Ford Super Duty (1999-2016) :: 2000 F250 - Clunking Noise When Turning
I have a 2000 F250 SD with the V10 engine. The problem that I am having with it as of late is that whenever I perform a full turn I hear some clunking coming from the front end. The clunking is similar to that heard from cars that use CV joints FWD but of course it sound more "manly"
Anyways, my truck has the full axle on front so I suppose it could be either the u-joint at the hub or the hub itself. I would like some pointers so I can acquire the required parts.
Ford Super Duty (1999-2016) :: 2000 F250 - Clunking Noise From Right Side Over Bumps - Front Axle Bearing
I bought a 2000 F250 V10 Super Cab. Oddly after a few weeks it has grown on me. There has been a clunking noise out of the right front over bumps. I traced it to a bad axle bearing. The u joint moves up and down about a 1/2 inch. Besides pulling the hub/bearing assembly out and removing the axle are there any surprises getting the old bearing out?
View 1 RepliesFord Super Duty (1999-2016) :: 2000 F250 - No Key To Lower Spare Tire
OK, I never heard of any "key" to lower the spare tire. However, the nice people at Discount tire weren't able to swap my tire because I'm missing some "key". How do I get a key for this and ELIMINATE the need for the key? 2000 F250 Crew Cab 4x4.
View 3 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Passenger Side Tire Wearing Off?
I just got my 2000 f250 a couple of months ago and my passenger tire is going balled but my driver side tire is fine this is my first ford truck so I don't know much about them. I have a tug in the steering as well...
View 3 RepliesFord Super Duty (1999-2016) :: 2014 F250 - Rear Seat Back Removal?
I've got a 2014 f250 xl super cab and can't for the life of me figure out how to remove the back seat back.
View 2 RepliesFord Super Duty (1999-2016) :: 2000 F250 5.4L Just Quit While Off Road And Wouldn't Start Back Up
I have a super duty with the 5.4 in it. it just quit while off road n wouldn't start back up. pulled it back to camp, wiggled wires around cam n crank sensors n it fired up n stalled numerous times then just wouldn't even fire back up. loaded on trailer n brought home, buddy put his tester on there n said there was no rpm reading so I replaced the crank sensor, it fired up n stalls still. wires seem to be good to crank n cam sensors. don't have a manual to tell me what relays are what.
View 11 RepliesFord Super Duty (1999-2016) :: 2004 F250 4X4 - Front End Rumble - Squeaking / Grinding Noise Then Clunking
So to start at the beginning.... Traveled across Canada East to West towing 11000lb travel trailer, no problem. Have used 4x4 in a few campsites to pull out of a pitch without spinning the wheels and causing damage to the site when it has been really wet. All good.
Got to Banff in December and the town was an Ice rink, engaged 4x4 and all good. Crossed the Rockies and the 4x4 starts making grinding noises. Up and down some mountains and squeaking, grinding noise then clunking.
I have manual hubs, disengage and the noise all goes away. Engage 1 hub and no noise. Engage both hubs, noise back.
I bought some needle bearings and went to swap them. Got hubs apart and they look good. No scoring on the drive shafts. They are not dry, but as I have them open, repack them with grease anyway.
Do more research... Remove ABS sensor and repack main bearings with grease. (broke one sensor pulling it out, too cold plastic brittle oops). Still clunking noises.
The universal joints look good, doesn't appear to be any play in them. However, the axle seal (knuckle seal) (F81Z-3254-CB) does move around a lot in it's metal casing. It is tight on the shaft, but with the hub off, I can move it in and out, and move it side to side. If I had ESOF hubs I guess they would not be locking as I'm sure there would be no vacuum in there!
Question is then, would this seal be allowing the universal joint to wobble under load in 4x4 mode? Would this wobble be the cause of the rumble? As it is labelled as a seal and not a bearing, I wouldn't of thought this would have been a loaded point, and the weight would have been taken by the associated bearings and it could be run without this seal? But if it is not this, then I'm still looking for a clue as to what is making the rumble....
Ford Super Duty (1999-2016) :: 2000 F250 - Rear Hub Seal Leak?
I have a 2000 F250 4x4 7.3 - About a month ago I drove across town and then noticed a strong hot brake smell from the rear of the truck. When I drove home about 2 hours later it was gone and didn't return until today. Today I stopped at a light with my window down and got the same hot brake smell, looked in the mirror and saw smoke coming from my drive's side rear wheel.
I carefully drove home (the smoke was now gone, all i did was cycle the parking brake release a couple of times) and pulled the wheel off. Rotor was really hot but smooth and clean. Brake caliper and pads looked great (no sign of the pads glazing or dragging, dry as a bone). The inside of the rotor was wet with oil. The brake shoes and components were soaked with the same fluid/oil.
Does this sound like a typical hub seal issue? Excuse my ignorance since I haven't had the rear hubs apart before but does the gear oil in the rear diff go into the axle tubes? I know the front tubes are dry but I didn't know if the rears are different. The amount of fluid on the brakes seems to be more than the little bit that is inside the hub. I need to pick up the parts and rent/purchase a couple of tools to replace the seal so I want to be as sure as possible that I'm on the right track...
Ford Super Duty (1999-2016) :: F250 Started To Shake When It Idles
I have a ford f250 with a 5.4l 2v engine and lately it started to shake when it idles. i have changed all the ignition coils and spark plugs, the injector are fine, but i cant seem to pinpoint the problem. the weird thing is that there are no codes. the fuel trim on bank 1 is around -8 and bank 2 is at almost positive 20 and higher.
View 14 RepliesFord Super Duty (1999-2016) :: 2011 F250 Shake At Highway Speeds Around 70 To 75 MPH
I have a 2011 f250 6.2 cclb and it shakes around 70 to 75 mph. Not terribly but enough to annoy the crap out of me. Now I have put new tires on it recently, new Rancho 9900 adjustable shocks, I have it aligned regularly and tires rotated and balanced every 5000 miles or so. I have had two dealerships look at and my local shop and they can't see anything visibly wrong with it.
View 7 RepliesFord Super Duty (1999-2016) :: F250 Started To Shake For At Least 3 Or 4 Seconds While Driving
I was driving my 99 f250 superduty and out of no where it sounded like i had blown a tire started to shake for at least 3 or 4 seconds pulled to the side of the road got out and check tires were good, got back on the road with no more problem.
View 1 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Violent Shake In The Steering Wheel Mostly
I have a 2004 superduty 250 4x4 with the 6.0. I am having a violent shake in the steering wheel mostly and can feel it in throttle at about 45 to 60 and at 72 there is s growel. Have changed tires, wheels checked all ball joints tie rods wheel bearings ujoints. Don't matter brakes on or off, od on or off nothing changes it. I really don't know what else to check.
View 10 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Rear Driver And Passenger Windows Would Not Raise Or Lower
My son recently purchased this truck in Jan., 2017, upon inspecting the vehicle we noticed the rear driver and passenger windows would not raise or lower. When I asked the seller about this his comments were " I believe it to be a master switch issue". Ok so no big deal, I purchased and replaced the master switch with no luck. I didn't spend much time on it due to the cold weather. After digging into this a little more I'm very confused now. So here is where I currently am at with this issue.
Power is not the problem, I am reading approx. 14V at the master switch and at the rear door switches. I've checked and have power when the switch is toggled to simulate raising and lower of the window (approx. 12 to 13.5V). The window lift motors have been taken out and cleaned and inspected. The motor will operate properly with a 12V battery pack (both motors, driver and passenger side). I have power all the way to the motor itself, slightly less than 14Volts.
I can raise and lower the window in the truck by plugging into the back of the female connector with the outside power source but not with the power supply from the truck. I have continuity between the power(blue) and ground(black) wires at the switches. So this is where I am at, also just a reminder the front windows and door locks work fine. Just a side note, this truck has aftermarket mirrors on it so that branch of the harness is left hanging.
Ford Super Duty (1999-2016) :: 2000 F250 - Clicking Noise And Dinging When The Key Is Off Or Out
So, yesterday when I got home I stopped at the barn to unload a few bails of hay and when I got back in to crank it, nothing happened. I turned the key and nothing, so I figured I would just worry about it today. However, when I turned the key back to off and started to take it out all sorts of stuff started to happen. There was a clicking noise and a dinging, not like when the door is open. It was quicker. Also, when I turned my key back on none of my dash lights or radio came on. Nothing happens now, except the strange clicking when the key is off or out. The first thing I thought of was the GEM or fuse box.
View 3 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Manual Transmission Noise When First Started
I am new to being an F250 owner. Just recently purchased a 2000 F250 SD 4x4 with the 5.4 and a 5 speed trans. Got a pretty good deal on it, because I knew some work had to be put into it, and do plan on dropping the trans. Currently, if the truck has been sitting for a little bit, not cool, but not running for a little bit, when I start it, whether it is in gear or in neutral, there is a noise coming from what seems to be the clutch area.
After a couple minutes of driving, this noise goes away and all sounds as it should. A little bit of researching turned up the possibility of the throw out bearing being bad, however, I found other posts online that doubt this. Another symptom that I assume is connected is that if I go to put it in reverse at 0mph from neutral, it grinds.
In order to go into reverse, I have to press in the clutch, put it in first, then put it in reverse, at which point it goes in no problem. I had already planned on replacing the clutch because it seems to me that would be the logical choice as to where the problem originates, so no issue there. But perhaps I'm wrong??
Ford Super Duty (1999-2016) :: 2000 F250 - Making Ticking / Knocking Noise
I have a 2000 F250 5.4 that has a ticking/knocking noise. After about 30-60 seconds of first starting the truck in the morning, the ticking/knocking noise appears. It sounds like its coming through the exhaust system and seems to be louder under the front passenger side wheel well. When I rev the engine up, it seems to go away. Does this engine have a cam phaser? Could it be timing chain slap?
View 11 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Loud Banging Noise When Going Over Bumps
I have a 2000 F250 2wd 6spd with a loud banging noise that has been vexing me for quite sometime now. The bang happens when I go over bumps (even small ones like road reflectors) while driving. I don't think it is suspension related since all the ball joints, front/rear swaybar and endlink bushings have been replaced fairly recently. All the springs and bushings also look okay.
The noise seems to come from the rear, and I notice that if I let off the gas when I go over a bump, it does not make a sound. Conversely, if I am accelerating aggressively and hit a bump, the sound is much louder. Also, if I step on the clutch while keeping my foot steady on the gas, it makes a bang. Jumping up and down in the bed while the truck is parked does not recreate the sound. I have already greased the driveshaft spline joint so I'm thinking the sound might be differential or transmission related. What it could be?
Ford Super Duty (1999-2016) :: 2000 F250 - Installed Clutch Now Grinding Noise?
2000 Ford F250 crew cab 4 x 4 with 7.3. 6 speed transmission.
I just had a new clutch installed and now I am have a grinding noise when putting it into 1st gear and when I change from granny to first it will grind also. I did not have this issue before having the clutch replaced.
I have also just had a new hydraulic clutch kit installed.
Ford Super Duty (1999-2016) :: 2000 F250 - Sloppy Steering And Noise In Front End When Going Over Bumps
My 2000 f250 7.3 has pretty sloppy steering and noise in the front end when going over bumps. I have replace the drop links, swap bar bushings, both wheel hubs including new seals and the drag link. The rest of the front end seems to be in good shape. I put it up on jack stands and there is some movement in the front end but it seems to all be in the steering box.
Steering box appears to be original with 220k miles. I went to tighten it and it appears the PO did it at least once already. Is it safe to try tightening it again? Does tightening it increase the risk of failure? I'd like to try tightening it first but not at the risk of losing steering at 65mph with my kids in the truck.