Ford Super Duty (1999-2016) :: 2003 F250 Starting Rough Starts After Sitting For Few Days

I have a 2003, F250 SD, 5.0 with a weird problem no one can figure out. Now it doesn't matter what time of the year it is but after the truck sits a few days when I go to start it up it run roughs. Sometimes for a few seconds sometimes a few minutes then it "straightens" itself out. Recently it took almost a day to fix itself. No engine codes, no other symptoms.

View 4 Replies

Ford Super Duty (1999-2016) :: 2001 F350 - Crank For About 15 - 20 Sec Before Starting

It's a 2001 F-350 Crew cab short bed. Got it from the second owner which had a large file from the original owner on documentation and maintenance records. Truck has 280k, tranny about 80k. Question I have is, I kinda thought it would "feel" more powerful then it does. Temp got to about 35f last night after work and it cranked for about 15-20 sec before it started (yes I let the "Wait to start" light go out).

Then pulling out of work it would hardly get out of its own way. Does this sound normal? When it is warmed up it goes ok, but still I figured when the turbo winds up it would feel a bit "peppier". I get its a diesel and not a hot rod but I was expecting a bit more pep.

MODS on the truck that I can tell: AFE cold intake, 5"? exhaust turbo back, about 4" lift. Stock PCM. In cab controlled rear air bags, nice deck with back up camera.

View 6 Replies

Ford Super Duty (1999-2016) :: F350 Will Start Once Then Not Starting Again For Hours

I own a 1999 F350 with a 7.3 diesel engine, every time I drive it, it will start once then it won't start again for hours. At first I thought the starter was getting hot because of the exhaust is too close to it but I tested the wires going to the starter and i am not getting power to the starter when this happens. When it started doing this, it would only act up if it was above 80 degrees outside. Now it makes no difference. I have replaced the Valve cover gaskets, glow plug solenoid, and starter solenoid.

View 3 Replies

Ford Super Duty (1999-2016) :: 2008 F350 Braking Ability Starting To Drop Off

I tow 10-15K; 6-10x per month with this truck. I can feel the braking ability starting to drop off so I want to get them done pretty quick. I am more or less happy with OEM performance but if there is a better value, and with my SO starting to haul the horse trailer around.. I wouldn't mind upgrading.

What is worth the money? I'm fresh out of school trying to figure out what the best value is.

Calipers?
Rotors?
Pads?
Brake Lines?

What would provide me with a noticeable improvement without breaking the bank?

Last question, could worn rotors cause vibration/shaking in the steering (primarily when turning ramps) at 50-60mph? Tires are brand new, problem showed up before they were replaced.

View 7 Replies

Ford Super Duty (1999-2016) :: 2002 F350 - Auto Shifter Starting To Get Some Play In It / Loose

2002 F350 5.4 . I did some plowing today, truck ran Great, but noticed the Auto Shifter starting to get some play in it, 185 k on it. I recall reading about how to tighten it back up.

View 3 Replies

Ford Super Duty (1999-2016) :: 2011 F350 - Hard Starting / Cranks Through 2 Cycles Sometimes Before It Fires

My 2011 f-350 6.2l cold starts hard, it cranks through 2 cycles sometimes before it fires, then it might stall. Sometimes it stalls if I put it into drive or reverse before its warmed up. It has also misfired on one or several cylinders during startup. It has also misfired while driving. It has never stalled when driving. I have replaced the canister purge valve, I have done a full tune up with all factory plugs. All with no change to how it starts. My next step is a Pcv valve, I have one coming from ford today.

View 5 Replies

Ford Super Duty (1999-2016) :: 2005 F350 Not Starting With P2291 Error Code / ICP Reads 0 While Cranking

2005 F350 crew cab with 6.0 currently cranks but no start with a P2291 error code. Using scanguage 2 it shows icp 0, IPR 67.7, FICM 47.5 while cranking. Disconnected ICP and still no start. removed icp and hooked up air and I do not hear/see any signs of air leaking. When I disconnect the air it then whooshes out. About 2 months ago got a #1 cylinder contribution error code and changed out that injector and it has ran fine up until this issue.

Can this be a IPR? I am leading towards the HPOP, but as it costs a pretty penny would really love to make sure I tried every other avenue.

I have 197K on it, and 2 years ago did a EGR cooler delete. In May this year replaced the oil cooler, and then in August changed out the #1 fuel injector.

Oil cooler screen was broken. Cleaned the entire reservoir out. Could this just be a clogged IPR? or seeing the change while cranking an indication that it is working?

View 1 Replies

Ford Super Duty (1999-2016) :: 2006 F350 Not Starting - Code P2285 - Injector Control Pressure Sensor Circuit Low

I have a 2006 f-350 6.0 and i went to fill up my truck with diesel. After that the truck did not start. Currently has the code p2285 - injector control pressure sensor circuit low. I tried disconnecting sensor, still no start.

I have the torque pro app and another 6.0 that I use for comparison. Check power at ficm 48 volt, flp 11.5v, FVP 11.5v. Hpop while cranking shows 1400 psi. removed oil filter and see low pressure oil ok, fills up reservoir. ipr at crank about 65%. fuel filter full of fuel.

Replaced the dummy plug on passenger side because originally hpop was very low psi 12. after replacement it went up to 1400 on cranking. What should I be looking at next, should I be removing ipr? should i be looking at crank sensor or cam sensor? Just installed 2 new batteries also because my dad kept cranking the truck until it died.

Checked to make sure fuel cut off relay not triggered, Ok. The truck has been having long cranks before it died. Also right now the injector cycling is 10 seconds long while on my other 6.0 it is about 4.

View 14 Replies

Ford Super Duty (1999-2016) :: Battery Goes Down Sometimes After Sitting For Few Days

My battery on my 2008 SD goes down sometimes after the truck has been setting for a few days. This doesn't happen very often, and I've checked to see if I left something on that could have put a draw on it. I can find nothing that has caused it. I jump it off and might go a month before it happens again. I've got an add-on voltmeter that show voltage when the switch is on, and it's charging perfect. On older trucks, I would simply put a test light between the positive post and the cable and checked for a draw, but on the later model there is always a slight draw to keep memories alive.

View 9 Replies

Ford Super Duty (1999-2016) :: After Sitting For Few Days - Airbag Circuit Draining Battery?

Within the last few weeks my super duty battery has been dead after sitting a few days. Draw is around 80 ma. When I pull the air bag fuse it drops to 10 ma. Before I tear in to this thing need to know where to start.

View 3 Replies

Ford Super Duty (1999-2016) :: 2005 - Won't Start After Sitting For 5 Days - Slow Battery Drain?

Having problems with a slow drain on batteries? My truck wouldn't start after sitting for 5 days.

After recharging and starting it up once, I pulled the key, and disconnected the battery harness and checked for current on all the red wires in the harness. Only one drew current. I found the small red wire on the drivers side initially draws 470mA for 1 minute, then draws 22mA. In my experience in mobile audio, 22mA can drain a battery over several days.

Has anyone out there checked their 'dark current' draw? I have chased it all over and checked all the aftermarket add-ons and it comes down to something in the factory dash.

View 8 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 Truck Has Always Had Difficulty Starting Cold

2001 F250 7.3l 294k miles

Ok so truck has always had difficulty starting cold since I got it about 12k miles ago. Replaced glow plugs, that made things slightly better but still no start unless temp gauge was in that first line above the C. Changed to Rotella, immediately after oil change starts better and at slightly colder temps.

Since getting the truck when you turn the ignition on you can hear a 'whistling' type noise which I believe is the fuel system pressurising. That used to last as long as the chimes did when you first turn the ignition on. More recently it lasts a lot longer.

Towed recently and had intermittent check engine light - believe this could be HPOP related, haven't checked codes yet as we're on vacation. No oil in the valley. But I do have a little oil carry over in the turbo intercooler pipes.

Truck slightly sluggish at setting off initially and then picks up reasonably well when not towing but my Dyno says I'm putting a bit more pedal to get the same performance from say two months ago

Pretty sure injectors haven't been changed since truck was new but can't be absolutely certain as there is no history. I was surmising this is probably both a HPOP and injector age issue but only from what I've found searching...

View 14 Replies

Ford Super Duty (1999-2016) :: Click But Not Starting - No Crank

I work for the transportation department at a school and we have a bunch of 6.0 f350/450 busses and this bus I am working on has a no crank condition. Bus in question is a 2006 F450 6.0.

Currently if you turn the key to start the engine the solenoid just clicks but the engine wont crank. The person working on it before me assumed that the batteries and or starter were bad so they were replaced(0 miles on them right now) but the problem still persists.

First thing I did when I started working on this bus was jumping the starter relay and the starter engages and starts the engine perfectly. That being said I know the starter wiring is fine.

Secondly I looked through the wiring diagrams and saw that the PCM grounds the 85 terminal on the starter relay so I tried grounding the 85 and I was able to crank the engine with the key so that was telling me that the actual starter relay is fine. Next I went and swapped the PCM with another 2006 f450 thinking maybe the grounding switch in the PCM was bad and I have the same no crank condition. The PCM from the bus in question was swapped to the doner bus and it cranked perfectly(PCM in question is fine).

Next thing I did was look up all of the ground locations for the PCM or anything to do with the starter and they were all cleaned and still have the same no crank.

Looking around on the internet I see that the viscous fan can cause a problem if it shorts out so I unplugged that and no change in the no crank. I also saw that the trans range sensor could cause a no crank condition but I am getting back up lights/beeper and the bus "wants" to crank so I am thinking that the TRS is not the problem.

Lastly I tried hooking my Modis scanner up to this bus and was NOT able to communicate with either of the PCM's I tried. Not sure if this is related to my no crank condition. I checked all of the wiring that I could but could not find any chafing or breaks in any of the OBDII wiring. My planned next step is to replace the TRS...

View 10 Replies

Ford Super Duty (1999-2016) :: Rumble When Starting And Idling

I was wondering if there is a aftermarket product to give my truck a more Rumble when starting and idling.

View 8 Replies

Ford Super Duty (1999-2016) :: F250 V10 Starting Sporadically

I am looking at purchasing a 1999 f250 Crew Cab Long bed with the V10. It has 120,000 miles on it and has been very well taken care of and maintained. The current owner says that over the last couple of weeks it has started to start sporadically. The first time it did it was after a 30 minute drive. Parked the truck outside his garage and a hour later when he went to pull it in the garage, it wouldn't start. He called a mechanic friend that told him to trip the inertia switch.

Pressed the switch, it clicked, and then the truck fired right up. Since then it has done it twice more but now instead of tripping the inertia switch he turns the key on and off 10 times and then it starts right up. What this would be? I would normally think fuel pump since cycling the key on and off would be building pressure in the system if the pump was just starting to die but the inertia switch being tripped has me confused.

The owner thinks or was told that quickly turning the key off and on is resetting the computer and after turning the key 8 times the locks lock and unlock and the lights flash once. Is this what it is doing? I thought turning the key on and off in multiple succession let you manually read the codes...

View 8 Replies

Ford Super Duty (1999-2016) :: 2001 - Can't Get F350 Out From 4X4 Low?

I went out getting firewood in my 2001 F350 4X4 6.8l V10 auto . Backed up to the slash pile, put the truck in 4X4 Low and went to work.

When we finished I flipped the switch to 2WD, but the transfer case would not dis-engage and the IDIOT LIGHT on the dashboard stays on 4X4 Low... I can't get the truck out of 4X4 Low. I turned the hubs from auto to lockand its still stuck in low range.

View 8 Replies

Ford Super Duty (1999-2016) :: F350 - Battery Going Bad?

Our new 2016 F350 King Ranch is suffering from a battery drain. It goes dead after it's been left for over 24 hours. This has left us stranded several times.
The truck has been at the dealership for weeks and there is still no resolution. We really like the truck and bought it because we believed it would be dependable. This is extremely frustrating.

View 14 Replies

Ford Super Duty (1999-2016) :: F350 Will Not Go In Park

I have a 99 F350 with a 7.3 diesel that will not shift into park.

View 10 Replies

Ford Super Duty (1999-2016) :: F350 - Key Fob Won't Program

I have a buddies truck as a loaner while my f250 is in the shop. He doesn't and has never had a key fob. Just to clarify he bought it used years ago and its never been his DD so he never bothered getting a key fob. I picked one up w intention of programming it for him but i cant get it to work. Wondering if his truck doesn't have rke??

Ive tried the turn on and off 5 times and also 8 times w no luck. Its a 1999' F350 crew cab Lariat, all the bells and whistles so i would think it should have rke.

It is however a manual transmission V10. Wondering if it being a manual is messing me up having that little button one has to push to turn the key all the way back. Is there a different procedure for manual or maybe just no rke?

View 1 Replies