Ford Super Duty (1999-2016) :: 2006 F250 - Rear View Mirror Fell Off
I have a 2006 F250 and the other morning I came out and found the rear view mirror laying on the cab floor. No biggie, I'll just glue it back on. Then I noticed the small black decal looking thing on the inside of the windshield. My question is, does this have to come off in order to re-install the mirror with standard Permatex mirror adhesive, or do I just put adhesive on top of it? Also, is there a different, specific adhesive used here that won't crack the windshield 2 weeks from now, like I read. Took a closer look and realized they used a thin adhesive patch to attach the mirror. I'll get one from the dealer.
View 3 RepliesFord Super Duty (1999-2016) :: Electric Cord Running To Rear View Mirror?
Why there is an electric cord running to my rear view mirror?
View 5 RepliesFord Super Duty (1999-2016) :: Backup Camera Only Shows In Rear View Mirror And Not In Nav Screen
I bought a 2011 F250 with nav and backup camera. the backup camera only shows in the rear view mirror and NOT in the nav screen. How to program it to show in the nav screen also?
View 7 RepliesFord Super Duty (1999-2016) :: 2015 - Up Fitter Switch Cluster Removal?
Does the switch cluster for the upfitter switches pry out? from the top, bottom? do you need to access from the side? Pictures welcome
I also have the brake controller installed
Phaeton :: RHS Rear View Mirror Removal?
I need to remove the passenger side rear view mirror. To do so, according to the workshop manual, I will have to remove the interior door panel first. Is that right or are there any shortcuts?
View 2 RepliesAccent MC (2006-11) :: Rear View Mirror Removal?
How to remove the rear view mirror? I've tried pulling, turning and twisting without any success. I have become spoiled by the self dimming mirrors in my other rides and want to add one with the Home Link buttons.
View 6 RepliesFord Super Duty (1999-2016) :: 2012 F250 - Rear View Camera Activation Wire?
I'm putting a new double din stereo w/ backup camera in my truck, I have everything wired except the violet/white wire (from the stereo) that needs to be hooked to a wire (on the truck) that will activate the camera when you put it in reverse. I cannot figure where this wire is on the 2012 for the life of me.
View 3 RepliesSonata I45 (LF 2015+) :: Rear View Mirror Tilt Down Too Much?
Adjusting rear view mirror? When I adjust my seat to the right position, then my rear view mirror shows me my rear deck where sub woofer located. I adjust the seat down and forward a bit and I can see about 70% of the rear glass. I have already raised my rear view mirror all the up.
View 11 RepliesFord Super Duty (1999-2016) :: Rear Fender Flares Removal?
I want to get the rear fender flares on my dually painted, they had a few scuffs when I bought it & I will soon have some spare time to get it sorted. We can't get the truck in the paint booth so taking them off seems like the ideal solution. I have had a quick look & I think it's just a case of removing the plastic liner (screws & clips) then it looks like there are some nuts up inside the steel fender, disconnect the wiring & they should come off!
View 2 RepliesFord Super Duty (1999-2016) :: F350 - Rear Head Rest Removal?
I have a 2016 F350 super cab and I can't figure out how to remove the rear head rest. Short of taking out my sawsall and cutting them off. How to get them off...
View 12 RepliesFord Super Duty (1999-2016) :: 2011 F350 - Rear Stabilizer Bar Removal?
I have a 2011 F350 with camper package (didn't want it). When I drive on a bumpy road (without 5th wheel), the truck suspension does not absorb the shock. The ruts just throws the truck side to side. Really hard, so I can't go on a dirt, rough road. On one bump it poped off my rear tire cap.
My problem may be with the camper package trying to keep the truck from going back and forth.
There is a 7/16 inch steal rod going from the truck bed, around the differential, and back up to the other side of the truck. Is that the rear stablizer rod?? Can I disconnect it? What would be
Ford Super Duty (1999-2016) :: 2012 F250 - Rear Blocks Removal
I want to know if there are any issues when removing the rear block, also do I have to put a new block in or can I just leave it out ....
View 12 RepliesFord Super Duty (1999-2016) :: 2012 F250 - Rear Seat Removal?
I would like information how to remove the rear seat back on a 2012 F250. I want to remove the head rests and from what I can find out they are bolted solid to the rear panel. I asked the same question earlier and got a reply for 2011, would that be the same? Is there any place I could get a schematic, a picture is worth a thousand words.
View 5 RepliesFord Super Duty (1999-2016) :: 2014 F250 - Rear Seat Back Removal?
I've got a 2014 f250 xl super cab and can't for the life of me figure out how to remove the back seat back.
View 2 RepliesFord Super Duty (1999-2016) :: Visor Mirror And Rear Map Lights Not Working - Code P1260?
So my driver side map light went out, went and replace the lamp. Now I can't turn on the map light when I depress the lens on both front map lights. Both rear map lights don't work either when I flip the switch and the driver or passenger visor mirror doesn't turn on when I flip the mirror cover. Maps lights do come on when I open doors. Also my Home Link (garage door opener now doesn't work). It's throwing a P1260 code (Theft detected vehicle immobilized). Do this might be related to my light issue? Is there a fuse on relay that controls this that might be bad or something needs to be reset? I've looked at the fuses by the passenger floorboard and every thing looks good. Why this is happening?
View 1 RepliesFord Super Duty (1999-2016) :: 2015 - Alignment Of Front Spline On Rear Driveshaft?
Proper alignment and re-installation of the front spline on the rear driveshaft of my 2015 F350.
I removed my rear driveshaft recently (it slipped right out upon removal without any force or resistance), and I'm getting ready to re-install it again this weekend, but I've noticed that one of the grooves between the array of male splines on the shaft itself appears to be slightly different than the rest - it seems to be slightly wider. It even has a white-colored stripe of paint down the full length of the groove as if it were denoting it as being somehow different from the rest?
Problem is, when visually inspecting the splines on the inside of the receiving yoke (the part that the spline fits into), I do NOT see any such differences. In other words, it doesn't appear that there is only ONE way to properly insert the front splined-end of the driveshaft. What am I missing here?
Is the front splined-end of the rear driveshaft intended to be inserted into the yoke in ANY position around the dial? Or is there only ONE specific position or orientation that it is intended to be inserted or installed? NOTE: I've seen references elsewhere on-line that seem to indicate the need for proper alignment when there are multiple U-Joints, and maybe this is a part of it (?), but I'm not quite sure which U-Joints to consider or how to interpret such an "alignment".
Ford Super Duty (1999-2016) :: 2015 F250 - Rear Wiring Harness Connectors?
I'm trying to find out what the two connectors in the image are.. I've looked through the manual that I have and searched around on the web and find nothing.
They're on a 2015 F250. "upfitter" switches were installed from the factory.
Ford Super Duty (1999-2016) :: 2004 F250 - Driver Side Rear Sway Bar Link Upper Bolt Removal
I have a 2004 F250 Lariat Crew Cab FX4 6-3/4' bed.
What is the procedure to remove the Driver's side Rear Sway Bar Link upper bolt? - the link attaches to the frame. The nut is on the inside of the frame with about 1/3" to 2/3" clearance between the frame and the fuel tank. Of course, the frame's "C" shape faces towards the inside.
Ford Super Duty (1999-2016) :: 2015 F350 - Rear Axle Pinion Seal Leak
I was looking underneath the truck yesterday and saw that the rear end pinion seal was leaking. Looked like it had been for a while. Truck has 35,850 miles on it. Unscrewed the fill plug and a lot of pressure is released. So I'm assuming the breather is clogged somewhere along the line. I have an appointment at the dealer on Friday to see whats wrong. What is supposed to be at the end of the breather tube? Mine has a barbed 45ish degree fitting on the end of it. Its a SRW by the way.
View 5 Replies