Ford Super Duty (1999-2016) :: 2002 - Stripped Coil Retainer Bolt
I've a 2002 Ford F250 SD with the 5.4 v8. I noticed my truck is missing at aprox 50mph when the truck goes into OD and revving at aprox 1500 rpms. I Changed my spark plugs and cylinder no 6 was fouled. The coil was cracked where the sensor connects to the coil. I used some JB weld to try and repair the crack. My truck is still missing and vibrating at 1500rpms at 50mph. I wonder if I need to replace the cracked coil? my check engine light is not on, but that means nothing.
Also, cylinder no2, I was not able to remove the coil. The bolt is stripped. I just got this truck a few months ago and the previous owner or last person who worked on this truck left me with a stripped coil bolt. Anyway, how do I get this bolt out? I'm afraid to crack the plastic area the retainer bolt threads in to...which is also plastic. I"m not too fond of my ford, at least working on it.
Ford Super Duty (1999-2016) :: 2003 2WD F250 Coil Spring Retaining Bolt Won't Budge
So I went to install a front end leveling kit in my 2003 2WD F250, looked like a simple task, except the bolt that holds the lower coil spring mount won't budge! I tried heating the nut, I soaked it with WD-40, tried a 200lb impact and a 30" breaker bar with all my weight. Is there something I am missing?
View 5 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Driver Side Rear Sway Bar Link Upper Bolt Removal
I have a 2004 F250 Lariat Crew Cab FX4 6-3/4' bed.
What is the procedure to remove the Driver's side Rear Sway Bar Link upper bolt? - the link attaches to the frame. The nut is on the inside of the frame with about 1/3" to 2/3" clearance between the frame and the fuel tank. Of course, the frame's "C" shape faces towards the inside.
Ford Super Duty (1999-2016) :: Stripped HPOP Fill Plug
I have stripped my HPOP fill plug. Any experience on getting one out? And a part # for a new one?
View 10 RepliesFord Super Duty (1999-2016) :: 2006 - How To Tighten Front Axle
It's the Right Front Axle Shaft on my 2006 F250 where it goes into the Hub/Bearing assembly.
Seems way to loose to me but after I removed the Lock-Out, I discovered the Axle Shaft is held in by a Snap-Ring not a Nut (WTF) so how do I get this tightened up
Also it's my understanding (I didn't remove) between the Axle & Steering Knuckle there's a rubber O-Ring. Could all this play be from that O-Ring being wasted Although that doesn't seem likely to me, Iam worried what's wrong
Ford Super Duty (1999-2016) :: How To Tighten The Nut On Lower Ball Joint
I have replaced my ball joints and now putting everything back together. I am having trouble tightening the nut on the lower ball joint, the joint turns with the nut as soon as it starts to get tight.
View 2 RepliesFord Exhaust :: 1989 F250 - Stripped Bolt Removal?
Ive got a 89 Ford F250 four wheel drive with a 460. Ive had an exhaust leak coming from the driver side, i already installed new manifold gaskets but just the driver side i could still hear a leak but on one of the exhaust ports towards the front there's a stripped bolt, is there any kind of tool of some sort were i can extract that. i barely have room with the power steering hose and steering shaft in the way.
View 3 RepliesFord Super Duty (1999-2016) :: 2005 F250 4wd - Clunk Under The Driver Seat
I have a 2005 f250 that has a wander and a clunk what feels like under the drivers seat. The driver side bushing in the radius arm has no dirt and looks like wear on it compared to the passenger side which is completely covered in dirt. My question is, bushing wear out will cause wander and a clunk. Is it hard to replace?
View 3 RepliesFord Super Duty (1999-2016) :: 2006 F250 - Front Seat Swap
After a 7 year love affair with our 2005 6.0L Excursion, we bought another 6.0L today - a 2006 F250 Crew Cab. It came with front buckets/console, and the used car lot (all diesel trucks...) was nice enough to let us swap the seats out with another 2006 F250 Crew Cab on the lot that had the front captains' chairs with the center seat.
Their upholstery guy did the work with the captains' chairs, but for liability reasons they wouldn't bolt the jumpseat in, since the truck we bought didn't have the studs in place. So, they sent it home with us and we're faced with putting it in. No problem, right?
Well... we found the place for the bolts to go, and thought we were home free. BUT... (see photo) - what have we done wrong?? The first photo (driver's side bolt of center seat) is fine, but the passenger side bolt hole is too close to where the front passenger seat needs to bolt in.
Ford Super Duty (1999-2016) :: 2012 F250 - Rear Seat Removal?
I would like information how to remove the rear seat back on a 2012 F250. I want to remove the head rests and from what I can find out they are bolted solid to the rear panel. I asked the same question earlier and got a reply for 2011, would that be the same? Is there any place I could get a schematic, a picture is worth a thousand words.
View 5 RepliesFord Super Duty (1999-2016) :: 2003 F250 - Front Seat Repair?
2003 F250 super cab, 335,000 miles. the seats are all in good condition except the drivers seat bottom, no rips or tears but the outer bolster area is worn. Looked at new replacement and no go. Is there a decent cover or a aftermarket replacement that looks good? The truck is not worth high end stuff, just would like it too look better
View 10 RepliesFord Super Duty (1999-2016) :: 2014 F250 - Rear Seat Back Removal?
I've got a 2014 f250 xl super cab and can't for the life of me figure out how to remove the back seat back.
View 2 RepliesFord Super Duty (1999-2016) :: 2005 F250 - Seat Belt Won't Allow To Move Forward?
I have a 2005 F250 King Ranch 4X4 Diesel and now experiencing an issue with the front seat belts
The problem is while being worn sometimes they will not let you lean forward- they act like you have a foot on the brake pedal and are locked-you have to lean back and forth several times to get them to let out if reaching for something on the dash etc..
I have searched the forum and found many issues where the seat belts stopped retracting- but my issue seems to be unique in that the seat belt will at times 'Not Let Out" when you lean forward.
Ford Super Duty (1999-2016) :: 2001 F250 - Seat Belt Buckle Randomly Releases
2001 F250. My drivers side seat belt buckle randomly releases and it's getting worse. Any sources on a new one or used even. Also, what other vehicles may have the same part number if I go used.
View 10 RepliesFord Super Duty (1999-2016) :: 2013 F250 - Driver Power Seat Stopped Working
I'm hoping this might be a "quick fix". Got in the truck the other day and my power driver's seat had no function what so ever. Not a big deal for me as I drive with the seat all the way back but the complaints are starting from my wife so it's time to find a fix.
This is the first F250 I've had so the wiring is a little new to me. I checked the fuse panel and the fuse seemed okay I swapped #9 out for #22 as they are both 30A and I don't need the trailer at this time but still no luck.
Are there any other systems tied into the driver's power seat, any wiring harnesses I should check or perhaps a fuse that is not shown in the owner's manual? My truck is the 2013 Gas F250.
Ford Super Duty (1999-2016) :: 2000 F450 - Rear Axle Assembly - Hub Retainer Threads On Housing Are Stripped
I have a 2000 F450, 7.3, 4x4, dually, VIN 1FDXF47F0YEA44380, with 30k miles, That needs a new rear axle - hub retainer threads on axle housing are stripped (nut welded on by previous owner). This axle is a case ID F81A-4001-BK, 4.88 ratio, 11.25 ring gear, with a 41.5" spring center. I have heard that the '99-'02 axles had issues until Ford switched over to the later square housed axles in 2002 or 2003 (Dana 110, I think). Is it possible to adapt these later (2002- 2004) axles onto a 2000 F450? And if so, what would be involved?
View 3 RepliesFord Super Duty (1999-2016) :: F250 - Changed Mounting Frame - Passenger Side Seat Fit On Driver Side?
On the F250 trucks, if I changed the mounting frame under the seat, will the passenger side seat fit on the drivers side? Basically, can I turn a passenger seat into a drivers seat?
View 4 RepliesFord Super Duty (1999-2016) :: Gasket Falling Apart - Bed Bolt Replacement?
I noticed a thumping sound in the truck bed when I'm driving and took a look underneath. The rubber gaskets for the truck bolt are all rotted and falling apart. Does it have to be replaced?
View 5 RepliesFord Super Duty (1999-2016) :: Triton Engine Bolt Pattern
Need to know if the 5.4 and 6.8 use the same bell housing pattern?
View 5 Replies