Ford Super Duty (1999-2016) :: Right Front Caliper Sticking / Brake Burning Smell
I know this has been talked about many times and how to solve the issue but thought I would ask some other questions too. Earlier in the summer, I did grease the slider pins as preventative maintenance. I don't drive my truck all that much and when I used it yesterday, (about 30 minute drive) I came home to burning brake smell. I'm wondering if enough heat would cause the caliper to go bad? Should I just grease the pins again or change out some parts?
View 6 RepliesFord Super Duty (1999-2016) :: 2003 F250 4x4 - Left Rear Caliper Sticking After Replacing
Two weeks ago did a road trip to NH from RI and i heard a slight dragging only at low speed (10-15mph) in my left rear tire. figured the caliber was dragging a little, it was. Before arriving in NH the brake light came on. Long story short i get back to RI and the left side noise gets worse and starts to lock up. I finally replace the rotor which was warped, pads, and caliper which was bad.
Was driving it same day and still here the same dragging and screeching noise and the brake light is still on. On my way home the left side locked up at low speed without hitting breaks and slid the truck, mid you all parts are new on that side. I am not sure what it could be at this point something in side the axle?
Ford Super Duty (1999-2016) :: 2005 - Repairing Front Caliper?
Is this repairable or would it be better to just replace it ? Ive never rebuilt one of these.
View 11 RepliesFord Super Duty (1999-2016) :: Front Brake Caliper Bracket Bolts
I read a reference to the front brake caliper bracket bolts being one time use torque to yield and must be replaced every time they are loosened. Is this true?
This is on my 06 F-350 in my Sig.
Ford Super Duty (1999-2016) :: Front Disc Brake Caliper Pistons Won't Go Back In
2001 F250 SD diesel. Brakes have been working fine with no pulling. They just started to squeal recently so I knew it was time for some new pads.
I'm having a problem that seems to plague me often when I try to replace disc brake pads. I can't get the twin pistons to go back in to allow room to get the new, thicker pads in.
I unscrewed the cap to the master cylinder and used a spreading tool (that came in a brake kit from Advance Auto Parts) to compress the pistons. No movement.
I put a lot of force on it. No piston movement.
I unscrewed the bleeder screw and tried again. No movement.
Ford Super Duty (1999-2016) :: 2007 F350 - ABS Light Came On / Right Front Caliper Stuck And Got Very Hot
My question is my abs light came on so I stuck my computer on it. Said right rear , we'll we all know on a 2007 6.0 f350 4X4, the there's only one sensor on the pumpkin, so I replaced it and cleared the code. Abs light came back on once I started driving, week ago my right front caliper stuck and got very hot, could that read bad for the rear of the front went bad? Will pull plug and make sure I didn't bend any pins.
View 2 RepliesFord Super Duty (1999-2016) :: Getting Front Brake Pads Into Caliper - Springs Kept Popping Out
03 f350 4x4. New front calipers and pads.
Wondering if there's a 'trick' to getting the front brake pads into the caliper . Those damn springs kept popping out. I'd get three of the four ends into place in the pad holes then one would pop out while I'm trying to get the fourth in.
After about a hour of trying every different way that I could think of, another set of hands came by and with four hands holding things in place, it finally did the trick.
Ford Super Duty (1999-2016) :: 2000 F250 - Front Passenger Side Caliper Keeps Locking Up
I have a 2000 f250 4x4 with 4 wheel abs. The front passenger side caliper keeps locking up while I'm driving and won't release and when I hit the brakes it pulls hard to the drivers side. I have put two calipers on the passengers side and put new brake lines on.
View 8 RepliesFord Super Duty (1999-2016) :: F350 - Left Front Rotor Rubbing On Caliper Bracket
1999 F350 4x4 dually. Replacing brakes front and back. Rotors, Pads, and hoses. On the left front put rotor back on and torqued down hub nuts on rotor. Then caliper mounting bracket wouldn't fit back between mounting bracket and rotor. Loosened the hub nuts on rotor, and fit mounting bracket in place. Then torqued down the hub nuts again, and rotor rubs on mounting bracket and rotor/hub won't turn.
View 2 RepliesFord Super Duty (1999-2016) :: Left Front Caliper Is Not Squeezing Hard Enough To Stop The Truck Evenly
Having a problem with calipers again/still seems like always. Replaced all calipers twice in 86K miles on a 2000 f250 crew 4x4 because of stuck calipers. Replaced brake hoses and all hard lines in the rear about 2 years ago. My problem now is the left front caliper is not squeezing hard enough to stop the truck evenly. (pulls to the right) The rotor had some rust from sitting and after driving a for a while the rust is not completely gone as you would expect. Replaced caliper bled a couple of times. Caliper looks to be getting pressure enough to bleed and can see it move when brakes applied when engine not running. I don't have experience with Proportioning Valves but do you think that is the problem and how do I fix it?
View 8 RepliesFord Super Duty (1999-2016) :: All Brakes Sticking?
Read alot about a brake sticking and changing out the caliper or the pin or the hose but did not come accross a problem with all four sticking. When I leave in the morning brakes are fine and once the heat up all four get supper hot when I get to my destination and the truck is very sluggish, the brakes are sticking and it is all four. Changed the calipers on all four but did not work. Changed a brake line (not hose) that was rusting out, did nothing. I am leaning towards the master and its valve because all four are effected.
View 14 RepliesFord Super Duty (1999-2016) :: Rear Brake Caliper Locked Up?
About a year ago, I had my right rear brake caliper lock up on my F350 dually. The shop said it can happen and replaced both rear calipers. Last week I started to hear something from the rear and within less than a a few days, before I could get to a shop the noise increased and when I looked the rotor had been gouged on the right rear.
I cannot see the left rear rotor to compare as the wheels don't line up on that side to see through. So my question is this. Could it be the caliper failure was a symptom and not the cause. Maybe a proportion valve or something that could affect the pressure on that one wheel.
Ford Super Duty (1999-2016) :: F250 - Brake Caliper Won't Release
My 1999 F250 right rear brake caliper will not release. I replaced the caliper, caliper mounting hardware, pads, rotor, emergency brake pads, and I bled the system. For some reason the right rear remains activated when my foot is not on the brake pedal. The other three wheels appear to be functioning normal.
View 6 RepliesFord Super Duty (1999-2016) :: Cruise Control On / Off Button Is Sticking
Just noticed today that my cruise control on/off button is sticking. Push to off it stays pushed off, push it up to on and it stays up so i must physically center it myself. Is there a way to remove the button and take it apart to clean and regrease the contacts so it doesnt stick? Kinda dumb actually since i might have used it eight or ten times since buying the truck new....
View 2 RepliesFord Super Duty (1999-2016) :: 2005 - Brake Sticking And Dragging?
after replacing rotors,calipers,pads,hoses and hardware with OEM parts TWICE now I'm still having issues with my brakes sticking and dragging!!! I am starting to suspect the pistons within the calipers themselves. I think that Quality (expensive) aftermarket parts is going to be my soulition but would like to get some input from some fellow Super Duty owners before I pull that trigger.
View 7 RepliesFord Super Duty (1999-2016) :: 2002 - Brakes Sticking Partly On?
On my 02 Superduty 4x4 7.3, I just replaced all the rotors,calipers,& pads because two were seizing up, so I decided to do all 4. It's still happening?! What could be causing this? They were all bled of the air & flushed with new fluid. I spent a lot of money here so I don't want to wreck any new parts, so it is parked now until I can get it fixed.
As I was coming home yesterday, as it was shifting up thru the gears it was dragging & held up on 2nd before it went into high & was hard keep moving & the RPM's were higher than normal, then all of a sudden pop and everything let go,it quit dragging, shifted into OD. Before this point I noticed the brake pedal seemed to be higher and hard?
Ford Super Duty (1999-2016) :: 2003 F250 - Rear Brakes Sticking
2003 F250 V10 4x4. I have a rear brake sticking so I assume I have to replace the calipers. Which brand should I go with?
View 2 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Brake Started Sticking?
I have a 2002 Ford F250 Superduty with a 7.3 diesel. Brakes started sticking on it. I replaced all the calipers cause the boots were starting to crack but not leaking. All four brakes are still sticking. I can drive a little ways and then the brake peddle feels funny and they start dragging all four. I can loosen the bleeder and brake fluid will spray out and release the brakes for awhile.
View 4 RepliesFord Super Duty (1999-2016) :: 2007 - Brake Pad Burning Smell - Caliper Dragging
The wife and I ventured out last Friday evening to run a few errands. When we returned to the house and pulled into the garage, we both smelled burning brake pad. I felt the rear wheels, the drivers side was too hot to touch.
Dragging brake caliper. I got online and reserved a drivers side caliper and a set of pads at NAPA. Saturday morning I removed the caliper. Much to my surprise, one of the caliper pistons was broken into multiple pieces.
I took the offending caliper to NAPA and picked up the new caliper and a set of pads.
Side note - NAPA seems to think the 2007 trucks have calipers that mount in front of the axle, not behind the axle. They will try to sell you a passenger side caliper and tell you it is a driver side caliper. It will bolt up fine, but the bleeder valve will be at the bottom of the caliper instead of the top. You'll never get the air out of the caliper.
Got back home, bolted up the new caliper and pads, then bled the system. All worked well.
I decided to throw new pads on the passenger side brakes as well, since I had 2 remaining. I took off the passenger side caliper, much to my surprise I found a cracked and broken piston on that side also! Another run to NAPA to pick up another caliper. Installed, bled the system again, all working well.
Now, I have never seen a cracked and broken caliper piston like this, let alone one on each side of the rear axle. What might have caused this? About a year ago I had a shop install new backing plates. The pads and calipers are about 3 years old, same shop installed those.