Ford Super Duty (1999-2016) :: No Response From Accelerator / CEL And Wrench Light On

I have a 2005 F250 5.4L 2wd. Parked the vehicle in my driveway and the next morning there was no response from the accelerator and the CEL light and the wrench light on. I pulled the codes and came up with codes P2104, P2107 and P2110. The KOEO code was P2122. I checked the wiring and connectors and all appear to be fine I replaced the throttle body and no change. I removed the accelerator pedal and tried it on another vehicle and it worked fine. I have power to pin 16 on the diagnostic port. After clearing the codes and rescanning the same codes come up immediately.

View 14 Replies

Ford Super Duty (1999-2016) :: Intermittent Stalls At Idle And Hard Start

As a follow up to my problem of intermittent stall and hard start, it is getting more pronounced. Now, every once in a while, it will start. Mostly it will not start.

This morning I connected an OBD2 meter with the key on and engine off. It told me that there are no DTC's. As I was attempting to run enhanced DTC's the code reader lost link with the computer. The connection icon was on but it lost the link. At one point, after several tries, I got the link back but it didn't last too long before it was lost again.

This is the same symptom that I have with running the engine. It will run and then shut off. After a hard start, it will start and run just fine and then shut off again.

My question is this. Can I still have power to the PCM and loose power to the processor? Is there a fuse or relay that could be causing this problem? If not, could the problem be a faulty PCM.

View 3 Replies

Ford Super Duty (1999-2016) :: 2015 - No Response To The Throttle At All

I have a 2015 SD with only 4100 miles on it. This has happened to me twice. Both times, traveling slowly at idle or just above. Anyway, tried to give it a little gas, and -----nothing. Lightly pumped the throttle a couple of quick times and back on line. The motor didn't die, but there was no response to the throttle at all. The first time, I thought maybe it was something I did. Then it doesn't happen for a month and a half and then again, in heavy traffic in the rain. Haven't had my first service yet, and you can bet I'll tell them about it. Almost felt like a two-stroke that had loaded up?

View 2 Replies

Ford Super Duty (1999-2016) :: 2003 - Pedal Would Sometimes Lose All Response And No Gauges

2003 f250 4x4 7.3 auto

Been an ongoing problem with truck, pedal would sometimes lose all response. truck starts and idles fine but will not throttle up and all needles on the instrument cluster are at their rested position and the odometer doesn't even light up, however all the backlights still work fine.

The owner said that a 10 amp fuse on the bottom row of the fuse panel would occasionally blow, and that's when the pedal would go dead, he would replace it and keep driving till it blew again... usually about a week. I checked all fuses on the truck tonight and all are fine.

Unplugged the connector on the pedal sensor and cleaned and reinstalled and still wont throttle up. I am not sure what number the fuse was that he kept replacing but i *think* it was a cluster fuse. Is their an correlation between the cluster stopping the pedal sensor from working or vice versa?

View 14 Replies

Ford Super Duty (1999-2016) :: 2015 F250 - Lousy Throttle Response

Took delivery of my 2015 F250 in June with 2WD and the 6.2 gas engine. What I thought to be a slow throttle response seems to be more of a quick shifting transmission according to two different dealerships. My 6 speed automatic has already shifted to 4th gear at only 25-30 MPH. My Dodge Hemi I sold never had shifts as quick as this and I think it's to quick. My question is....is there a way to change these shift points so I get more speed before it shifts into the higher gears?

View 10 Replies

Ford Super Duty (1999-2016) :: 2005 V10 - Poor Throttle Response And Mileage

My friend has a F250. He was getting terrible mileage and the mechanic he took it to replaced the intake gaskets. After that the mileage went to 12 and he was happy. Now its down to 6-8, just highway. It seems to me the throttle response is terrible compared to my dad's 01 V10. And it sounds terrible. Exhaust manifolds aren't leaking that I see.

I've got AE and have hooked it up, but I'm really not very familiar with these trucks. I don't get any codes that would relate to anything. Had one trans sensor code but that was about it. Key on engine running test didn't say anything.

View 5 Replies

Ford Super Duty (1999-2016) :: 2005 F250 - Quick Throttle Response

2005 f250 4x4 , crew cab v10. Just put on my magnaflow muffler and gotta say, What a difference that makes! Can't wait to get the k&n intake kit and see what that will do. I see that my truck has the electronic throttle control instead of the previous v10s with the cable. I am wondering, is there any way to get quicker throttle response like with the old cable style throttle? Just seems real sluggish to rap up the rpm in park with no load on it.

View 1 Replies

Ford Super Duty (1999-2016) :: 2008 - Knocking Sound Goes Away If Tap The Accelerator

I have had this truck for several years. I have only had a few issues. I've heard of engine noise issues but I have never had any until now. My 5.4 is making a knocking sound that just started. It goes away if I tap the accelerator. It has over 200,000 miles on it. I change the oil every 3000-4000 miles. No additives and always conventional 5-20. Is this a serious issue? I've seen people talk about using thicker oil but I'm very hesitant.

View 13 Replies

Ford Super Duty (1999-2016) :: 2010 Truck Did Not Shift When Hit The Accelerator

I have roughly 104k miles. The weather is trying to get colder. Lows of 45 highs of 80 right now. Last week I was accelerating on to the highway and the truck seemed to have trouble shifting. I hit the accelerator and it did not shift. It would continue to increase in speed but very slowly and would even tend to kind of sputter a little. My engine light came on and has gone off and on several times since then. This has occurred several more times and is always when I hit the highway.

View 5 Replies

Ford Super Duty (1999-2016) :: 2002 F250 - Vibration When Letting Off Accelerator

So, I'm slowly but surely eliminating a terribly shaky front end on my 2002 F-250 7.3L 4x4. First was a new carrier joint on the front drive shaft. Didn't work much, but the shop said the darn thing was falling apart. Next thing I did was new wheel bearings and manual hubs. Less vibration for sure. But the last remaining issue, in terms of vibration, is that when I let go of the Accelerator going at any speed above 60 MPH, it makes a horrible horrible noise, and I could feel a vibration. It shakes the whole truck, but I can very noticeably feel it directly in the gas pedal. It's really only an issue during deceleration. What could it be??? Drive shaft U-joints? Torque Converter? Something else in the Front End? Something in the engine even?? I don't exactly have the funds to tackle every possible solution.

View 1 Replies

Ford Super Duty (1999-2016) :: Scary Clunk In Drivetrain When Take Foot Off The Accelerator

I have a 2001 F250 7.3 with 175K.

Here is the situation. There is a disturbing clunk when I take my foot off the accelerator and a corresponding clunk when I push back down on the accelerator. This only occurs when the vehicle is not under load. That is, it does not happen when going up hill or on any sort of an incline. It does not happen when the automatic transmission shifts. It does not happen shifting into reverse or drive.

It does not happen when starting or stopping. It only happens when I am at 40-60, or so, miles an hour and let off the accelerator and/or press the accelerator again. It appears that I can carefully feather the accelerator to eliminate or, at least, minimize the clunk. I have crawled under the truck and it looks like all the U-joints are tight, I have lubricated the slip-yoke (although when twisted there is, like a mm of play when this is twisted, not much but a very little).

The rear-differential pinion appears to be tight (no side-to-side play or up-and-down play, or at least I can't make it move with my hands). However, when the truck is in neutral the entire driveshaft is able to rotate a half inch, or so, all the way up and down the drive train. That is, the transfer case and the rear differential appear to have a little rotational play in them, but I am guessing this is pretty normal. When in park the entire driveline seems solid.

I have seen from some of the other posts that this sort of clunking can come from leaf springs, hangers and such but since this clunk seems so isolated to acceleration changes when the vehicle is not under load, I doesn't seem like this would be the issue. No clunk when shifting, turning, bumps etc. Everything seems perfect until I am on a gentle downhill or flat and let off the accelerator. Doesn't appear to clunk when going down a steeper decline. All this gets me to thinking that the clunk is caused whenever the driveshaft rotation gets ahead of or behind the rotation in the rear differential.

View 14 Replies

Ford Super Duty (1999-2016) :: Ticking Noise Coming From Right Side When Push The Accelerator

2002 Ford F-250 5.4l ... What is the difference in sound between a lifter tick and an exhaust leak? I have a ticking noise, almost sounds more like a puff of air noise, it only makes the noise when I push the accelerator and is coming from the right side. Noise is most noticeable if I put my head under the passenger side front fender. I am guessing I have an exhaust leak somewhere between the heads at cat but just wondering about the difference in sound. I'd think if it were the lifters they would tick at idle, right? The truck sounds great at idle (after doing a tune up) I just want to get rid of this annoying tick when I accelerate.

View 3 Replies

Ford Super Duty (1999-2016) :: 2003 F350 - Hard Or No Start / Shaking In Low RPMs / Slow Response From Gas Pedal

I need fixing my 2003 f350 6.0 diesel, I have been working on this truck for a while and still am having problems, here was the original symptoms:

-Hard start or no start on a sunny day
-Rough idle for 10-15 minutes
-Rough shaking in the low RPMs (35 mph)[/COLOR]
-Slow response from the gas pedal
-boost would only get to 14

My dad and I then did many things to the truck in the shop, those things are:

-Air test and replacement of coupling going into oil branches (next to HPOP)
-Replaced EGR valve (no good)
-Replaced ICP sensor (leaking oil)
-Replaced ICP sensor and IPR valve piggtails (due to frayed wires)
-Cleaned Turbo
-Cut MAP sensor hose and reattached it (spliced on the end)
-New battery
-Performed a bubble test and found two bad injectors on passenger side (injectors #5 and #7)
-Cleaned and lubed tops of injectors
-Replaced O rings and copper crush washers on all injectors
-Replaced nipple cup O rings (tight)
-Blew out injector cups
-Bubble tested after injectors put back in (no more bubbles)
-New FICM, EGR cooler and oil cooler were already installed
-Ohm'd main engine wiring harness (good to go)
-Taped up frayed wires on fan clutch connection
-Increased wire gauge on the positive jumper between both batteries
-Sanded each ground on the batteries and engine, cleaned battery clamps, lithium greased connection points.
-Checked fuel for air (no air)
-Checked fuel psi (85 psi, plenty)
-Oil changed

After doing all of this (diagnosing as we fixed each thing) we now fixed many things including the hard/no start problem. Now, for the first three to five minutes:

-It starts right up
-Runs perfectly, no shake and instant response from the gas pedal and turbo
-Boost goes to 28
-ICP is 800-950 on idle
-IPR is 25-26.9% closed
After five minutes however:
-Starts to shake
-IPR % starts to raise
-Received no response from gas pedal (absolutely no power)

This truck has been torn apart like 8 times and I have to do it on my spare time.

View 13 Replies

Ford Super Duty (1999-2016) :: 2004 - Loud Rattle Under The Hood When Lift Off The Accelerator Pedal

I bought a 2004 F250 super duty 4x4 with the 6.0 a couple weeks ago and have a few questions. Hopefully all of these things are normal, but I thought I would ask you experienced drivers.

1) Occasionally while driving when I lift off the accelerator pedal I can hear a sort of loud rattle under the hood. I assume this is the turbo shutting down? Is that normal?

2) 4x4 and locking hubs... I have the 4x4 hi and low switch on the dash. Do I need to also manually lock the hubs to go into 4x4? After reading the manual it seems like I can just turn the dash switch and they should automatically lock, but I'm not sure. The hubs are not marked, but going by the pictures in the manual I think I know which is "lock" and which position is "auto" or off.

3) Front wheels hop at full turn. I expected wheel hop in 4x4 or with the hubs locked, but even in 2WD with the hubs in the auto position the tires still "hop" or knock a bit at sharp turns. Is this normal?

View 2 Replies

Ford Super Duty (1999-2016) :: F250 - 4R100 Unexpectedly Coasts - Accelerator Pedal Will Not Rev The Engine

I have a 99 F250 7.3PSD; I upgraded the tranny cooler after an episode of overheating while backing up a hill.

The truck has done well, hauled a few tractors with it, but recently I have noticed something that seems scary. When going downhill, I often relax on the accelerator. Usually there is some passive engine braking as happens with any auto tranny. Recently, the truck just coasts - it is as if you feel the tranny shift into neutral and you just coast, except I didn't shift. While this is happening, the accelerator pedal will not rev the engine. You can put the pedal all the way down -> rpms at about 6-800. No response.

At the bottom of the hill (so far) the engine gets louder. the rpms drop, and the accelerator works again. Every time, so far. But, if IO am going down hill, and want to accelerate to execute a laneg change or something - I can't. AFAIK, everything A-OK after the new tranny cooler. levels, etc.

View 1 Replies

Ford Super Duty (1999-2016) :: 2004 - Accelerator Won't Respond In Drive - Throttle Position Sensor?

Recently on two occasions I pressed the accelerator clear to the floor with no response. After shifting into Park then back into Drive it drove normally for about a week. Now it has stalled out and was very stubborn to restart. Once running, the accelerator will sluggishly rev the engine while in Park, but in Drive, will not respond. TPS sensor or something else?

2004 6.0 Diesel, 75K miles, no mods, well maintained.

View 5 Replies

Ford Super Duty (1999-2016) :: 2011 F250 - Engine Idles Rough Until Warms Or Accelerator Is Pressed Down

On a cold crank the engine idles rough until it warms or the accelerator is pressed down. Also runs rough going up hills or towing. Check engine light is on and is throwing the code for bank 1 to lean and cat performance below threshold. Cats have been tested, good. Fuel trim tested, good. One mechanic said noth8ng is wrong with it well, there is. 2011 f250 6.2 gas...

View 5 Replies

Ford Super Duty (1999-2016) :: Stalling Under Load / Intermittent

My current truck is an early 99 F250, 7.3L diesel, CC 4x4(manual shift transaxle) auto transmission. It is basically stock, with the exception of a hutch/harpoon and a new fuel pump over the winter, an AIS intake. I have a magnaflow exhaust kit in the garage along with bellowed up pipes but have not installed them yet.

Here is my issue. Several times over the last 2 years, the truck will pull a load, or long trip, and with complete randomness, the engine will feel like it has shut off, there is usually a jerk or two, and the truck "restarts" itself and continues on like nothing happened. Last year we drove 1.5 hrs from home with the boat in tow, driving up Snoqualmie pass, and it died completely, no restart. We had to be towed home. It started right up at the shop, so no real clue of what happened.

When this happened, I had the fuel system checked for pressure and replaced the engine fuel filter, and all was good. I also had the Cam position sensor replaced/updated to the new grey sensor. Shortly after, I had the minor jerk/stall occur again, so I replaced the fuel pump and did the hutch/harpoon mod to ensure there wasn't an intermittent fuel pressure loss and that the in tank filters were not clogged.

Last weekend, i pulled my boat to Oregon, and the same "hiccup" happened as I was about 1.5 hrs into my trip. it was fine after that the rest of the 4 hr trip. We also drove back the same route and had no problems.

View 2 Replies

Ford Super Duty (1999-2016) :: Cruise Control Become Intermittent

I've got a '08 F250 XLT that the cruise control has become intermittent. It works most of the time but at times it will "go out to lunch" and not do anything. I've taken the controls from the wheel and didn't see any gummed up coke spills or anything there. It may not be anything but twice when it failed while on a trip I pulled over and shut the truck down. Started it up and the cruise would go back to working. Once I did this and it went back to working only to shut off in about 2 seconds but I was able to engage it again and it kept working. When it stops working there is no green indicator on the dash either.

View 9 Replies