Ford Super Duty (1999-2016) :: While Connecting Battery Fuse Blown - Dead Ignition?
Did the blue spring upgrade today. The driver side battery was disconnected for 2 hours. After finishing the upgrade I reconnected the battery. When I touched the positive cable to the battery I heard a fuse blow. Now I have no lights, chimes, instruments, gauges, NOTHING, everything is dead. Cannot find any fuse blown. Is there a master fuse?
View 1 RepliesFord Super Duty (1999-2016) :: 4x4 Light Goes On After Replacement Of Blown Fuse?
I noticed I was not shifting into 4x4 electronically and replaced the blown fuse in the engine compartment. Now the 4x4 light goes on, but I don't think it is engaging the system...
The back end breaks free very easily, but there seems to be a little pull in the front. Is it possible to have unequal power to the wheels?
Ford Super Duty (1999-2016) :: 2000 F250 - Horn Stays On / Fuse Blown
Horn isn't working found fuse blown. Replaced fuse and horn stays on. Swapped relays still stays on. With fuse out pressing left side of horn cover on steering wheel I can feel/hear relay click. Pressing right side not so much. What and where to check? Is there a way to disconnect the horn buttons on the steering wheel?
View 1 RepliesFord Super Duty (1999-2016) :: Replacing Glow Plug - Dead Completely After Noise From Fuse Box?
i was replacing my glow plug relay and my ratchet hit one of the small wires and sparked. i went in the truck and I heard a really fast clicking noise at the fuse box. I opened it up a very top small relay was the one clicking. i replaced it and it still clicks. the truck is TOTALLY DEAD no power to anything. I checked ALL the fuses under dash and under the hood, they are all good. both batts are at 12. 9 volts. what would kill the whole truck like this. is there a main fuse somewhere? I really need to get this going tonight. it's gonna rain all day tomorrow and this is my only Tow Truck for my business.
View 14 RepliesFord F-150 - 1997-2003 :: OBD2 Port Stopped Working - Fuse Not Blown
My 03 5.4 the obd2 port isnt working i have tried 4 bluetooth adapters and a snap on scanner and nothing will connect to the ecm. im having problems and trying to read codes my check engine light isnt on but that don't mean anything. my truck is running really rich and blows a little bit black smoke when i rev it up after its been idling a few min and getting horrible gas mileage again. yesterday i went to start it and i had to crank on it 4 time before it finally started and then when i reved it up it almost died on the way back down but it caught itself. then today i go out and it starts right up and runs fine but its still running rich but i still cant get an obd2 adapter to connect to the ecm. I checked the fuse and its not blown my cigarette plug and the power port both work. i really dont know where to start in trying to figure out this problem. Right now iI don't really want to take it to a shop right now.
View 4 RepliesFord Super Duty (1999-2016) :: No Power To OBD Port
I posted this in the 6.0 section, but I thought maybe it should have been here since it's not really about the engine.
I bought a Kiwi2 BT OBD adapter and the Torque Pro app. Adapter does not power up when connected, key on or off.
Checked fuse #12 visually, looked good.
Verified power to booth the lighter plug and 12v accessory outlet.
Verified that the fuse I was pulling killed to lighter plug when I removed it.
I have not actually put a meter on the OBD pin because I am at work and have no meter. I did, however, connect the adapter to a co-worker's Tacoma and it powered up and I was able to pair it with my phone.
Ford Super Duty (1999-2016) :: OBD11 Port Location?
As luck would have it I'm leaving out in the morn for 600 miles , Noticed a nail in my L/F tire yesterday went too Goodyear they pilled the tire patched it inside.. Then this morn went to fuel up my ABS light stayed on .. Did this last yr. went off after a few days but since the tire was pulled maybe its a bad connection ??? ..Jut want to be sure and scan codes
I want to scan it now to check and reset any codes But looked under the Drivers side dash can not find the OBD connection port looked on Passenger side nothing there either.. Looked under hood around fuse box did not see anything that kind of looked like a port with a cap I'd assume they cap them if under the hood .. Its a 05 S/D 6.0 locate this OBD11 port
Ford Super Duty (1999-2016) :: 2003 - Error Code From Obd Port?
So I just bought a 2003 f250 v10 and I've plugged in my code reader and it couldn't get any info, so I took it to auto zone and they got an error code. I took a test lite to each little connection on the port with the ignition on and only got power to some of the metal connections on the port. So I'm wondering if all the little connections should have power? If so where should I start to look to find the problem?
View 5 RepliesFord Super Duty (1999-2016) :: 2003 F250 - No Power To OBD-II Port?
I have a 03 F-250, 5,4L / AT trans, FX4 4X4 with power Windows/Locks/ Mirrors. I recently had a problem with my windows and radio wouldn't work. When I would start the truck the windows wouldn't move and the radio wouldn't work. (Noticed the clock wouldn't even light up indicating no power). I was reading on here about the battery saver relay could be the problem and found out it was, so that is fixed. However, before I found this website I went to hook up my truck to my code reader/ diagnostic computer and it gave me the error code of no power from the OBD-II port. I made sure everything was fine on the code readers side by using on a different vehicle. I recently installed a trailer brake controller but that uses a cable/plug under the center of the dash.
View 2 RepliesFord Super Duty (1999-2016) :: Transmission Temperature Sender Test Port Leaking
So I had an issue with the trans temp sender leaking out of the test port where it's installed. My first clue was a smell of ATF, then a high trans temp, and finally many, many spots on the driveway. Anyway, I discovered that either I lost the o-ring for the sender or it didn't come with one. Regardless, I got an o-ring and its sealed for the most part. There is still a drop or two under the truck after it has been running. How can I fully get rid of this issue? Would some RTV thread sealer do the trick?
View 3 RepliesFord 6.0L Power Stroke Diesel :: Blown Fuse Causing Lack Of Power To OBD Port?
Blown fuse causing a lack of power to the OBD port?
I just got my Kiwi2 BT OBD2 adapter and was hoping to start diagnosing my truck, but the adapter won't power on while connected to the truck.
I pulled and visually inspected fuse #12, I also verified power to the cigarette lighter plug and the accessory 12v power outlet.
The adapter powered up with no problem when I connected to a co-worker's Tacoma.
Ford Super Duty (1999-2016) :: 2005 F350 - Melted Air Intake Manifold Port - Code P0171 And P0174
Wife took truck out and turned around after going less then a mile, saying it was running very bad. We got this truck about two months ago at a state vehicle auction. It was a state used truck, 145,000 miles, 05 Ford F350, ext cab and 8' bed. Anyway at first I thought it was valve tap until research said an exhaust manifold. With a fog machine in rear exhaust pipe we confirmed it was leaking and replaced the exhaust manifold. Figured it was probably a good time to replace spark plugs too. Took truck for a ride and she still buck and farted.
Got a code machine and got P0171 and P0174. Couldn't find a vacuum leak, but your could hear the air being sucked in. went to local parts store, guys couldn't find leak, but they said truck sounded like a steam machine. today I made a homemade smoke machine and smoke came from air intake, figured the gaskets were bad. The pictures show what I saw when I took the gaskets off. The port that has melted is the same port were the exhaust manifold was leaking from. Am in deep "doo-doo". What caused this?
Ford Super Duty (1999-2016) :: 2001 V10 - Blown Head Gasket?
Back Story: Ok so in my infinite wisdom I let myself get distracted when I was looking at an 01 F250 V10 Crew Cab. I thought, it needed all new breaks/rotor & 2 calipers. And new carpet and seats, then I would have a good hunting rig.
So I went and looked at the truck in the dark (first mistake). The guy was very honest with me and told me about all the body and interior issues. Even informed me of the caliper that he disconnected because he could not afford to fix it. He informed me that it did burn a little oil and it's been a while since he checked the oil. Well at that point I was going to look under the oil cap to check for any milky residue. Well I got distracted (Second Mistake).
So here we are 2 weeks after getting bringing the truck home. I already replaced the carpet and seats, breaks & rotor & 2 calipers. Well today I decided to go get some new oil and a filter, and do a quick oil change since who knows when it was done last.
Issue:While draining the Oil it seemed like there was an abnormally large amount of oil in this engine. (See photo of bucket full of oil from this rig.) Well didn't think much of it and swapped the filter. And went to add new oil to the engine and found that under the cap was some milky substance.
The V10 has 420K original miles. I have heard that is no big for the V10 but thought it would be good to note this detail. Questions I have: Should I get some kind of test kit to confirm it's a blown head gasket? If so what kind of Kit should I look for? Do you think this truck is worth replacing the head gasket?
Any chance this may just be a known issue for the V10 and I just need to replace some kind of valve? I could not find any you tube videos of a head gasket replacement on a V10 any thoughts where I should look?
My Skills: Just to be clear I don't know anything about the V10 motor. I have a 94 f-250 but have never had to dive in to a head gasket replacement before. I have done a head gasket replacement on smaller engines (IE: car and a jeep) but those were obvious that they had a bad head gasket.
Ford Super Duty (1999-2016) :: 2002 - Blown Out Tires Thrice?
Three times I've had a blown out tire on my '02 F350 crew cab/long bed 4x4 V10 while driving long distances on the freeway. Twice drivers rear, once drivers front.
All 3 times were in warm weather (85-95F). First time (rear) was on the Yokahama's which were on the truck when I bought it and a bit oversized. The date code says they were 10 years old, so I replaced all the tires with OEM sized BFG Rugged Terrains. Then it happened again- front last October. Did about $4K worth of damage. Now my buddy, called me up saying it happened to him (rear) while he was borrowing my truck for a trip.
In the first first two cases, I noticed a wobble. The second time wasn't as bad and stopped when slowed down (75 to 65mph), but it still blew. I specifically mentioned this to my friend to be on the look out and he said it never wobbled, but prior to it blowing the truck started to pull to the left.
In all three cases, the truck wasn't towing anything, but had stuff in the bed. The first two times I was taking my race motorcycle to the track, so probably had about 800lbs worth of gear in the bed & cab. My buddy was probably carrying less weight, but I'm not exactly sure how much. Before my buddy borrowed the truck I set the tires to 70PSI since he was going to drive 400mi down to Barstow and then some light offroading on BLM land.
The alignment was done after October and it has four new shocks. Tires look great, have maybe 15K miles and I rotate them every 5K miles. The only mods to the truck are swapping the 4" F350 rear axle blocks with the 2" F250 to lower the bed.
Ford Super Duty (1999-2016) :: Blown Fuses / Won't Shift Out Of Park
I did a bad thing last night, I put a jumper in the 20 amp cigar/data link connector and all kinds of things went out, will not shift out of park, no directional, power windows, power mirrors, no brake lights ,no hazards, no wipers, no interior lights and I don't know what ever else is not working.
View 3 RepliesFord Super Duty (1999-2016) :: 2005 F350 - Head Gasket Is Blown
2005 FORD F350 Lariat 6.0, 61,000 miles, and in prestine condition. Just got the news the head gasket is blown! HOW DID THIS HAPPEN?!!! My mechanic says to scrap the whole engine because the 6.0 is the worst engine around. This truck should last for years!!!!!
View 14 RepliesFord Super Duty (1999-2016) :: 1997 F250 XLT Spark Plug Chamber 2 Blown Out
The spark plug in chamber 2 blew off while the vehicle was in motion (approx 35 mph). Purchased replacement plugs and when I went to install, there was nothing for the plug to grab (i.e. appears that all of the threads on the block/casing are gone . Not sure what my options are.
View 2 RepliesFord Super Duty (1999-2016) :: Fuse 45 - Keeps Blowing Out?
My problem had been intermittent for last few days. I have a Ford Crew Cab - 7.3 Powerstroke Diesel. The ford store told me it would cost hundreds of dollars to chase this short- to wait til it finally burns out then - bring truck to them.?
My fuse # 45 a 10 AMP fuse . Keeps blowing out. This fuse controls the gauges on dashboard and fuel peddle. I can start engine and if gauges come up like they should- I can place into driver - and give engine fuel from peddle- gauges down dead and no fuel go to motor. It just idles and still runs and will still move forward or backward. But only at idle speed.
I could replace blown fuse - #45 - 10 amp and it would a the first few times would go and work normally.
Now everytime I replace fuse it blows fuse - sometimes after putting 10 or more fuses in- one might work until I stop or put into park. Then fuse blows again??
Last night and today it took no less than 20 - 10amp fuses to get close to home and end up straight wiring with a small piece of electrical wire - severing as a jumper- it ran great - til I stop at mail box and got mail - saw slight smoke and pulled wire quickly out and idled down driveway to house..
Ford Super Duty (1999-2016) :: Instrument Cluster Went Dead?
So, on my drive home from the pub tonight, my clusters went dead, then came back on, then died again. This behavior repeated for the 5 mile drive home. In addition, I believe the lights weren't working as well. The engine was still running, so I simply continued on home and parked for the night. The only thing I can think of might be the problem is the fact that I replaced the serpentine belt the day before yesterday. Is it possible that the alternator is not charging the battery properly and that is what my problem is?
View 14 Replies