Ford Super Duty (1999-2016) :: 2002 F250 Diesel - 4 Wheel Drive Just Stopped Working
So one day my 4 wheel drive just stopped working, when I put in 4hi nothing same with low, the light on the dash doesn't even pop up and it doesn't engage. I've done about everything I could think of doing besides replacing the motor for it and the wiring, I hate getting stuck...
View 4 RepliesFord Super Duty (1999-2016) :: 2003 F250 - 4 Wheel Drive Is Not Working
Love my 03 lariat Super Duty, King Ranch. Just found out 4 wheel drive is not working. Checked fuses, next going to look at the vacuum system, make sure its working. New to the Diesels but going to work at it and learn at the same time. 2003 F-250 4x4 ....
View 5 RepliesFord Super Duty (1999-2016) :: 2006 F250 - 4 Wheel Drive Solenoid Location
I have a 2006 F250 Super Duty w/ turbo Diesel. Took to dealership for "hopping" feeling when turning sharp. Was told that 4 wheel drive solenoid was bad. Where this solenoid is located? I know I can fix but want to know where it is located.
View 6 RepliesFord Super Duty (1999-2016) :: F250 V10 - 4 Wheel Drive Hubs Are Not Working With The Vacuum
I recently picked up a '99 F250 Super Duty with the 6.8L V10 for a song.
The 4 wheel drive hubs are not working with the vacuum. If I use the manual lock on the hubs all is well. I ordered the Innova 31703 CarScan OBD2 + OBD1/ABS/SRS Scan Tool. It says it does Trans codes. I am hoping it will cover the 4 wheel drive too.
Maybe related, the heat is always on. Meaning I feel heat at my feet when the temp dial is cold and fan is off. I can't find the heater control valve to check the vacuum line.
Ford Super Duty (1999-2016) :: 2002 F250 V10 Rough Idle / Not Running Perfect
I have an 02 f250 V10 with a rough idle (90K Miles). It's not horrible but it's obviously not running perfect. Everything seems ok when I am up and driving, especially at freeway speeds. I recently noticed that if the truck is in park and I run the RPM's to 1500 or 2K and quickly let off the gas it will die. It never throws any codes. So far I have replaced the IAC Valve, fuel filter, O2 Sensors, PCV valve, cleaned the MAF sensor and replaced the air filter. Plugs and boots were replaced 5K miles ago. Fuel trim levels on both banks are running around -3.1 to positive 3.5 based on what the computer is telling me. Also according to the computer the vacuum sits steady around 25 at idle (+ or - .2). I don't have a manual vacuum gauge, just relying on the computer. I've also gone around to every plug and disconnected both the injector wire and the COP wire and they all seem to equally affect the idle as well as the fuel trim levels.
View 11 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Engine Running Rough And Vibrating
I have an 02 f250 5.4. I just did the intake manifold. I also changed the spark plugs and the valve cover gasket. Following this I drained the oil and filled it with fresh oil.
It started right up but it felt like the engine was really vibrating and running rough. The check engine light than came on. I don't have one of those tools to diagnose it.
What could be wrong?
Ford Super Duty (1999-2016) :: 2002 F250 V8 Running Rough - Code P1152
My truck has been doing this for a while now but it has progressively gotten worse from about three months ago when I went through some deep water. I don't believe it had to much to do with the water, I just think that the water is what didn't deal the situation and lead to the problem becoming more prevalent. But continuing, yesterday it got down into the high 20's and my engine started acting up (rumbling coughing, surging while at/leaving complete stops) and then it finally through a code for once and I head over to the neighborhood AutoZone expecting to get a lean code (because when the engine is acting up really badly I can unplug the fourth cylinder fuel injector without the engine acting any differently) but instead I received the p1152 (bank two lack of switching (rich)) code....
At this point I believe it is a faulty fuel pressure regulator, but without a good diagnostic obd2 reader or a fuel pressure gauge I'm not sure what to do. I'm currently in college, money is low, and I'm trying to take an accurate shot at the part that needs to be replaced so that I don't have to buy more than one part. Of course AutoZone says o2 sensor but I changed both about five months ago.. I've been chasing this diagnosis around for way too long now. (It's on a 2002 ford f250 5.4l super duty)
Ford Super Duty (1999-2016) :: 2002 F250 V10 Rough Idle / Misfire Under Load
I have a 2002 F250 CCSB Lariat 4x4 with the Triton V10, I'm up to 232,000 miles so far and fairly happy with the old girl. Just this weekend, I noticed some hesitation when at idle and even more rough running when under slight load. The misfire/hesitation is worst when going up a slight hill, when the truck is accelerating at low RPMs.
I am getting zero trouble codes or freeze frame conditions on my scanner. What should be my order of diagnosis? Vacuum test at line from PCV to TB, COP test? EGR inspection? Plug inspection? Also, how do you test a coil if resistance is not a reliable method?
Ford Super Duty (1999-2016) :: 2002 F250 - Front Wheel Bearing Noise
2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
Ford Super Duty (1999-2016) :: 2002 F250 - Clunk In Front End / Felt In The Floor And Steering Wheel
I have a 02 F250 4x4 5.4. As I drive and when pulling into a driveway I hear a clunk that can be felt in the floor and the steering wheel. I've replaced the wheel bearings and seals, shocks, ball joints, sway bar links and bushings, tie rod ends at the gear box and "right hand inner". The other two tie rods are tight and so is the track bar. I cannot duplicate the sound if I jack it up and move parts around with a pry bar. I can however move the steer box sector shaft upwards about an 1/8. I've adjusted the screw but it didn't do anything. Could it be the steer box or the springs? I've even mounted a GoPro underneath but everything moves and I can't tell why it is.
View 14 RepliesFord Super Duty (1999-2016) :: Front Drive Shaft Spinning While In 2 Wheel Drive
I have a 1999 Ford F250 super duty 4wheel drive, lifted (really a leveling kit but had to lift rear to compensate), 5.4l. Im having a problem with my front shaft turning while in 2 wheel drive. Hubs aren't locked and its in 2 wheel not 4. I've taken hubs off and the bearing spins free soo I know its in auto. Why is the drive shaft still turning???????
View 5 RepliesFord Super Duty (1999-2016) :: F250 V10 - Over Drive Not Working?
1999, F250, SD, v10, Auto, 4x4.
My light on the overdrive is not coming on and the overdrive does not seem to be working. I had a new transmission installed a few weeks back. Wasn't working prior to this.
Ford Super Duty (1999-2016) :: 4 Wheel Drive Low Not Working
Checked the EOF vacuum lines and pump but still have a problem. The EOF works and locks the hubs when I switch to 4x4 high, Easy to feel when you turn the wheels but it will not go into low. The light on the dash does not light up the word "low".
View 1 RepliesFord Super Duty (1999-2016) :: No 4 Wheel Drive When Shift Into 4Lo
When I shift into 4Lo I get no 4 wheel drive. 4Hi works. Did have a/c redirect to defrost a couple of times. I remember something about the air redirecting having something to do with not having 4x4 but don't know just what it was.
View 8 RepliesFord Super Duty (1999-2016) :: F450 Revs Up But Drives Very Slow
I have a 1999 F450 Diesel dump truck. Automatic. The problem that I have is that the truck will drive VERY SLOWLY while the rps go up.
You can hear the engine revving up, and a strong air sound when doing so (do not know if intake or exhaust, but its like a strong wind sound. And not like a hiss, so I do not think its a vacuum leak).
The transmission goes through gears fine, but it does the rev up thing through every gear. So I am wondering if something like the torque converter might be broken or slipping.
For example, if you go with the loaded truck up a hill, you have to really push it to keep any type of speed. Or when you get off a red light.
When I bought it used, I thought that it might have a really short final gear. But that would not explain the high RPM and no push.....
No codes at all.
Ford Super Duty (1999-2016) :: Front End Hop When Only Turning Right In 4 Wheel Drive
1. Why does my front end hop when only turning right in 4 wheel drive?
2. O nly one of my back tires spin, so does that mean that when I put it in 4 wheel drive I only have 3 tires spinning?
oh I got a 2001 xl 5.4 f250 and is this normal
Ford Super Duty (1999-2016) :: 4 Wheel Drive Locking Hubs?
My 2009 F-350 4x4 has a front wheel option of Auto or Lock ; I think I understand the Auto option but under what circumstances would I lock the hubs and is it safe to leave them in the Lock mode when traveling on the highway?
View 5 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Hard To Drive Under 40 MPH In 3rd Gear
I recently purchased a 00 F250 psd 4x4. Other than doing all of the fixes it needs to make it ride better I have been questioning the trucks "get up and go" and the EXTREMELY sensitive skinny pedal. Truck seems to pull very hard and puts out some black smoke under hard throttle but nothing like the really tuned trucks I have seen. But the skinny is so sensitive its hard to drive under 40mph in 3rd and once it gets up to 55 or so its real sharp getting on and off the throttle. Trans shifts great, TC locks and unlocks, truck runs awesome IMO but just a bit harsh. Is there a way to find out if it was tuned prior to me buying it other than inspecting for a chip, or is this the way they are and I just have to get used to it more...?
View 9 RepliesFord Super Duty (1999-2016) :: 2007 F250 - Drive Shaft Installation
My elderly neighbor has asked me to re-attach his drive shaft on his F250.
Said his wife was driving and it broke the u joint or something, and he has gotten it repaired and wondered if I could put it back on. Has been sitting for a bit from what he said.
Just need to know, how I should clean up and or grease? the end with the boot on it. before I put it together. The boot looks to be zap strapped, is that standard?