Ford Super Duty (1999-2016) :: 2000 F250 - Sloppy Steering And Noise In Front End When Going Over Bumps
My 2000 f250 7.3 has pretty sloppy steering and noise in the front end when going over bumps. I have replace the drop links, swap bar bushings, both wheel hubs including new seals and the drag link. The rest of the front end seems to be in good shape. I put it up on jack stands and there is some movement in the front end but it seems to all be in the steering box.
Steering box appears to be original with 220k miles. I went to tighten it and it appears the PO did it at least once already. Is it safe to try tightening it again? Does tightening it increase the risk of failure? I'd like to try tightening it first but not at the risk of losing steering at 65mph with my kids in the truck.
Ford Super Duty (1999-2016) :: 2000 F250 - Clunking Noise From Right Side Over Bumps - Front Axle Bearing
I bought a 2000 F250 V10 Super Cab. Oddly after a few weeks it has grown on me. There has been a clunking noise out of the right front over bumps. I traced it to a bad axle bearing. The u joint moves up and down about a 1/2 inch. Besides pulling the hub/bearing assembly out and removing the axle are there any surprises getting the old bearing out?
View 1 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Front Suspension Noise - Loud Knock As If Left Shock Is Bottoming Out
I have a noise with my new (2.6k miles) 2000 Diesel F250 Crew Cab. When I make low speed, right turns while crossing any type of depression in the road I hear a loud knock as if the left shock is bottoming out. There's an intersection near my house with runoff depressions across the road, I almost always hear the noise when making that turn. I've occasionally heard it coming from the right side when making a left turn.
View 14 RepliesFord Super Duty (1999-2016) :: 2011 F250 - Clunk Noise When Going Over Bumps
When I go over good size bumps, I hear a clunk in the front tire area when my driver's window is down. It's a metal noise, like something loose.
2011 F-250 with 203K miles. Replaced shocks last year. Did this with stock wheels/tires. Something in the front suspension or axles. What should I be looking at?
Ford Super Duty (1999-2016) :: 2000 F250 - Loud Rumble Shakes?
Alright i got a 2000 f250 with the 7.3 and its stick, when i let off the clutch to start moving, and at low speeds like mainly 1st and 2nd gear. Right below the cab there's a loud kinda growling or rumble, it shakes the truck a bit til i start moving good. Then it goes away. But what it could be? I think pilot bearing.
View 5 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Rattling Noise Coming From Front Suspension When Going Over Small Bumps
2002 F-250 7.3 4x4 ...
I have a rattling noise coming from the front suspension (both sides) when going over small bumps. Most people point to ball joints, but I find my case odd because I just replaced
Upper/Lower ball joints
Track bar
Tie rod ends
Shocks
Front U joints
Drag link
I did not touch the leaf springs or the sway bar, except to grease the links, which otherwise looked good.
Ford Super Duty (1999-2016) :: 2004 F250 - Loud Whine Noise Comes From Under The Hood
I have a 2004 Ford F250 Turbo Diesel, egr delete, headstuds, intake, dual stacks, etc and when i turn my wheel a loud whining noise comes from under the hood, I noticed it put tension in my brakes. When I accelerate it gets louder and when i let off the gas it goes away... i checked my fluid in my steering pump and it was low so i put some more in and the next day it was all sitting under neath the truck.... any quick fix or do i need to replace the whole pump?
View 2 RepliesFord Super Duty (1999-2016) :: F250 - Engine Making Loud Air Rushing Noise
I drive a 2000 F250 5.4L. Currently has about 168,000 miles on it. I changed the oil the other day and cleaned the air filter. I used what I usually use on the oil change which has never been a problem. But this is first time to clean the K&N filter. A day or so later my engine is making a loud air rushing noise. Under throttle the engine compartment sounds like a wind tunnel. At 3500ish rpms it makes a harsh whistle noise. The air rushing noise doesn't go away once its warmed up or after the engine has been cool. Noise didn't go away with the filter being taken off either.
Could all of this be caused by cleaning and not using k&n air filter oil (but rather WD40 upon Dad's suggestion)? Or is there something else going on?
Ford Super Duty (1999-2016) :: 2006 F250 - Intermittent Loud Chirping Noise
I have a 2006 f250 lariat 192k no mods except k&n filter everything is stock. I have 2" pro comp level kit and a scan gauge 2 nothing fancy! Well the other day I noticed my truck was chirping like a Chirp chirp chirp...... Chirp chirp...... Chirp chirp chirp! It goes up and down with the rpm's but it's comes on and off only when the engine is up to running temps the belt does squeak during warm up but I don't think that's it, it's coming from the back of the engine I'm sure of it because I used a paper towel tube and listed right in the turbo hpop area on top of the engine but it's too hard to tell I can't find exactly where it's coming from, some people I've had listen think it's a belt or pulley or tensioner! But I'm not sure if it is because I've sprayed water, and wd40 on the belt and pulleys with no change!!! I'm afraid it's a lifter or something inside the engine yet it's too loud and pronounced to sound like it's coming from the inside! I'm just lost!
View 8 RepliesFord Super Duty (1999-2016) :: F250 - Loud Ticking Noise For A Short Period (30 Seconds) On Cold Startup
6.2L F250 truck is just shy of 60k runs good however on cold startup there's now a pretty loud ticking noise for a short period (30 seconds) until it warms up then it slowly goes away. Once its warmed up there isn't much of anything.
Did these have exhaust manifold gasket problems like the 5.4? Hoping that's it if not, any other common problems that would make that ticking noise and then go away quickly once the engine is warmed up.
Ford Super Duty (1999-2016) :: 2004 F250 - Loud Whining Noise / White Smoke From Serpentine Belt
I bought a 2004 6.0L F-250 used a few weeks ago. There have been a few problems here and there that I have been competent enough to fix. I am now facing a problem of A: the truck not starting (I believe it was just a battery problem, charged and started fine). But also B: I have had a slightly frayed serpentine belt that I noticed a few days ago. After I got the truck running from my the no-start and driving it around the block I parked it and went inside. Came back out a few minutes later and I tried to start it. It hesitated a little bit but started with a loud whining noise and white smoke coming from the belt. Turned the engine off and saw on one of the bottom wheels (pulleys?) some residue that looked and smelled like burnt rubber. Is this just simply a need for a new belt?
View 5 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Clunking Noise When Turning
I have a 2000 F250 SD with the V10 engine. The problem that I am having with it as of late is that whenever I perform a full turn I hear some clunking coming from the front end. The clunking is similar to that heard from cars that use CV joints FWD but of course it sound more "manly"
Anyways, my truck has the full axle on front so I suppose it could be either the u-joint at the hub or the hub itself. I would like some pointers so I can acquire the required parts.
Ford Super Duty (1999-2016) :: 2000 F250 - Clicking Noise And Dinging When The Key Is Off Or Out
So, yesterday when I got home I stopped at the barn to unload a few bails of hay and when I got back in to crank it, nothing happened. I turned the key and nothing, so I figured I would just worry about it today. However, when I turned the key back to off and started to take it out all sorts of stuff started to happen. There was a clicking noise and a dinging, not like when the door is open. It was quicker. Also, when I turned my key back on none of my dash lights or radio came on. Nothing happens now, except the strange clicking when the key is off or out. The first thing I thought of was the GEM or fuse box.
View 3 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Engine Noise / Right Side Cylinder Head Began Running Very Loud
To make a long story short, after replacing the timing chains, guides, and tensioners, the right side cylinder head began running very loud. Think of the usual chatter associated with these engines and multiply it. It was constant, from start up to shut down, and it increased with rpm. Thought at first it may be caused by debris in the oil clogging the lifter(s). After changing the oil multiple times along with different additives and driving roughly 600 miles, the noise persisted. Taking a look down the oil filler tube with a flashlight and with the engine running, the head looked dry. Safe to say at this point I was starving the head of oil.
Removed the valve cover. Removed the rearmost camshaft cap. Sure enough, the oil passage was completely blocked. Inspected everything and there was signs of running dry (minor discoloration, dried oil spots... but no real damage and no play anywhere. Put it all back together and the truck runs quieter than the day a bought it.
Here's the camshaft cap:
This is exactly what it looked like after removal. The material blocking the passage is hard and bridle like plastic.
Ford Super Duty (1999-2016) :: 2000 F250 - Manual Transmission Noise When First Started
I am new to being an F250 owner. Just recently purchased a 2000 F250 SD 4x4 with the 5.4 and a 5 speed trans. Got a pretty good deal on it, because I knew some work had to be put into it, and do plan on dropping the trans. Currently, if the truck has been sitting for a little bit, not cool, but not running for a little bit, when I start it, whether it is in gear or in neutral, there is a noise coming from what seems to be the clutch area.
After a couple minutes of driving, this noise goes away and all sounds as it should. A little bit of researching turned up the possibility of the throw out bearing being bad, however, I found other posts online that doubt this. Another symptom that I assume is connected is that if I go to put it in reverse at 0mph from neutral, it grinds.
In order to go into reverse, I have to press in the clutch, put it in first, then put it in reverse, at which point it goes in no problem. I had already planned on replacing the clutch because it seems to me that would be the logical choice as to where the problem originates, so no issue there. But perhaps I'm wrong??
Ford Super Duty (1999-2016) :: 2000 F250 - Making Ticking / Knocking Noise
I have a 2000 F250 5.4 that has a ticking/knocking noise. After about 30-60 seconds of first starting the truck in the morning, the ticking/knocking noise appears. It sounds like its coming through the exhaust system and seems to be louder under the front passenger side wheel well. When I rev the engine up, it seems to go away. Does this engine have a cam phaser? Could it be timing chain slap?
View 11 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Installed Clutch Now Grinding Noise?
2000 Ford F250 crew cab 4 x 4 with 7.3. 6 speed transmission.
I just had a new clutch installed and now I am have a grinding noise when putting it into 1st gear and when I change from granny to first it will grind also. I did not have this issue before having the clutch replaced.
I have also just had a new hydraulic clutch kit installed.
Ford Super Duty (1999-2016) :: 2004 F250 Keeps Blowing Fuse 23 When Hit Bumps
2004 5.4L F-250 ... it's a one owner truck I bought brand new in 2003 and only has 50,000 miles on it.
I have the 2V 5.4 engine no tuner or chip. 4x4 with 4" lift and 35's and I changed the rear to 4.88's. I love the truck but my problem is when I hit a large bump or drive too fast on a dirt road the fuse#23 that controls the PCM will blow. Consistently. I have to keep a box of 20 amp fuses handy. I have a 2 post lift in my shop and have scoured over every wire that is connected to the fuse. The EVAP solenoid, AC Clutch, Transmission solenoids and the O2 sensors. I only have 2 sensors I could find one on each side of the headers.
I couldn't find any rubbing wires or exposed wires. I am at a loss. It only happens when I hit a large bump. Could it be the Torque Converter Clutch Solenoid?
My brother in law is a mechanic and he brought over the diagnostic computer and when it blew while hooked up he seemed to think it was the TCC solenoid because when it engages the chart shows it angling up but when it disengages it drops off straight like it should. My truck seems to run fine when the fuse isn't blown, but when it blows it goes into a limp mode with the tranny stuck in 3rd or 4th gear and I have to drive it home in 1st.
Ford Super Duty (1999-2016) :: 2001 F250 4x4 - Loud Whining Noise Found / Wheel Seal Rubbing On Inner Part Of Bearing
I have a really loud whining kind of noise found that its the wheel seal rubbing on the inner part of the wheel bearing. I was just curious if its safe to drive with the spindle removed from the axle?
View 5 Replies