Ford Super Duty (1999-2016) :: 2003 F350 - Gear Shifter Very Tight And Hard To Pull Down
I'm looking at purchasing a 2003 F-350 from a Ford Dealer, Drove the Vehicle last night and the Gear shiftier was very tight and hard to pull down. Is this a real concern? The Sales guys said its better to be stiff rather than sloppy. But they will say anything, right. The vehicle is a deal and so I'm looking to find out why.
View 1 RepliesFord Super Duty (1999-2016) :: 2003 F350 Pulling Hard Left At Low Speed When Braking
I have an 03 F350 4x4 dually. Was pulling hard left at low speed when braking (front). Replaced pads, calipers, rotors, hoses and tires. Still the same problem. You can feel the abs activate right before it almost locks up the left front brake (basically will pull the steering wheel out of my hand). BTW the abs light does not come on.
View 2 RepliesFord Super Duty (1999-2016) :: 2003 F350 - Hard Or No Start / Shaking In Low RPMs / Slow Response From Gas Pedal
I need fixing my 2003 f350 6.0 diesel, I have been working on this truck for a while and still am having problems, here was the original symptoms:
-Hard start or no start on a sunny day
-Rough idle for 10-15 minutes
-Rough shaking in the low RPMs (35 mph)[/COLOR]
-Slow response from the gas pedal
-boost would only get to 14
My dad and I then did many things to the truck in the shop, those things are:
-Air test and replacement of coupling going into oil branches (next to HPOP)
-Replaced EGR valve (no good)
-Replaced ICP sensor (leaking oil)
-Replaced ICP sensor and IPR valve piggtails (due to frayed wires)
-Cleaned Turbo
-Cut MAP sensor hose and reattached it (spliced on the end)
-New battery
-Performed a bubble test and found two bad injectors on passenger side (injectors #5 and #7)
-Cleaned and lubed tops of injectors
-Replaced O rings and copper crush washers on all injectors
-Replaced nipple cup O rings (tight)
-Blew out injector cups
-Bubble tested after injectors put back in (no more bubbles)
-New FICM, EGR cooler and oil cooler were already installed
-Ohm'd main engine wiring harness (good to go)
-Taped up frayed wires on fan clutch connection
-Increased wire gauge on the positive jumper between both batteries
-Sanded each ground on the batteries and engine, cleaned battery clamps, lithium greased connection points.
-Checked fuel for air (no air)
-Checked fuel psi (85 psi, plenty)
-Oil changed
After doing all of this (diagnosing as we fixed each thing) we now fixed many things including the hard/no start problem. Now, for the first three to five minutes:
-It starts right up
-Runs perfectly, no shake and instant response from the gas pedal and turbo
-Boost goes to 28
-ICP is 800-950 on idle
-IPR is 25-26.9% closed
After five minutes however:
-Starts to shake
-IPR % starts to raise
-Received no response from gas pedal (absolutely no power)
This truck has been torn apart like 8 times and I have to do it on my spare time.
Ford Super Duty (1999-2016) :: 2004 F350 - Loud Clunk Noise In Forward Or Reverse Hi Or Lo When Accelerate
Ive got a 04 f350 that after u shift into 4hi or 4lo when u accelerate it it makes loud clunk noise in fwd or reverse hi or lo. With hubs unlocked it still clunks. Have checked, wheel bearings, axle U-joints, and driveshaft joints all good. So I am thinking I've got issues in t-case. Popped drain plug out and wow that dex merc 4 looks nasty. So thinking I need exploded view of transfer case.
View 4 RepliesFord Super Duty (1999-2016) :: F350 7.3 Diesel / Hard Cold Start
i have a f350 superduty with a 7.3 turbo diesel and I pretty much hafta keep it plugged in to get it to start, i have installed all new glow plugs and both relays have been changed and the problem is still there, only other option i have not tried yet was changing the pcm controller but unsure if that is the problem ..
View 14 RepliesFord Super Duty (1999-2016) :: 2011 F350 - Transmission Shifting Hard From 3 To 4 Going Up And 2 To 1 Going Down
I have a 2011 F-350 6.2L that has extremely hard shifts from 3 to 4 going up and 2 to 1 going down. Sometimes on downshifts it feels like something has ran into the back of the truck. I had the computer updated when the truck had approximately 40,000 miles on it and he assisted a little bit. The truck now has 140,000 miles and it is back to shifting horribly. I put it in the shop at the dealer on 30 December 2013. The dealer says that the problem is that the shift solenoids need to be replaced but that they are not available. The truck is still sitting at the dealer and I am being told that the parts should be available mid February.
View 10 RepliesFord Super Duty (1999-2016) :: 2000 F350 7.3 2wd Dually - A/C On Hard Acceleration Only
I have a 2000 F350 7.3 2wd Dually - that only only produces cold air conditioing on hard acceleration only stays on for a few minutes then falls away.
The temperature is cold when its going. I've checked the levels and its gased OK. There is no voltage to the clutch on the compressor when it is not working. So I take it, that it isn't the clutch shim/spacing.
If I accelerate hard it comes back immediately. Whether I am going slow at 1500rpm or doing 70mph at 2500rpm - Uphill or downhill. Its seems to need a substantial amount of Turbo boost for just a few seconds to turn on.
I actually bled the system a little and its made it worse. Stays on for a shorter time and isn't as cold. However the low pressure side is still on the high side at 50psi when running.
Its done this for approx 2 years and its getting worse.. And now its really hot outside.
Ford Super Duty (1999-2016) :: 2001 F350 V10 - Hard To Find Gear
Got an '01 f350 v10, auto. When using steering column shifter tends to be hard to find reverse and drive. Is it something in steering column selector or is it in tranny? The truck has 40,000 miles on it. Have a parts truck also so just trying to figure out where to start first.
View 3 RepliesFord Super Duty (1999-2016) :: 2015 F350 Diesel - Hard 6 To 5 Downshift
2015 F-350 diesel purchased Sept 2104. When towing my 16,000 lb 5th wheel the 6 to 5 downshift seems to have gotten much harsher in the last few months. About 10,000 miles on the truck, much of it towing. Is this an indication of a developing problem?
View 1 RepliesFord Super Duty (1999-2016) :: New Long Block / Truck Still Smokes When Cranked
I have recently placed a new shortblock from Nashville engines. My retired ford diesel mechanic said it was the best shortblock he has ever seen. Since working on my truck he has ordered 6 small block from them. I used reman'd Ford heads after going through three sets of heads from Clearwater heads and one set from ProMaxx Cylinder Heads out of rainbow AL.
Since putting in new long block the truck smokes a puff of white smoke each morning. Enough smoke that it bothers me. A new longblock with new injectors should not be smoking. I have changed the fuel filters thinking the 5 sets of heads previously put on the truck may have gummed the motor up and have ran octane boost for the last 500 miles. I ran a 2000 mile road trip and the truck still smokes when cranked. sometimes a lot and sometimes a little. What could be causing this?
Ford Super Duty (1999-2016) :: 2006 F350 Shuts Down While Driving After Hard Acceleration
I have an 06' f350 6Ltr. Over 300 k. Good shape, i have owned it for about a year. My first diesel. Last week it wouldnt start, had a 1/4 tank. Read about problems with other trucks with a broken pick up on fuel pump. So i filled the tank and it started. Next morning used command start and it ran for 1 minute then shutdown. took about 5 minutes of manually turning it over and it fires up ran all day. Does this almost everyday since and now shuts down while driving after hard acceleration and surges under acceleration when on incline or underload. Changed fuel relay, fuel filters. Researched and asked around but getting mixed opinions. I am mechanically inclined but this is a little beyond my scope of trouble shooting and id rather not start throwing parts at it.
View 1 RepliesFord Super Duty (1999-2016) :: 2011 F350 - Shifts Hard When Cold / Cool
I recently purchased a 2011 F-350 w/6.7 diesel. When I first start it & let it run say 30 seconds and take off it shifts fine from 1 to 2 but when it goes from 2-3 it hangs there a second and then finally shifts into 3rd hard. 3rd to 4th is ok but 4-5 again is a hard shift and from 5 to 6 is OK. It will do this for a while like through the neighborhood and down the road 10 miles then it is fine. Shifts beautifully when warmed up.
My local Ford dealer has a guy that is supposed to be very knowledgeable with Super Duty trucks. I have had it to him twice and he says this is normal. All shift hard until the transmission is up to operating temperature. Says the engine is very powerful and until everything is up to temperature this will happen. If so then it would be normal to let it sit and run for a while before you take off in the morning. I am getting ready to hook the truck up to my 33' camper and go on our first camping season with the trailer/truck combination and if I need to leave it sit and warm up I will.
Ford Super Duty (1999-2016) :: 2002 F350 7.3 - Cranks Good But Hard Start?
Dealing with a 02 f350 7.3 powerstroke . The engine cranks fine . It fires but won't start smoke coming from exhaust while cranking and firing so seems to have good fuel . When it does start it misses for a few minutes and blue/white smoke . When the miss ends so does the smoke and starts fine after that and runs great until it sits for 12 or more hrs . Then back to same start issues . Fresh oil ,new glow plugs, new cover gaskets , glow plugs test at 1.3 ohm across all 8 of them , no voltage drop through glow plug relay , good voltage to each glow plug when tested right at glow plug terminal on each feed right at glow plug , fuel filter housing stays full doesn't seem to bleed back , high pressure oil pump pressure test was high enough to trash a 1000 lbs gauge in 2 to 3 revalutions of engine when cranking . Tested at presure sensor port .
View 2 RepliesFord Super Duty (1999-2016) :: 2008 F350 4WD - Clicking Noise Only When Turning Hard Left
'08 F350 6.4l 4wd, I had the truck come in with a exploded transfer case. (See pics). Ive read all about this happening to many others. The truck still drove, hubs not locked, plenty of fluid in the TC, pretty sure it was the double Cardan that did it. Anyways I replaced thwith TC, replaced the front driveshaft, filled the TC with recommended fluid. Test drove and drives great, shifts fine. Only until I turned left.
At slow speeds turning hard or 15-20 taking a turn, it sounds like a ratchet clicking from somewhere on the left side, right around the drivers door, from what I can hear from the cab. Does it in 2wd, 4wd hi/low, hubs locked or not. I changed the vacuum pump, no leaks, changed the IWE solenoid, pulled out both locking mechanisms, tightened crossmember, checked everything from the hours of research I did on the internet. I cannot find the problem. I don't know what else to check. Front axles free spin and lock when they are supposed to. I'm at the end...
Ford Super Duty (1999-2016) :: 2005 F350 - Hard To Turn On After Head Gaskets Replaced
I have a 2005 F350 6.0 PowerStroke, and I just did the head bolts upgrade to the ARP studs, new EGR cooler and a new stock turbo. Looks like everything came out good, no left over parts or unplugged connectors, all new fluids and fuel filters and oil filter. Did the priming of fuel and oil, the turbo. When it was ready to turn it on, I turned the motor by jumping the starter to build some oil pressure.
Now I turn the key to turn on the truck, it turns with no issues, it sound good, but it will not turn on.
Checked my batteries, they are fully charged, checked fluids, ok, checked oil pressure as I'm cranking it, it looks good.
It still does not turn on.
So, I jumped it with my friends Excursion, after a couple of tries, it TURNED ON.
Let it run for about 3 minutes then turned it off. It sound good just like it did before the upgrade, with an exhaust leak from the turbo.
Went to turn it on again, it turns but it will not start, jumped it again and it RUNS.
Now I let it run for about 30 minutes figured out where the exhaust leak was coming from.
Shut it off, Re seated exhaust pipe with leak, WENT TO TURN IT ON AND IT WILL TURN BUT WILL NOT RUN.
So what checks I can perform to start eliminating possible issues.....
Ford Super Duty (1999-2016) :: 2011 F350 - Hard Starting / Cranks Through 2 Cycles Sometimes Before It Fires
My 2011 f-350 6.2l cold starts hard, it cranks through 2 cycles sometimes before it fires, then it might stall. Sometimes it stalls if I put it into drive or reverse before its warmed up. It has also misfired on one or several cylinders during startup. It has also misfired while driving. It has never stalled when driving. I have replaced the canister purge valve, I have done a full tune up with all factory plugs. All with no change to how it starts. My next step is a Pcv valve, I have one coming from ford today.
View 5 RepliesFord Super Duty (1999-2016) :: 2001 7.3L F350 - Transmission Starts Shifting Hard And Grinding Gears
My buddy's 2001 7.3L F350 has had 3 transmissions. Rebuilt and used. Once the new trans is in he goes like 15 miles and then is starts shifting hard and grinding gears. What this could be?
View 8 RepliesFord Super Duty (1999-2016) :: 2001 F350 - Parking Brake Pedal Is Extremely Hard To Push
I have a 2001 F-350 Diesel 4x4 crew cab 8ft bed dually 7.3 diesel 6 speed. The issue is that the parking brake pedal is extremely hard to push. One day it pushed down and ratcheted into a locked position as normal and the next day I couldn't push it more than an inch down. I have rear disc brakes with internal drums in the rotors for the parking brake assembly. I replaced the shoes and hardware (which were fine) and I still have the same issue. I removed the front single cable from where it splits into the two rear ones and the foot pedal depresses smoothly and with the touch of a finger with no load on it. What else is it? The only other thing is one of the rear cables unless I am missing something?
View 5 RepliesFord Super Duty (1999-2016) :: 1997 F350 - Codes P0327 And P0629 - Hard Shifting But No O/D Light Flashing
I have a 97 F350 5.8 with E40D trans. I bought the truck with it shifting hard thinking maybe a simple filter/fluid change would fix it. It may have worked a little but did not fix the issue. There were 3 or 4 codes that I have already cleared up with new parts. I am still getting a 327 (something with EGR?) and 629 (Converter clutch control circuit failure). These show up in KOEO and KOER self test. The O/D does not flash ( bulb does work).
Parts that have been replaced: VSS, MLPS, new connector going into solenoid pack (tabs were broken), TPS. Removed the trans wiring harness and there is no damage or loose connections. When I replaced the solenoid connector I noticed there was some trans fluid in the connection. I cleaned it the best I could and reinstalled with dielectric grease.
The truck runs fine and shifts in and out of every gear fine its just shifting hard. If I unhooked the battery it will shift perfect for 5-10 minutes but then the hard shifting returns.
The only other thing I can find with my research is maybe the solenoid pack needs replaced. I figured if I take it somewhere they are going to want to rebuild/replace transmission. It seems like it can't be something very major since it will shift fine when reset...