Ford Super Duty (1999-2016) :: 2002 F250 2wd - Steering Stabilizer?
My 2002 250 just got ball joints, bushings, sway arms, 4 wheel alignment and new tires to top it all off. Did All this to correct the shakes, shimmies, popping and grinding in the front end. Now they say I need a steering stabilizer up front. Does any other than ford make a bolt on one and haw much and where can I get one.
View 10 RepliesFord Super Duty (1999-2016) :: Difference Between F250 Custom And Heavy Duty Steering Stabilizer?
Is there a steering stabilizer for a 92 Ford F-250 custom 2wd? and what's the difference between a f250 custom and a f250 heavy duty?
View 2 RepliesFord Super Duty (1999-2016) :: Putting Steering Stabilizer - Single Or Dual?
So I'm interested in putting a new steering stabilizer on my truck and am pretty set on the Rancho RS7000 series, but I am torn between getting a single OEM replacement or the full dual stabilizer kit. Single replacement? Did it make a difference? I've heard really good things about the dual kit, but obviously the price difference is huge. I don't do a ton of off-roading, but I do drive constantly on crappy city roads which can be just as bad
View 14 RepliesFord Super Duty (1999-2016) :: Single Steering Stabilizer (in-line) With Brackets Part Number?
I'm wanting to get a single in-line steering stabilizer for my '05 F250 4x4, but I can't seem to find any that include brackets.
I don't need a dual setup because I'm not running a big lift or big tires, but I want an inline stabilizer so that I can just leave the stock one in place.
What is the part number for one that comes with the mounting brackets?
Ford Super Duty (1999-2016) :: Suspension Stabilizer Bar - Up And Down Play
Checking the front end with the front wheels off the ground I noticed that my Suspension Stabilzer Bar has about an 1/8" up and down play in it. No side to side play at all. I checked the nut on the ball joint and it is tight but wondering if this is why I am feeling a slight tight/loose feeling when going down the freeway at 65.
It has this "tight" or a slight grab feeling when the steering wheel is centered and I move it left or right slightly (like normal steering wheel movement to stay in your lane) I don't feel this at slower speeds 30-40 etc just when I am straight on the freeway at about 65-70 mph.
Ball joints and everything else looked fine, no play noticed. Never had the "death wobble" but having this up/down play in their stabilizer bar.
Ford Super Duty (1999-2016) :: Sway / Stabilizer Bar Links Rattling?
I'm on my second set of links. The replacement were Dorman 3 years ago. They are rattling again. Do I just replace them again? I forgot to add, the bushings were replaced this year.
View 1 RepliesFord Super Duty (1999-2016) :: 2011 F350 - Rear Stabilizer Bar Removal?
I have a 2011 F350 with camper package (didn't want it). When I drive on a bumpy road (without 5th wheel), the truck suspension does not absorb the shock. The ruts just throws the truck side to side. Really hard, so I can't go on a dirt, rough road. On one bump it poped off my rear tire cap.
My problem may be with the camper package trying to keep the truck from going back and forth.
There is a 7/16 inch steal rod going from the truck bed, around the differential, and back up to the other side of the truck. Is that the rear stablizer rod?? Can I disconnect it? What would be
Ford Super Duty (1999-2016) :: 2001 - Steering Lock Rod And Actuator Replacement
I have a 2001 SD 7.3 Manual, in which either the rod or the actuator has broken. I can tell yet which it is. I can mover the lower actuator back and for but that doesn't tell me which part is broken. I have the parts on order to replace. I have been searching without success to find detailed instructions to make the replacement.
I run a small shop away from my day job but have never dug into one of these. Being the various small parts and sequence of disassembly/Assembly I want to do it correctly the first time. It's very strange how you can go to YouTube and search for everything under the sun with great results, except for this.
Ford Super Duty (1999-2016) :: Tight Steering Knuckle With Ball Joint Replacement
My 2004 f250 ball and u joint replacement job is at a bit of a stand still. Tore it down, brought the knuckle and axle shafts to an ex mechanic I know, because he has a 20 ton Harbor freight shop press. He mostly used a hammer, bashed out the old ball joints (I already had removed the u joints). U joint turned out fine.
I did notice the upper ball joint protruded a very slight bit on one side in the knuckle, meaning you could feel with your finger on the underside of the joint and on the one side it is not exactly flush with the interior of the knuckle. I would say it protrudes no more than a thirty second or so.
I brought it home, installed the boots on the moog joints, (the bottom was unusually difficult to put on), greased the joints and hung the knuckle on the axle tube, by a few turns on the lower joints nut. I then inserted the camber sleeve on the top stud, torqued the bottom to 49 fp then the top to 67 and finally the bottom to 150. End result, very stiff movement on the knuckle. No tie rod attached, and it takes to hands to move it from the "stopped" position,(turned all the way). I am sure it is stiffer than when I did the other side.
I tried loosening the nuts completely, same stiffness. I redid the torque sequence, no change. Tried hammering the ears around where the joints seat no improvement. The fellow who installed into the knuckle came and took a look. He agreed the knuckle was stiffer than you would hope, but, he suggested Putting it all together, as he believed they would loosen up before too long. I am not sure whether to try that, or remove the knuckle now, and redo with new joints. Pros and cons to either approach.
My question is : Does a knuckle become more sketchy by the time it is dealing with the pressing of a third set of ball joints? If I finish the install now, will a stiff knuckle action lead to other mechanical wear within a thousand miles or so, while I wait to see if they loosen up?
Ford Super Duty (1999-2016) :: F250 - Instrument Cluster And Steering Wheel Bulb Replacement
I found one thread in FTE regarding replacing instrument cluster bulbs but the solution was to contact Circuit Board Medics. I have one dark area on the right side of the tach and another dark area on the left side of the speedo. Probably the same bulb that's out. Also, can attempt to replace the bulbs (assuming its a bulb and not a fiber optic of some sort) in the steering wheel volume and fan controls?
View 3 RepliesFord Excursion :: Replacement Shocks Dual Steering Stabilizer
I'm looking to replace the worn out skyjacker or rancho steering stabilizers on the ex. Wanting to put bilsteins in there place. 5100 series to match the shocks for the truck. What are the part numbers for this setup?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Steering Stabilizer Removal / Replacement
Trying to replace my steering stabilizer and in the process I broke the nut close to the steering box. Would not budge so used a bar and well I broke it. Now I can't pop it out am I doing something wrong? Here are a few pics. I'm totally bummed nothing seems to be working for me.
View 14 RepliesFord Brakes/Suspension :: 2008 F250 - Steering Stabilizer Replacement?
Looking to replace the steering stabilizer on my 2008 F-250. It has a 6" lift and 37" tires.
Also, does "dual" mean better?
Ford Super Duty (1999-2016) :: Lug Nut Replacement?
Any downside to using a nut that covers the entire stud on my '99 450?
View 2 RepliesFord Super Duty (1999-2016) :: 2006 - Stiff Steering After Installation Of Red Head Steering Box?
I have an 06 F-250 5.4 gas w/138k. It had recently had a lot of play on the wheel (15 degrees maybe) and last week I made the move to replace the gearbox with a redhead box. All seemed to go ok, but now the steering is stiff and it won't come all the way back to center after a turn. It turns smoothly and completely with no binding, but it has to be moved the last 1/3 turn back to center.
I flushed the fluid initially with Valvoline max life fully syn. Then second guessed myself after the problem started happening so I switched it back to regular Mercon. No improvement.
I had it on stands today and it was extremely difficult for me to turn my tires left to right manually (at the wheel). The only other thing I did was adjust the sleeve on the drag link to straighten out the steering wheel.
Should I be able to turn the tires left and right from the wheel easily? Every now and then I hear a whine from the pump which I never had before, but 99% of the time it seems fine and is quiet. it just feels like something is over tight but everything should be to spec.
Ford Super Duty (1999-2016) :: Replacement Turbo For 7.3L?
After 225,000 miles, my turbo appears to have failed -- not spinning. This is a stock turbo that is unaltered. Yes, I change my oil and filter every 3000 miles.
My question is; what is a reliable after-market replacement part that will bolt up?
Ford Super Duty (1999-2016) :: Seat Belt Replacement?
My "new" truck has a sluggish seatbelt on the driver's side. It won't retract all the way.
How do I get to the mechanism to have a look at it or put in a replacement?
The belt on this one comes out of the top of the seat, not from against the door.
Ford Super Duty (1999-2016) :: 2007 - Tailgate Replacement?
07 Superduty, Oxford white. I have been looking all around NC pick a parts for a decent replacement tailgate. I know more recent years will fit, with hinge mods. Question is, what is the most recent year that will fit with hinge swaps only?? Looking for a source in SC/NC/VA for a replacement?
View 7 RepliesFord Super Duty (1999-2016) :: 2008 - LED Replacement Bulb?
Using LED replacement bulbs? I have a 2008 super duty. Want to upgrade lighting.
View 14 Replies