Ford - F150 :: Transmission Stuck In 4th Gear - How To Get Back Into Neutral
My manual transmission got stuck in 4th because of a melted oil trough sticking between the gears. I got all the plastic out, and the dog clutches/collars are "free." But, I don't know how to put the gears back into neutral. When it's reassembled, the stick doesn't work to change the gears. How can I get the gearbox back into neutral?
View 19 RepliesTrailBlazer :: Car Acts Like It Goes To Neutral In Third Gear
My daughter just gave me her 2003 TB, about 180,000 miles. She never serviced the tranny but changed the motor oil religiously. She went to take it out one day and it wouldn't shift out of 1st. There was no warning, such as, sluggish shifting, hard shifting, slipping.
I dropped the pan, (no metal shavings just some grey slimy gunk) changed the 2 shift solenoids, filter and fluid. Now the TB has first and second but acts like it goes to neutral in third (no third). Before I give up on this tranny I was wondering if there is anything else I should look at: vacuum leak, known electrical issues with the tranny, PCM. It does not set any codes.
Honda - Accord - Transmissions :: While Depressing Clutch Neutral Acts Like 4th / 5th Gear?
My car stalled one day like I was in a high gear at too low of a speed when i was in neutral. It now acts as if it is in a high gear all the time when I am in neutral. When I press the clutch it will idle like it is supposed to but when i let off it pushes forward slightly then stalls exactly like it would if i was in 4th or 5th gear. When I shift into 1st 2nd 3rd or reverse it dies as if it is in gear but will not move even slightly, when I shift into 4th or 5th it again dies but it but is acting just as I would expect 4th or 5t to at a complete stop i feel slightly more power in 4th which is expected being a lower gear but I also feel 5th pull just like its supposed to. I cannot get it to come out of the high gear it is in even though i can move the stick into the neutral position. It is difficult to get the shifter into 4th or 5th but it will move into the other positions like it should with the same no power result. My clutch is fairly new and i have tried inspecting my sift linkage wit no obvious problems. (1991 honda accord lx 5 spd, 2.2 sohc)
View 2 RepliesFord Super Duty (1999-2016) :: 2006 F550 - Transmission Acts Like Shifted Into Neutral / RPMs Flare Up
06 F550 w/5r110w. Truck and trans runs great then trans acts like it was shifted into neutral, rpm's flare up and if you don't get your foot out of it the trans will re engage aggressively. Changed the speed sensor on the rear axle, there are no codes, had a trans shop change the filters and fluids then change out all of the solenoids. They tell me its not a trans problem.
View 3 RepliesFord Transmission :: 2000 F150 - Transmission Holding 2nd Gear Too Long Before Shifting Into 3rd
I have a 2000 F150 5.4L with 157k miles on it. I think it has the 4r70w trans. The transmission has started holding 2nd gear too long before shifting into third. Throttle position doesn't matter, it does it even under light throttle. I do not have a check engine light. I have owned the truck since new and the trans fluid has been changed 3 or 4 times. The fluid looks pretty good now, not burnt or anything. The truck has been sitting in the garage a lot over the past 2 years, I drive it at least once a month and have put maybe 2000 miles on it this year. It shifts fine through the other gears, just 2-3 has an issue. Truck has the towing package.
View 6 RepliesFord - F150 :: 1998 - 3rd Gear Gone In Automatic Transmission
1998 Ford f150 172984 miles automatic with 4x4 runs and drives transmission is going out will not hit 3rd gear have to drive in 2nd. Is there a fix without pulling the transmission?
View 5 RepliesFord Transmission :: 1994 F150 Not Shifting Into 3rd Gear Or Above
My 94 F150 has been actingup lately with the 4r70 transmission not shifting into 3rd gear or above. I replaced the MLPS sensor and re pinned the plug as per the instructions with the switch.The old sensor had the plug on the side, same type of plug, but wires indifferent spots. Truck wouldn't start like that, so repinned to match the instructions. I couldn't get the neutral mark to 100% line up as there is not enough adjustment, but it is very close.
The old plug had
32-298-140-33
57-199-359-463
I switched it to
57-359-199-463
33-140-298-32
Then tried
463-359-199-57
33-140-298-32
Truck still won't shift to 3rd, overdrive off button doesn't light up and itwon't start in neutral. I tested the ground at the connector and it lights up atest light connected to the pos bat cable with no issues.
Back up lights won't work, but flicker as going from R to N, so I suspect that is due to the fact I couldn't get the marks to line up 100%, but i'm not worried about that now.
Ford 7.3L Power Stroke (1999-2003) :: Trans Not Shifting Into 1st Or 2nd / Truck Acts Like In Neutral
So I put in new clutch yesterday. Reverse works, granny works, 3,4,5 work. ZF6 manual. But when I try to go 1st or 2nd. Its as if the truck is in neutral....what should I be looking for. I bought the truck having only knowing the clutch was completely shot, was not told about this 1&2 gear issue....
Do I need to pull the trans out again... or is there something I can see or adjust, because from what i can see where the shifter connects there is no adjustments. Is it probably a gear selector fork...or connection that took a crap. when moving in granny gear i did not hear any irregular noises....
Ford Transmission :: 1982 F150 - Slow To Shift Into Any Gear
My 82 f150 4x4 302 c6 trans is acting up. My c6 is slow to shift into any gear when I shift the column shifter, after a moment it jerks into gear, also it doesn't seem D is doing anything but all the other gears seems to function manually or auto.
Fluid level looks ok, maybe a little high on the dipstick. I'm going to check the modulator and do a fluid/filter change but looking for a link to the band adjustment screw ?
Dodge - Neon :: Car Acts Like In Neutral
My car was acting like it was in neutral. After cooling down for 20 minutes, it would drive about a block. Then it would not drive.
View 12 RepliesFord Transmission :: 2003 F150 - Difficult To Put In First Gear / Little Grind Or Thump?
I just got my 03 F-150 with 112k on the clock. It has the manual 5 speed tranny behind the 4.6L.
However, since I've gotten the truck, it's kind of difficult to put in first gear. If you are sitting at a light and in neutral and the light changes and you push the clutch to the floor and put it in 1st (fairly quickly - a normal reaction time), it will actually do a little grind and/or thump. However, if push the clutch to the floor and wait a couple of seconds and then shift into first, it's a bit of a "push" but it will go in without grinding.
Once in a while shifting to 3rd it feels the same way, but won't really grind.
I'm just wondering if that means the clutch is toast or is it the trans that is toast? Reason I ask is my 96 Cobra with the T-45 5 speed would grind going into 5th gear if I just normally put it in. I used to have to put it in neutral and then push the clutch in again and slowly shift to 5th for it not to grind. And it wouldn't go into 3rd if I tried to shift fast or under power. I replaced the clutch and found out the trans was actually going bad, but it had 173k on the clock.
So, I'm really paranoid that it's my darn trans in the truck instead of just the clutch. Whenever my old Camaro clutches used to be dying, they would slip more than they would ever grind going into a gear.
Ford Transmission :: 1995 F150 Slipping In 4th Gear - Speedometer Bounces Around 3 To 5 Mph
I think my E4OD in my 95 f150 is slipping in 4th gear. Just started the last couple of days, the engine rpms stay steady but the speedometer bounces around 3 to 5 mph. Thinking rebuild of the trans....
View 7 RepliesSanta FE SM (2001-06) :: 2002 2.7 4wd Acts Like It Is In Neutral
I bought this santa fe for parts for my other identical santa. When you take it out of park into r everse drive 1st 2nd gear it will idle down 200 rpm. It had no codes till I revved it up and moved gears. Codes trans module shift selonoid b and c. It makes no noise or vibration. The torque converter does not grab what so ever if it is even moving. I want to fix it now that I see its better condition.
View 1 RepliesFord Ranger / B-Series :: 1986 - Transmission Overhaul - Hard To Get Clutch Into Gear From Neutral
Rebuild on the Mazda 5 speed transmission. My 1986 Ranger 2.3 Four cylinder has 280,000 miles and the clutch has never been replaced. It's not slipping but I'm having trouble getting it into gear from neutral. Was told that the release springs on the clutch plate have weakened causing the clutch to not release completely so figured it's time to replace it. It's done well the last 280,000 miles. The question I have : overhauling on one of these Mazda trans and how difficult was it. Any special tools required, etc...I see Autozone has a rebuild kit which appears to have bearings, seals and gaskets. Figured while it was out I would go ahead and rebuild it myself if I can. Rebuilt a few engines but never touched a trans.
View 4 RepliesFord - F150 :: 1996 - Stuck In Fourth Gear - Melted Plastic In The Transmission?
I posted earlier this month about my 1996 Ford F150 4x4 manual tranny truck. It had gotten stuck in fourth gear, and I, along with others, assumed it was the shift forks. I cracked open the top of the transmission yesterday, and what do I see? Melted plastic staring back at me. What's going on here? There was melted plastic jammed between fourth gear and the inner wall.
Is this a case of the surgeon leaving his instruments inside the patient? Could a mechanic have dropped his tuna sandwich wrapper in the transmission at some time?
Ford Transmission :: 1979 F150 - Lost Reverse And Won't Stay In High Gear
79 F150 400/C6 2wd. Loss of reverse and it doesn't want to stay in high.
Strange thing happened today. I took my truck on it's longest test drive since rebuilding the transmission. It was about 25 miles. I got to the junk yard just fine and it was running just fine when I left. I went through a drive through to grab a burger and headed home. That's when it started acting funny. It shifted fine 1st to 2nd, then 2nd to 3rd, but it wouldn't stay in 3rd. It would shift into high, but the slightest bit of throttle and it would shift back into 2nd and eventually got so bad that it just stayed in 2nd, so I had to return to the town I was leaving.
I drove to an autoparts store nearby. I decided to move where I was parked and when I put it into reverse, nothing was there. It rolled back. I drove it to the new spot and called for a tow truck. Weird thing is that reverse worked just 10 minutes earlier when I left the junk yard. When I got it home 2 hours later, it backed up under it's own power. I let it cool down completely and took it for a test drive and it drove perfectly. I have a few theories or questions:
Kickdown rod: Can it be in such a position that it could take away reverse? I would assume that if the spring wasn't returning it all the way forward that it wouldn't have shifted from 1st to 2nd properly. I ask this because I am not using the Holley spring mount and I'm wondering if the wrong spring set up allows the kickdown to be partially activated.
Fluid: What fluid are you suppose to use after a rebuild and what fluid can't you use. Mercon V says it supercedes earlier fluids, but is that wrong?
Am I wrong to assume that if fluid was the problem that I would have had problems with 1st and 2nd?
Cooling: What are signs of hot fluid other than smelling it. Once again, assuming I would have problems with all gears if fluid was too hot.
My guess is that something is sticking in the valve body, but before I drop the pan and pull out the valve body, I want to make sure all other avenues are exhausted.
Ford Transmission :: 2007 E350 - Shudder When Accelerating In OD - Whine In Park / Neutral
Looking for your collective expertise
2007 E350 with 5.4L and 4R70W trans. 107K miles and the fluid has probably never been changed ( my mistake - thought it was 100K interval - finding out from my reading that is def not true ). Anyway, following is recent development (last couple days):
Symptom #1: In Park/Neutral there is a whine. As soon as you put it in P or N, the whine 'spins up', stabilizes, and does increase with engine RPM.
Symptom #2: Hesitation (albeit minor) when starting from stop in D and R, with _very_ minor shudder. Sometimes feels like it's struggling a bit to move its own weight just until it's rolling.
Symptom #3: Shudder when accelerating in OD. No shudder when I turn off OD. It does not stop when applying brakes (a test suggested elsewhere). Also, the shudder does not happen when applying gas while braked in D at standstill. Only at highway speeds (enough to be in OD).
This all started at the end of a trip (90 miles or so in 85-90 degrees) when I was pulling a utility trailer (maybe 2000 lbs loaded). Not sure if related, but traction control warning went off a couple times. I think I have a axle seal leak that may be triggering that.
Otherwise shifts fine (no change in shift behavior or smoothness). Things seem to be worse when it has heated up. Should I start with a fluid change? Wasn't sure because there are comments out there saying don't do it or the tranny will just fail faster (I am skeptical).
Elantra XD (2001-06) :: Manual Transmission Always Pops Out Of 2nd Gear To Neutral
I have a 2005 Elantra GT hatchback that I love with a 5 speed transmission. Lately every time I'm in 2nd gear, the transmission will pop out of 2nd into neutral. This only happens in 2nd gear. I heard it could be the shift collar (i.e. teeth?) that aren't grabbing in that gear.
View 5 RepliesElantra MD (2010-15) :: Transmission Shifter - Gear Selector Would Get Stuck In Neutral
Just got my 2013 Elantra Limited last weekend. It appears the car is having some issues with the transmission shifter. I am not sure if its tranny related, but I highly suspect it is. Dealer gave me the usual bs not being able to duplicate the symptoms.
1. Intermittently, gear selector would get stuck in neutral, when I try to put the car into P, after a long or a short drive.
2. I would have to wiggle the shifter to get into P, or I would have to shift to D, and then I am able to shift back into P.