Ford Super Duty (1999-2016) :: 2002 F250 5.4 - Valve Cover Leaking - Gasket Replacement?
I have a 2002 F250 5.4with Air Conditioning. The valve covers are leaking and the gaskets need to be replaced. I am attempting the valve cover gaskets. I was able to get the drivers side cover off with some difficulty. For the passenger side valve cover. There is very little " no" room to get at the bolts. I read somewhere that I may have to drop the engine on that side. I will do that if I have to.
View 5 RepliesFord Super Duty (1999-2016) :: 2001 7.3 Won't Start After Replacing Valve Cover Gaskets - Code P1316
Ok I have a p1316 code so I was told to change valve cover gaskets so I did. Now starts for 4 sec and dies, what is going on....
View 2 RepliesFord Super Duty (1999-2016) :: 2001 F250 - Overheating - Replacing Bypass Valve On Trans?
I am having some trouble with my 4R100 overheating.
Truck is a 2001 F250 XLT 7.3L with 244k miles on it. According to previous owner, the transmission was replaced around 185/190k but there was no paperwork to prove it.
I recently had a leak from one of transmission lines coming into the bottom of the radiator (the one on the passenger side). I replaced it and topped off the little bit of fluid that leaked out. Last weekend I installed a temp sensor in the transmission and hooked it up to my pillar gauges. The first few days driving with it, the temp was at/around 180 degrees, 25-30 degree outside air, unloaded on the highway averaging 70-75mph.
Today on the way home, the temp got to 180 after 35-40min of driving then continue climbing. I pulled off the highway after 1.5hrs and the temp was almost at 210 degrees. I let it idle for 5-10min and the temp didn't change. I turned it off and let it sit for 15 min. Upon starting it back up, the temp had dropped to 180. I continued driving and the temp climbed back up to 210 within 35 minutes. (65-75mph, 24 degree outside temp, unloaded). Once off the highway I averaged 35-45mph on the back roads to my house. The temp started to drop back towards 180 degrees.
Before I start throwing money at it, and installing a 6.0 cooler etc. I am thinking there is something else wrong here. I am going to look at new lines and replacing/repairing the bypass valve on the transmission. I am driving 2hrs to work each way and thats when the temp really starts to go up. The fluid doesnt smell burnt, its still nice and red. I am going to try and flush the lines this weekend and see if something is plugged/caught. I ordered an inline filter today and will put that in with a new hose from the transmission to the radiator (old one is rusted).
Ford Super Duty (1999-2016) :: 2003 F250 V10 - Inconsistent Tapping Coming From Passenger Side Valve Cover
I just bought myself a 2003 F250 XLT with the V10 in it. Low miles, not beat, 6 speed, very happy with it. I noticed today that there was an inconsistent tapping coming from the passenger side valve cover. I searched online and was pointed towards the PCV baffle. I pulled the breather hose off and stuck my finger in the hole, and the baffle is indeed detached. Now I know that I need to pull the valve cover now to at least remove the baffle; is there anyway to reattach the baffle, or do I need to buy a new valve cover?
View 8 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Replace The Intake Manifold Gasket?
I needed to replace the intake manifold gasket on my 2002 f250 v10. Tore everything apart put the new gasket in which was the same as the old one lyrics to notice something isn't right. I have been driving the truck for over 10 years like this. Is it OK to just continue bolting everything down and go on like this? I am guessing the prior owner 10 plus years ago put the wrong intake on. I keep looking up intakes but they all look just like the one I have. Also that port exposed is on the back passenger side.
View 3 RepliesSonata NF (2006-10) :: Replacing Valve Cover Gasket On 4 Cylinder 2.4L
Changing the valve cover gasket on the 4 cylinder 2.4l. I was going to change mine's. Didn't know if there are any special tips like sealant to be used, loosening bolt sequence or tightening sequence, torque values.
View 9 RepliesHonda - Accord :: 1994 - Replacing Valve Cover Gasket?
I'm replacing the valve cover gasket on my 94 Honda Accord. I've heard all sorts of crazy opinions on what needs to be done while installing the gasket such as using various sealants or lubricants. Should anything be put on the gasket or should I just drop it in and screw the valve cover back on?
I'm also replacing the spark plugs while I'm at it. Is there anything else I should do while I'm in there?
Golf IV / Jetta IV :: Engine Won't Start After Replacing Valve Cover Gasket
My mk4 sat for a while and upon starting up was misfiring. I checked for pvc leaks and didn't see anything but went ahead and cleaned my maf sensor and decided to pull my coils. Cylinder 1 had oil on the tip and around the spark plug which to me spelled out a bad valve cover gasket. I got all the parts to do the inner and outer gaskets and replace the coil and spark plug, however we got a snowstorm and my luck a rabbit got in and ate the wiring on one of my fuel injector connectors.
So went ahead and put on the new gasket, replaced the coil and plug and bought a new Fuel Injector Connector and spliced in onto the Injector "Pigtail'. I double checked everything was reattached properly and let the gasket sealant dry for 24 hours. I went to start it tonight and after trying to turnover it completely cuts out, wont even start up. I'm extremely frustrated at this point and am thinking the rabbit must have gotten to something else unless I did something wrong in the process of repairing.
Ford Super Duty (1999-2016) :: 2000 F350 - Leaking Oil From A Bolt On Passenger Side Valve Cover
My 2000 f350 is leaking oil from a bolt on the passengers side valve cover. it is one of the bolts on top of the valve cover. Can I just remove the bolt and put a rubber washer under it or do I need a new valve cover?
View 2 RepliesFord Super Duty (1999-2016) :: Loud Knocking Noise Coming From Left Valve Cover Area Occasionally
I just picked up a 2001 F350 with the 5.4L with 200k miles. When I test drove the thing the engine sounded fine. I got it home and noticed that it occasionally has a loud knocking noise that is coming from the Left Valve cover area. It sounds like an old Chevy 6.5L Diesel ...
It comes and goes, Hot or Cold. It seems like it usually goes away when driving with RPMs above 1500 or so, however I took off with it yesterday and the noise would not go away, it seems like it might be low on power when the noise comes on, but then again it always feels low on power, so who knows.
I have changed the plugs, oil, and verified there are no exhaust leaks at the manifolds.
Here is a video of the noise: YouTube....
I dont think it is the timing chain, as it seems like its coming more from the center of the cover, when placing my hand on the cover near the timing set there is no vibration or anything that would lead me to believe its the chain.
All of my searching so far turns up 3V stuff, and little info on the 2V engines. The valve cover looks like a nightmare to get off, who have to work on these things (including me).
Ford Super Duty (1999-2016) :: F250 - Head Gasket Leak?
I've been trying to figure out what is going on with my '99 F-250 V10, you can check out this thread for the back story
[URL]....
I did a compression check and the results seem inconclusive to me- see image.
Before I did the compression check I started to take the intake manifold off to change the gasket set and it's about 50% done. I'm at a crossroad now. Do you think I should finish switching out the intake gaskets or do you think it's more than likely a head gasket? I would hate to put it back together, it still smoke and have to take the intake and everything else back off to do the head gaskets.
Someone had mentioned a possible small crack in the cylinder wall that is closing up when the engine gets heat in it and obviously doing the intake and cylinder head gaskets would fix it if that's the problem.
Ford Super Duty (1999-2016) :: 2002 - Oil Pan Gasket Leaking?
my oil pan gasket is leaking on my 2002 f350 5.4l 4x4. I have read lots of threads on replacing this gasket on an f150 but haven't seen one for an f250/350. so what is the procedure to do this job on an f350?
View 2 RepliesFord Super Duty (1999-2016) :: 2006 F250 - Head Gasket Replacement
I am replacing the head gaskets on a 2006 Ford F250 6.0 .... I have heard that I should replace the head bolts with studs. Do I torque the studs just like the bolts?
View 5 RepliesFord Super Duty (1999-2016) :: 2001 F250 - Replacing Headlights?
I just replaced the head lights on my 2001 f250 it had the sealed beam one-piece glass headlights and I replaced those with regular headlights and when I went to get bulbs I found out after I get home the connector is different from the new bulbs. the new bulbs fit correctly but I can not hook plug them the plug has 3 connectors that have two connectors level and one is higher than the other two and the new bulbs the three prongs are level.
My question is. is there another bulb that will fit and plugin and if so what is the part number? is there a adapter that I can get that will allow the factory plug to work? or will I need to cut the old plug off and splice a new connector on?
Ford Super Duty (1999-2016) :: F250 Won't Start Since Replacing ORing
My 1999 F250 won't start ever since I replaced the o ring where the dipstick meets the oil pan. Started it when I was finished it ran for a minute and shut off, the truck was on a slope my low fuel light was on. I have it sitting on the flat now but still not starting but turns over?
View 1 RepliesFord Super Duty (1999-2016) :: F250 - Replacing Brake Lines
I plan on replacing the brake lines on our 1999 Ford F-250 Super Duty. The rear line blew out right by the hose, on the framerail. All five lines, all five hoses. What size lines? Looks like front two are 3/16", rear two over the axle are 3/16", and the rear line in the frame is 1/4".
We are removing the bed (2013 bed) to make things easier. I am thinking fuel lines and parking brake cable while the bed is off. I have stainless steel hoses from KLM performance and I am also planning on replacing the rear rubber hoses. Obviously I'm using nickel copper line. There shouldn't even be an option for other brake line.
[URL].....
Ford Super Duty (1999-2016) :: F250 - Header Gasket Leak / Passenger Side Only
1999 f250 with some mild upgrades. Trucks got 189,000 miles. Stole it from an older guy for 4k. In fantastic shape. As the weather got colder I noticed an exhaust leak. Took it to a muffler shop only to find that it's got an aftermarket header on the passenger side only. Is that common to replace only one side?. the gasket has gone bad and needs replacement. I wanna replace both headers?
View 8 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Leak From Oil Pan Gasket And Coolant Lines
I have a leak from the oil pan gasket and oil coolant lines. From the research I have done, it looks like I have to lift the motor to change the oil pan gasket. Any way to get this done without lifting the motor??? 2000 f250 5.4 2wd....
View 4 RepliesFord Super Duty (1999-2016) :: 2005 F250 - PCV Valve Location
I have a 2005 f250 with a 5.4l 3v. Where the pcv valve is located is it in the valve cover or attached to the intake and what does it look like? I have pulled the hoses off both sides but I have not found it let.
View 3 Replies