #17 fuse under certain conditions - Driving forward
1. Start with good fuse.
2. Start engine, while in park, turn on parking light...4.8A on circuit. No problems.
3. Put into reverse and drive. down the block around the corner and back up to the house... No problem. 4.8A on circuit.
Put the shifter into drive and - POP - the fuse goes. I never see a jump in the current. 1-5 seconds until fuse goes. While conducting testing, I have had the fuse blow when shifting from reverse to park. Looking at the wiring diagrams, I don't see a common wire that would cause a short when shifting. What I should try next?
Ford Wiring/Electrical :: 2005 - AC Clutch 4x4 Solenoid Fuse Blowing
My 2005 4.6L 4x4 screw is blowing the 10amp a/c clutch, 4x4 solenoid fuse whenever i turn the a/c on, at times whenever I turn the defrost on. the fuse does not blow when i turn the key to power (no engine start) but when engine is running fuse will trip. I disconnected elect. Connection at compressor and fuse still blows, also seems like no power or life from compressor.
View 3 RepliesFord Wiring/Electrical :: Speedometer And Cruise Control Not Working / Fuse 18 Keeps Blowing
I have a 1994 f150 5.0 engine and automatic transmission. Problem I am having is speedometer, cruise control is not working. Overdrive light is flashing and number 18 fuse keep blowing. horn is still working...
View 1 RepliesFord Excursion :: 2001 - Tranny Fuse Blowing - Electrical Malfunction - Wiring Diagram?
I posted earlier about the tranny in my 01 Ex v10 having a transmission problem. The show looked at it and found the O2 sensor had shorted out and in some way sending the truck in to limp home causing the tranny fuse to blow????
Any way they fixed it or so they said and I drove it for a few hours and it did fine. The next morning I drove it and it blew the fuse. (under hood box I belive #19) I took it back to the shop and they beat and banged on it....got it wet etc. and can not get it to do it again. I know whe have an electrical issue but what all runs off of the fuse that controlls the tranny?
Is there any online wiring diagrams of excursions or superduty drive trains? Where all to look for the problem?
Ford Wiring/Electrical :: 1994 Explorer XLT - Occasional Click When Trying To Start
I have a 1994 Ford Explorer XLT. It just died the other night. I have dim dome light, nothing else. I had the battery and alternator tested, both are ok. I get an occasional click when trying to start it. I also get an occasional beeping, the key in the ignition sound. I've checked the fuses, and can't find a broken one.
View 3 RepliesFord Wiring/Electrical :: 2001 F350 - No Turn Signals When Start The Truck - Fuse 1 Keeps Blowing
2001 F-350 diesel. Out of nowhere, I start the truck and there's no turn signals. Fuse is blown so I replace it. It immediately blows. Tail lights work. No turn signal, brake lights, or hazards. I haven't hooked up a trailer or done anything abnormal recently. Only the #1 fuse (20Amp) is blown. Pulled bulbs and they work fine. Inspected wiring under and near lights. NOTHING! Any way to localize a short?
View 2 RepliesElectrical-wiring - Brakes - Suzuki - Grandvitara :: 2001 - Brake Light Fuse Keeps Blowing
I'm having brake light issues with a 2001 Suzuki Grand Vitara. The brake light fuse keeps blowing. The last time driven with me following the driver side brake light was dimmer than the passenger side. At one stop the driver side brake light pulsed brighter for a split second then went back to dim. A few stops later it became as bright as the passenger side and stayed that way for the rest of the trip. The driver put in a breaker fuse and it was in during the observed trip. I'm not sure of the brake light visual symptoms without the breaker fuse in other than that the fuse keeps blowing which prevents the vehicle from being shifted out of park. What the problem could be? Bad ground?
View 4 RepliesFord Wiring/Electrical :: 1977 - No Start - Ignition Wire Melted?
My 77 F150 Ranger with a 400 in it didn't wanna start up at all. It wouldn't even crank or click like if the battery was dead. Then I tried again this morning and it cranked once then melted a red wired with I think a black or gray tracer, on the ignition. (I put a new solenoid on a couple months back and the positive also melted a bit by the solenoid but didn't pay any attention to it.) I'm just wondering what could be wrong with it to make it do that and how to fix it. Also when I went to put gas in it (it's on a slight hill making it lean to the driver side) it was empty but no fuel would go down the filler neck, then it started to gurgle and spit it out some. I was told it was vapor lock but I thought vapor lock happens when it's hot.
View 3 RepliesFord Wiring/Electrical :: 1990 F250 Hard To Start - Glow Plug Controller Relay Wiring
I just bought a hard to start 1990 F250. Per the board, just replaced all 8 glow plugs with Motorcraft. Still wouldn't start (it turns over but will only start if you use either). I attempted to install a new BWD brand (Borg Warner I believe) glow plug connector relay today...I removed the old no problem, but am unsure what wires to plug where....the only connection that I'm sure about is the blue wire that works the WTS feature...it plugs in easily but I don't know if there are other connections that need to be made or not? All the wires run from the posts and into the bottom of the unit.
View 2 RepliesLS / MKZ :: 2004 Blowing Heat All The Time - DCCV Wiring Harness Melted
My car was blowing heat all the time and after reading some of the intel on this site and running a few checks I decided it was the DCCV. I bought a new one and while changing it i noticed that the old DCCV was burnt up and so was the wiring harness plug. I went ahead and installed the new one hoping the harness would still work. Well it worked great for about a half hour then the ac compressor stopped coming on! I checked the freon and it is good. I believe it is the harness (and yes I checked the fuse). On the harness was a tag with the numbers 3W4T-18C463-BC ...
View 14 RepliesFord Ranger / B-Series :: 1992 - EEC Relay 30 Amp Fuse Keeps Blowing?
I recently got a ranger from my buddy and it keeps blowing the EEC fuse in the engine compartment. We have replaced the EEC relay and the EEC power relay. As soon as you turn the key it is blowing the fuse.
View 1 RepliesFord Wiring/Electrical :: 2004 F350 - Auxiliary Relay Work Intermittently
I am having issues with my auxiliary relay on my truck. It will work intermittently. It started with me just needing to give the relay a light tap for it to work, and is now progressed to needing me to push really hard on the relay for it to turn on, but then as soon as I let go it shuts off again. I have replaced the relay with a new one and it's doing the same thing, and have even tried some di-electric silicone on the terminals with no success.
I was thinking of pulling out the entire fuse/relay panel and see if the contacts have pushed out, but then I read a thread regarding the panels and issues involving the removal the terminals and breaking the panel. 2004 F350 CCSB 6.0L...
Ford Wiring/Electrical :: Interior Lights Coming On Dimly And Relay Buzzing
I have a 2000 F350 7.3. I started out with my batteries dying after a few days of sitting. I found the interior lights were coming on dimly, and the relay buzzing. great, got it. I pulled the fuse and ordered the dimmer/light switch. I came back next week and the batteries are dead again. Charged them, drove the truck, and then the radio starts coming on without the key on. Pulled the radio.
Next day the truck starts fine, but now the seatbelt noid is going off all the time and the tranny overdrive is blinking "off" but still shifts fine, and goes into overdrive. The speedometer also works erratically... I read a post about the marker lights leaking, I looked and that's a definite possibility. My question is are all these related back to the GEM or BCM? or more problems?
Ford Wiring/Electrical :: 1996 - Wire A/C Switches To Shut Off Compressor Relay
I'm planning the install of a 1996 351w into my '77 F-100. I'm using the '96 accessory serpentine drive (FS-10 A/C compressor, '96 alternator, etc.). It needs to mate up to the '77 wiring. I'm going to use stock '96 underhood A/C components (accumulator, hoses, condenser).
As best as I can tell, the '96 system uses the ECU to manage the A/C system, but I've converted the '96 motor to a carb.
Looking at both the '77 and '96 systems I think the easiest underhood wiring solution would be to use the '77 compressor ON wire as a relay trigger, and use the '96 High Pressure Cut Off (HCPO) on the compressor manifold, and compressor cycling switch attached to the accumulator to interrupt the relay output to the compressor.
I can get the switches and pigtails, and I can look up their pressure trigger points, but I don't know the voltage the '96 switches operate at (12v or some reduced voltage?) or how to simulate their trigger conditions to see how they work. I guess that at ambient pressure the HPCO should be normally on and the cycling switch should be normally off. So I could just wire them into the relay ground or trigger connection. But of course they aren't simple two wire switches. (Edit: Looking at it online, the cycling switch appears to be two wire, the HCPO is 4 wire).
How to wire them, should I use them to interrupt the relay ground or trigger connection?
Ford Wiring/Electrical :: Transfer Case Shift Relay Module Location
Where it is located in a 97 F150 XLT Automatic with the ESOF?
Transfer Case Shift Relay Module
If it goes bad, would it be possible to still select 4L just no 4H?
Ford Wiring/Electrical :: 2000 - Clicking Coming From #2 Relay Switch Under The Dash
In an attempt to bleed my drivers side caliper today I noticed clicking coming from the #2 relay switch under the dash. The clicking stopped once I pulled out the relay. I continued to bleed my caliper which I've been having issues doing so. It was kinda odd how I was able to bleed the caliper after pulling the relay. Is it possible that the [email protected] system could be causing issues with the pcm? 2000 f 150 4.2 v6 232,000 miles .....
View 9 Replies