Ford Super Duty (1999-2016) :: 2001 F350 Manual Trans 4x4 - Temp Gauge Not Working
I replaced the sensor on top of the water pump and the gauge still doesn't work. I tested the gauge by unplugging and grounding out the wire and the gauge goes all the way up. What I can try next. I didn't get a Motorcraft sensor so I'm going to go get one of those tomorrow hoping the duralast wasn't correct even though it looked 98 percent identical to the original. 7.3 lite diesel.
View 1 RepliesFord Super Duty (1999-2016) :: 2001 F350 - Temp Read-out On Mirror
I have a 2001 F350 and the temp read-out on the mirror hasn't worked since I got the truck in 2004. Where the sensor is. I found a connector on the back side the core support on the driver's side that has nothing plugged in. Could this be where it should be?
View 4 RepliesFord Super Duty (1999-2016) :: 2001 F350 - Trans Temp Sensor 4r100 Installation?
I have an isspro sensor that I need to install on my 4r100. I have it all installed except for the actual sending unit. My question is where is the best place to put it?
I've watched multiple YouTube videos and it seems a lot of people use the test port on the driver side above the linkage. I found out the hard way that it is a very poor choice of location. A lot of people say that the best way is to drop the pan drill a hole and weld in the bung? I was wondering would it be possible to put it on the "out" line on the transmission oil headed to the cooler? 01 f-350 7.3
Ford Super Duty (1999-2016) :: Transmission Temp Gauge Always Point To The Middle
I have an 02 F250 V10. Ive always wondered about the transmission gauge. It seems to always point to the middle of the gauge range. This weekend I was pulling my car hauler up and over the Ozark mountains, and when I stopped for fuel I noticed the transmission was vomiting fluid underneath the truck (and on my exhaust creating a nice smoke bomb for everyone around me). The gauge indicated normal temps. It kind of gave me a sick feeling. I have ordered the 6.0 Trans cooler from Rock Auto and a new temperature sending unit. Do the trans temp gauge is supposed to move or is it pretty much useless?
View 14 RepliesFord Super Duty (1999-2016) :: Engine Temp Gauge Pegged Out And CEL Came On - P1299 Code
My truck threw a code p1299 last night on my way home from the lake. I was towing on a huge grade and all the sudden my engine temp gauge pegged out on me and check engine light came on. I pulled over and noticed a bunch of coolant had overflown the cap but the engine didn't seem to have over heated. When I restarted the truck the engine temp was immediately normal range. I drove for another 30 min or so and the engine temp started to climb and then come back to normal then climb and stay pegged. I pulled over again and noticed the coolant level was low and coolant had overflown the reservoir. I restarted the truck and once again it was normal. I just drove surface streets the rest of the way with no issue. I suspect blown head gasket. This is a 2003 F-250 6.8L with 100000 miles.
View 8 RepliesFord Super Duty (1999-2016) :: 2006 F250 - Digital Temp Gauge Not Working
I got in my 06 f250 tonight and my digital read out on my temp control not working. My heater and A/C works but when I turn it off my outside temp is not on. Whats going on?
View 3 RepliesFord Super Duty (1999-2016) :: 2008 - Truck Wouldn't Start Whenever Temp Gauge Working While Hot
I have had this issue with the truck 2008 F-250 6.4L since I bought it a year ago. At first it seemed as if the truck wouldn't start whenever the water temp gauge was working while she was hot. When the gauge wasn't working she would start right up like a champ. Well a year later ( have only been driving it for 6 months) a full engine rebuild, new high pressure fuel pump ( injector pump on top the engine below the turbos) she still won't start when she is hot. What the issues are.
Right after the engine rebuild I was getting the p088 code which is for the hpfp but since I cleared the codes right after the engine was rebuilt I haven't gotten the code again. I replaced the high pressure fuel pump this last weekend hoping that it would solve all of my issues and she would be like brand new again, but it didn't do anything. When I ran codes right after I installed the high pressure fuel pump I got a few codes p0684 which is the glow plug control module p0284 ( google said) gear lever y position correct but I'm unsure if that's right.
P0528 which is the fan speed sensor circuit ( that was unplugged during the removal of the hpfp and power steering pump or the radiator) p0480 cooking fan circuit ( also unplugged ) p174e out put shaft wheel speed correlation ( not concerned about that one) p008c fuel pump control circuit p008d fuel cooler system ( taken out and unplugged using installation of new hpfp) p115a ( low fuel level forced limit power) that is from trying to start while she had a little bit of air in the system after replacement) p2291 injector control pressure to low- excessive cranking ( probably from the air in the fuel system again). I cleared all those codes once I got her up and running again. Checked for codes yesterday and the only one that came up again was the p0684. Where to check next for this hot start issues,and don't know what to do at this point.
Ford Super Duty (1999-2016) :: Temp Gauge Spiked - Cold Air Blown When Turned Heat On
I have been having a problem with my 2002 F250 Super Duty 4x4. It started about 2 months ago. I was in traffic (truck hadn't even been on for 15 minutes). The temp gauge spiked, so I pulled over and turned the truck off. I turned the ignition on and the gauge was normal so I started it and all was fine.
Fast forward a little and every so often about every 3 weeks it would overflow (coolant) but not get to the point that it would overheat. I changed the thermostat and all seemed good to go. Fast forward to yesterday morning. Got in the truck and left to go hunting, and I didn't even make it 10 minutes down the road when I turned the heat on and it blew cold.
I started to see the gauge creep up so I pulled over and shut it down. Upper hose was cold, lower is cold and both heater hoses are cold. After some time of waiting, I started it but the gauge kept creeping up and no heat, so I kept shutting it down. After about 5x of this, the heat worked and the upper hose got hot and all was right with the world. SO I drove it home. Coolant is new, flushed about a month ago and was running great since then. Thermostat is new. Do I have a blockage somewhere? Water pump bad?
Ford Super Duty (1999-2016) :: Temp Gauge Pegs Over 250 And OD Light Flashes Steadily Going Uphill
When I purchased my truck 1999 F350 about 5 years ago, I was told it was on its third transmission since the awesome 7.3 diesel engine has 200,000 miles on it. At first I noticed that going up a hill with the truck empty would cause the tranny temp gauge to climb to 250 degrees F. Nowadays when I tow my boat or carry my camper, the temp gauge pegs over 250 and the overdrive light flashes steadily when I do any hill climbs. I have had the fluid flushed several times, and I have a large fan powered oil cooler too. I also recently noticed that the tranny heated up when the truck is just idling in place.
I just got back from burning man and during the 800 mile round trip the overdrive light started flashing at least 6 times and the temp gauge read over 210 the whole time, with it pegging over 250 during hill climbs. No fluid boiled out but I am very concerned that damage is being done.
Is it possible there is a clog in a line somehwere restricting the flow of oil? Or should I replace the tranny?
Ford Super Duty (1999-2016) :: Overheating But Gauge Stays In Normal Operating Temp Range?
Ok so here here goes I have a 1999 f250 super duty with 5.4 triton it seems to be over heating but the gage stays in the normal operating temperature range. I just changed the water pump. Could it be the thermostat and Would it hurt to remove the thermostat until I can get one...
View 8 RepliesFord Super Duty (1999-2016) :: . 2000 F350 - Gauge Cluster Tear Down
I have a 2000 F350. I'm tired of my gauge cluster. No matter what, within a year one of the LEDs has a diode that starts to flicker and flash and makes my gauge cluster dance. I'd like to solder in a series of individual LEDs and do away with the expensive bulbs that always fail. The bulbs I soldered into my HVAC have never given me any issue, so I figured this would be a good fix for that and the awful hotspots.
I have torn down the gauge cluster partially before. when you pull the gauge faces off as a unit (including the various electrical components tied to the back of the gauges), there is a circuit board at the top of the cluster. It has two cables that plug into the main face part that pulls away from the white plastic chassis. Need to successfully unplug the cables in order to separate the gauge assembly from the chassis? I don't like the idea of soldering so close to it while having the chassis part propped up.
Ford Super Duty (1999-2016) :: 2008 F350 - Trans Temp Sending Unit Replacement?
The trans temp guage on my '08 F-350. V-10 started acting erratically, and the wrench icon popped up on the display. i crawled under the truck to look for the sending unit and it's lead. i assume that i found the lead. it is encased in a corrugated sleeve, and appears to be a vaccuum type tube and boot connector? the boot still had a small round gray cap plugged into it. it appears that the cap was never glued (go figure) upon assembly. i have tried to reach up on top of the trans to find the sending unit to figure out the best angle of attack. i can barely touch it with the tip of my finger. going with mechanical guages is out of the question at the moment, so i'm wondering can it be driven any distance this way, AND any schmooze tricks developed to get at the sucker without dropping the cross member or exhaust????
View 3 RepliesFord Super Duty (1999-2016) :: F350 Engine Temp Started To Increase - Code P1212 For ICP
1999 F350 SD ... Yesterday when goosin it to get on the highway my rig threw up a code quickly and engine temp started to increase. Once temp got in the red, oil pressure got a little figgity. The code was for the ICP(p1212), so I cleaned the plug and made sure coolant and oil were topped. This morning she ran barely over normal temp (stock gauge). This afternoon same thing as yesterday but without the code. When I let off of the accelerator temp goes down. I just got married so I have little funds to throw at a shop.
View 4 RepliesFord Super Duty (1999-2016) :: 2000 V10 F250 - Temp Gauge Suddenly Shoots To Max / Truck Goes Into Limp Mode
My F250 with V10 has developed an overheating problem. While driving, the temp gauge suddenly shoots to max, and the truck goes into limp mode. Turning off the truck and ignition, waiting a few minutes, and all seems to be well again - sometimes for only a minute, sometimes for several days. No steam leaking, the water in the reservoir seems to be normal temperature, the radiator is not overly hot, and the AC keeps on blowing ice cold. Me thinks it is not really overheating, it just thinks it is. So where to start? Change the temp sensor first, or the thermostat? It seems the hoses are fairly firm, I don't believe they are collapsing from suction.
View 14 RepliesFord Super Duty (1999-2016) :: 2003 F550 Truck Died While Running / Temp Gauge On Dash Dropped To Cold
The truck I'm working on is a 2003 f550 with a 6.0, and 382000 kilometers. My service truck died on me couple days ago, while running. As I rolled to a stop, I noticed that my temp gauge on the dash dropped to cold. (Truck was hot). Tried starting, and I have a crank, no start situation.
After towing it to my shop at work, I hooked it up to my scanner, and found that the pcm will not communicate with the scanner (otc genisis). I have no injector buzz with key on, wait to start light comes on for an abnormally long time. I have 48.3 volts on the ficm,(4 screw), and haven't been able to find any chafed wires as of yet.
Ford Super Duty (1999-2016) :: 2006 F350 - Long Cold Starts / IPR Is Maxing Out At 85% On The Gauge
I have an 06 F350 6.0 and I am having long cold starts. On the gauge the ipr is maxing out at 85%. This only happens when cold and have never had a no start issue. When hot the engine cranks right up and the ipr stays in normal range. FICM has been replaced. Does this sound like needing a new ipr only?
View 4 RepliesFord Super Duty (1999-2016) :: 2006 F350 - No Crank - Engine Sensor Data / Trans Temp Error
I have an '06 F350 dually with a 6.0 diesel. I bought this used about 5 years ago and for the most part have loved it. i would always smile on the inside when i heard people bash the 6.0...i thought i got lucky....until today.
140k miles. recent oil change. all is swell...until this morning. Stick in key and turn it. glow plug indicator comes on...all lights come on for a few second....wrench, abs, dtc etc....wrench shuts off...glow plug light comes on...4 or 5 seconds later wrench light comes back on....turn key and NO CRANK.
All fuses are fine...starter cranks if i jump the solenoid...but it won't start. Miles to empty and everything else is just dashes hit the OBD and it says "engine sensor data error"/ "trans temp error" ...
Ford Super Duty (1999-2016) :: 2005 F350 - Gauge Light Started Flickering - Instrument Cluster?
I have a 2005 F 350 with a 6.0 Diesel! My heat quit on my wife and I the other night! I replaced some fuses and started the truck to make sure the heat was working and it was! So I thought while I am here I should replace some bulbs in the cluster that were out!
I took the cluster out, looked at the bulbs and they looked oK so I put them back in and put the dash back together! When I went to start the truck once I turned the switch on my gauges and lights started flickering on and off fast and all it will do is just click when I try to start it! I just had it running 15 minutes before this!
I went through all the fuses and if I take one of the relays out and turn the switch on all the lights and gauges seem to work right but when I try to start it, nothing! I replaced the relay and it starts flickering again! I had the relay checked at Napa and they said it was good! The relay was for the Powertrain module!
Ford Super Duty (1999-2016) :: 2001 F250 - Engine Temp Seems Really Low
2001 f250 5.4L v8. Engine temp seems really low. The gauge is reading barely above the cold in normal range. The heater is only blowing out 75 degree air at the warmest. It gets to its normal temperature with in 15 minutes even when its real cold out. I live in Minnesota and its been a really cold winter so having hot heat would be nice. I just bought this truck at the beginning of the winter. Whats going on?
View 14 Replies