Ford Super Duty (1999-2016) :: Airbag Light Came On Steady - No Blinks
2013 F250 6.2, 71500 miles. Airbag light comes on and stays on steadily, no blinks so that I can read the code. Any way before I make the dreaded trip to the dealer?
View 3 RepliesFord Super Duty (1999-2016) :: 2004 F250 V10 Battery Light Flickers
2004 F250 v10 xtl 260xxx. Started off by using my remote start, truck started up ran for about 5 sec then shut off, then restart itself and shut back off. When I manually started it, it ran fine. I noticed my battery light was on and as I was driving it would flicker. First thing I did when I got home was clean all my connections to see if that worked. Battery light still on, checked my volts on my battery and they were at about 11.8 with a slow but steady drop while truck was idling.then checked my alt, that too was at about 11.9 with a stead drop.
Alt was only about 7 months old and I had a warranty on it so I had it replaced at Napa and had them test it there. Good alt. Installed the new alt charged up my battery and turned it over. Battery light still on and flickering. Checked all my wires for corrosion, checked all my grounds. Everything checked out. Checked my battery again 12.4 with the truck off, cranked it over and it was back at 11.9 with a steady drop and almost the same reading with the alt. I replaced the battery as well yesterday, seeing how it was about 7 years old.
Ford Super Duty (1999-2016) :: 2004 F250 - Battery Light Came On Suddenly
I was driving and all of a sudden the radio died, battery light came on, Power windows and interior lights died, gauges died speedometer went all the way up to 100. The Head lights, turn signals and heater work. When I got home I opened the hood and the battery was boiling.
View 14 RepliesFord Super Duty (1999-2016) :: 4X4 2004 F250 - Dash Light Staying On
The light on dash for 4X4 stays on no mater where the switch is placed I have it in 2 wd and it stays on. Where I need to start looking.
View 4 RepliesFord Super Duty (1999-2016) :: 2004 F250 V10 - Stalling Out - OD Light Flashing
I have an 04 F250 4x4 king ranch with a 6.8 V10.
When I first bought this truck it had a problem of stalling out at stops. You could sometimes hold the brake and gas and push your way through it but it would sputter for a second and try to die and then it was fine once you got going. The OD light would flash, check engine light would come on and it would throw a P0720 code for the OSS. I did some researching and I pulled the sensor in the pumpkin before that because I read that could cause the same problem, so I cleaned it and put it back but it didn't solve the issue. Then found that an K&N air filter can often times clog the MAF and cause the issue so I pulled my air filter and sure enough it was a K&N, I swapped it with a normal filter and sprayed some MAF cleaner and its been running like a top for months... until now.
It started again, gradually at first. It would die when I started to back the truck at a very low speed to load my 4 wheeler. I fired it up and it was good again for a couple more weeks, then I went to hook to a horse trailer and I was having to back up a hill to get to it, and it just kept dying, OD light would flash, check engine light came on. I was in a bind so I just tried wiping off the MAF with a rag, that didn't work, my girlfriend was using the truck and said it kept dying whenever she stopped. I got it home and cleaned the MAF with cleaner really well but the problem persisted. I went ahead and changed my oil, spark plugs(gaped at .052-.054), replaced the IAC(which looked like it had been installed once before so I am guessing someone tried it and when it didn't fix the problem they returned it) and changed the fuel filter. I drove it around and it ran fine, drove it to work and it ran fine, my girlfriend took it for about 15 minutes to run an errand for me and it was fine until she got back in the parking lot and liked to never got it parked again it stalled so much.
So I went back to the drawing board and read that it is rarely the OSS that is the problem but that often times the issue is a bad coil pack. I don't have a scanner nor do I know how the heck to use one. I plan on going out of town at the end of the week and the truck has 194k miles on it so rather then take it to a shop and try to find out which COP was bad I just decided to replace all of them(I know, I know, you should never just start replacing parts). I only had time to replace 5 of them, I took the truck out and again it dove fine for an hour, went through traffic OK. It sat for an hour and when I left it started to die again, I could drop it in neutral and it would fire back up and as long as I gave it just a hair of throttle it stayed running fine, take my foot off the fuel and in a minute it would die again. After I drove for a bit it was fine again. Now I know the problem may yet be in the remaining 5 COP that I must change tonight but in case it is not I wanted to get input on this.
I've read the problem can come from a bad ground, so I took every ground point that I could find under the hood and I cleaned the connectors and took the paint off at the connection site just for good measure. The problem persists. I've read that sometimes a diode can go out on the alternator and cause this problem, I did use my amp meter and I'm checking out at 13 volts while running. I'm not the best with meters so I'm not sure how else to check the diode?
I've also read that taking it to a dealership is hit or miss for them diagnosing the problem, sometimes they find the issue, sometimes they just change the OSS. The only mechanic I trust closed his shop and is now service manager of the Dodge dealership. I'm thinking since this seems to be a common problem that maybe ford might have more knowledge of it then dodge but I trust the dodge dealership more because of who is over it. Either way I know it will sit in a dealership for awhile before it ever gets looked at and if they have to chase any electrical problems then that starts racking up $$ fast.
So what am I missing? I've thought about replacing the MAF since cleaning it the first time solved the problem. When it did this the first time I still had my 01 F250(it never gave me problems like this) and so I took the MAF off of it and swapped them and sure enough it fixed my problem so I switched them back after I cleaned the MAF and like I said it's been running fine until recently. I'd rather not throw money at this by replacing parts and hoping for the best. I've also read about tracing the harness that runs from the sensor on the pumpkin to the OSS and on. That harness runs through all kinds of stuff so I'm dreading that but it will also be a next step. I haven't pulled the OSS because its in a very awkward position on my truck.
Ford Super Duty (1999-2016) :: 2004 F250 - Transmission Light Started Blinking
Driving to work the other day my transmission shifted down and the transmission light started blinking. It felt like it geared down like it was in 4x4 I was doing about 55 at about 2600 RPMs. This has happened twice now and lasted around 2 minutes then stopped and ran great.
View 2 RepliesFord Super Duty (1999-2016) :: 2004 F250 - High Beam Indicator Light Very Dimly Lit
I was cruising my truck down the road and noticed that my high beam indicator light was very dimly lit. I wondered why this would all of the sudden come on at all if the high beams were not on so I pulled over and took a walk to the front of my truck to check my headlights. Sure enough the passenger light was very dim. (I must assume the high beam indicator light being dimly lit is also an indicator for headlight malfunction/burn out)
I figured out the plug has a keeper piece that is supposed to hold it in the bulb base but it was broken off and missing.
I went to the auto parts store to find some kind of fix. To my surprise they have a replacement plug for my truck. The down side is it costs $95 and it still had to be shipped! I decided I could figure something else out.
After I pulled the four 5.5 millimeter screws out of the headlight housing. I noticed there is enough room on either side of the light contacts to drill a hole thru the plug and the bulb to allow a pin to be placed thru both of them which would keep the plug and bulb socket from coming apart.
These are the pins or keepers I used.
A 1/16" drill bit did the job. I put the new bulb/socket and the plug together and drilled a hole on each side of the plug right thru the socket at the same time far enough back and at a width to avoid the contacts of the bulb socket and plug. (there is a rubber gasket in the plug that should be avoided but if you still knick it as I did you can fill the plug or the socket with dielectric grease that most car parts stores have and it will keep any moisture out but not effect the electrical current, do not use silicone, one day you will have to take it back apart for a bulb replacement or something.)
This is the bulb socket with the holes already drilled and the plug removed. This is what it looks like with the bulb/socket and the plug together and the keepers in place. And the back of the composite headlight housing with the assembly installed.
Make sure you install the bulb/socket and plug with keepers on the housing before you bolt the housing to the truck because there is not enough room to get your hands behind the housing to install the keepers with the housing bolted to the truck.
Since I replaced the stock bulb with a Sylvania Silver star I had to replace the driver side too so I didn't end up with a headlight being brighter or "whiter" than the other. Even though I was incredibly careful I still broke the plug on the driver side too! So now both of my headlights now have this mod on them.
Ford Super Duty (1999-2016) :: 2004 F250 - Check Gauge Light Comes On When Stopped Or Coming To A Stop
I have my 2004 f250 6.8L. Recently my truck has been having issue with the oil needle. When im stopped or coming to a stop my Check Gauge light comes on and my oil needle drops all the way down. As soon i step on gas it goes right back up. What could it be?
View 7 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Power Mirror And Turn Signal / Clearance Light
I did some reading on here this morning and ended up at 1A Auto looking for mirrors. I want to make sure I get the correct thing before ordering. I have a '04 250 with factory tow mirrors that are power mirror and turn signal/clearance light. I want to upgrade to the '08 style. Which of these would work? I would think either, but I'm not sure about the wiring harness?
Search Results for 1AMRP01095 - 1A Auto
2008-10 Ford Mirror Pair - 1AMRP01096 at 1A Auto.com
Ford Super Duty (1999-2016) :: 2004 F250 - Slight Hesitation When Trans Is Engaged And Tow Haul Light Blinks
I have a 2004 F250 Torqshift trans, 155,000 miles. It has had a slight hesitation when trans is engaged for about 4 years, not a problem the dealer has no fix they said.
Now today for the first time I had a tow haul light come on while driving on the freeway. It would not go into overdrive and the light keep blinking. Later in the day, I let it cool down and it drove fine to the store about 2 miles. When I got in to drive home it had tow haul light go blinking and check engine light came on this time.
I hooked up my code reader and it's giving codes: P0720, P0751 and P0766.
Should I take it to the Ford dealer, a Transmission shop or have a friend who worked at Ford Dealer do the Work? I see that some people have changed out the TFT sensor and corrected the problem. While the pan is down should I just have all the shift solenoid sensors changed?
Ford Super Duty (1999-2016) :: F250 - SES Light Came On
I've had my 99 F250 for about 2 weeks and my SES light came on last week. I took it into AutoZone and they read the code. DPFE sensor EGR etc. The kid behind the counter mentioned something about removing those and saving some money. We don't have any emissions testing. I don't want to take any short cuts really, but if its unnecessary to have than why not delete it. I have the 5.4 and it has 189,000 miles and we did buy the truck to haul the camper so that plays into the scenario also.
View 9 RepliesFord Super Duty (1999-2016) :: 2000 F250 - ABS Light Is On / Blinking Overdrive Light Comes On At Around 25 MPH
The problems that I am having at the moment are that the abs light is on from the speedometer, odometer, also the blinking overdrive light that comes on at around 25 mph. After some research I had purchased a ford factory sensor for the rear dif. I then replaced the old sensor with the factory one. Started the truck and not a single thing had changed, both the meters were not working as well as the od light was still flashing.
View 4 RepliesFord Super Duty (1999-2016) :: 2004 F250 V10 Not Going Into 4x4
Just wanting to know what might be wrong truck will not go into 4x4. All fuses in panel looked good. Light on dash is not coming on was working last weekend just fine. Have the hubs in lock position not auto.
View 6 RepliesFord Super Duty (1999-2016) :: F250 Won't Go In Any Gear - 4x4 Light On?
Kevin here, and I'm a newbie. I recently purchased my first 4x4, a 99 F250 with ESOF. Last night I had put it in 4high for a rough road turn-around and then flipped the switch back to 2H, the 4x4 light didn't go off. Then when I got to the house (about 1/2 mile), it rolled when put in park and now it won't go into any gear.
View 7 RepliesFord Super Duty (1999-2016) :: 2005 F250 - ABS Light On?
I have had the ABS light on for about a year now. I looked thru the forums and found that the typical reason if a faulty rear VSS (vehicle speed sensor). I found a replacement part online and got it ordered and replaced the original part. Simple 5 minute fix, but it didn't fix it!
Now when I get in and start the truck the ABS light is off, but after I drive off about 20 yards the light comes back on and stays on.
The other day someone stepped out in front of me at a cross walk and I hit the brakes pretty hard and although the truck stopped in time, the rear wheels locked up, so I'm thinking the issue is at the rear.
Ford Super Duty (1999-2016) :: 2001 F250 - ABS Light Is On And Overdrive Light On Shifter Is Flashing
I recentlyHad to replace the right front wheel bearing and after the install the speedometer and turn signals don't work, the ABS light is on and the overdrive light on the shifter is flashing. I've replaced the VSS on the rear diff, pulled and cleaned Speed sensors on front hub?
View 2 RepliesFord Super Duty (1999-2016) :: 2010 F250 XL - OEM Fog Light Install / Switch Didn't Light Up
I have a 2010 f250 XL v10 6 speed 4wd. I was looking into adding factory fog lights to it. I have the factory plug by the headlight. I've read that some XL trucks just need the fog lights, wiring harness for the lights and the headlight switch with the fog light option.
So today my buddy (has an 09 f250 xlt with factory fog lights) and I decided to try his headlight switch in my truck to see if it would send power to the plug by the headlight. Plugged it in, turned the fog lights on and had no power. Actually the little fog light light on the switch didn't light up that I noticed either. So we compared wiring harnesses going to the headlight switch. Both trucks have 9 wires. #21 fuse in the kick panel is intact and good.
What else my truck would need in order to use the factory fog light parts? I know I could run new wiring and use an aftermarket switch but I'd rather it be factory.
Ford Super Duty (1999-2016) :: 2004 F250 Running Low On Oil
I have a 04 f250 with aprox 95k on it 5.4L I knew I was over mileage for a due oil change I haven't been driving it much it crossed my mind, as I am usually very adamant about changing fluids. I went to check my oil and only a smudge of oil on the dip stick. I know this is not good but the truck runs fine, no noises, no knocking, not a chatter from the valve train. Oil pressure was good everything seemed fine did I get lucky? I know it wasn't good I am not going to let that happen again everyone think I dodged the bullet?
View 9 RepliesFord Super Duty (1999-2016) :: 2004 F250 - 4x4 Will Not Engage
I have a 04 ford f250 superduty... I tried to use my 4x4 today and the front wheels would not engage using the ESOF. The light comes on in the dash saying its in 4x4. i do not believe i have a vacuum leak because it doesn't switch over to the automatic setting for defrost. what else could it possibly be I'm stumped at this point.
View 14 Replies