Ford Ranger / B-Series :: 2003 - Lean Codes / Jerking At Highway Speeds
I've got a 2003 Ranger 2.3L DOHC, 5 speed, 2WD. It has a check engine light with codes :
P0316-Engine Misfire Detected On Startup
P0704-Clutch Switch Input Circuit Fault
P2195-O2 Sensor Excess Lean Signal Bank 1-Sensor 1
P0171-System Too Lean (Bank 1)
The truck runs fine when coasting or accelerating but when holding a steady light throttle to maintain speed the truck starts bucking and jerking. It's doesn't feel like a misfire, more like a fuel cut out condition. When this happens and you come to a stop, you can smell that the exhaust is very rich coming out of the tailpipe. I've already replaced the upstream O2 sensor and I did a tune up about 15k ago. I'm thinking fuel pump or fuel pressure regulator. I doubt if this is related, but on start up (more so on a cold start up) the A/C compressor clutch kicks in and out 3-5 times and makes a terrible racket.
Camry 2012+ :: Passenger Window Goes Up / Down Considerably Slower Than Other 3
Planning to take the 14.5 Camry in later next week. I've noticed the passenger window goes up/down considerably slower than the other 3. I know it's not specific to the passenger window, but have you guys experienced any given window quite slower than the rest? I don't think it's wear and tear since I have no passengers 85% of the time. Wonder if warranty still covers it within 2 years..
View 1 RepliesFord Ranger / B-Series :: Codes P2195 And P0171 - Idle Gets Slower Till It Lopes
I have a P2195 and P0171 ... 2006 Ranger 2.3 ... Drives fine but at idle..idle gets slower till it lopes. Changed O2 sensor,Cleaned air flow sensor,changed PCV valve, Can't find any leaks, could it be EGR...how do I check it ?
View 1 RepliesFord Ranger / B-Series :: 1983 - Poor Fuel Mileage?
I recently bought a 1983 Ford Ranger Diesel pickup truck (2.2L Mazda engine, manual transmission). The dealer said to expect a little above 30 mpg on fuel mileage but the two fill-ups I've done show an average fuel mileage of 22 mpg. About half of these are highway miles.
I thought diesels are supposed to have good mileage. Is this typical for my year and model truck? Is there any way to increase the mileage? I just replaced the air and fuel filters and also changed the oil and oil filters.
Ford Ranger / B-Series :: Poor Idle - Codes P0171 And P0301 - PCV Valve Elbow?
2001 Ranger 4-cylinder 2.5L engine, 180K miles. I have been getting PO301 for months now, on and off so it's probably not related to this one.
It started idling awfully a week ago but does not die. Some vacuum problem. I heard the PCV valve elbow is the likely problem but where it is located? A pic or a diagram would be really useful, I did a search but keep getting 4L engine and other makes/years.
It's currently throwing P0171 code. A code P0171 may mean that one or more of the following has happened:
The MAF (Mass Air Flow) Sensor is dirty or faulty
Note: The use of "oiled" air filters may cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.
There could be a vacuum leak downstream of the MAF sensor
Possible cracked vacuum or PCV line/connection
Faulty or stuck open PCV valve
Failed or faulty oxygen sensor (bank 1, sensor 1)
Sticking/plugged or failed fuel injector
Low fuel pressure (possible plugged/dirty fuel filter!)
Exhaust leak between engine and first oxygen sensor
Ford Ranger / B-Series :: Poor Brakes At Low Speed And Sucking Noise From Pedal To Booster Connection
Odd thing on the 97' Ranger that showed up today. I was backing out of the spot at the local Shell station, (on an incline) and the pedal went to the floor. Never happened before. I pumped the brakes a few times, and they came back. On down the street, slowing for the stop sign, pedal went to the floor again.
Not throwing codes, fluid levels are good, only seems to happen at lower speeds/idle. Sometimes pumping brings the brakes back, sometimes they come back all of a sudden.
I can hear a "sucking" kind of noise coming from where the pedal connects to the booster, up under the dash. I looked at it, and nothing *appears* to be broken.
It almost feels like the pads are against the discs, and the pistons/calipers have to reach for them before the brakes apply. (If that makes any sense)
There should be about 50% of life left on the pads, but i haven't pulled the fronts wheels yet to look.
Ford Ranger / B-Series :: 1992 - No AC And Power Steering / Poor Clutch Disengagement Resulting Hard Shifting
1992 Ford Ranger 4x2 with 2.3L engine and 5 speed manual transmission. 135,000 miles, no AC and no power steering. I am having poor clutch disengagement and resulting hard shifting. The shop added a little fluid to the reservoir last oil change and it is still looking full. I always park on concrete and never see any leaking. I don't know what may have been done before as I haven't had the pickup all that long. Where should I start? Is there probably internal bypass leaking in the hydraulic clutch as there seems to be no external leaking?
View 4 RepliesFord - Ranger :: 1994 V6 - Clicking Noises When Hauling A Load At Highway Speeds
My 94 ranger 4.0 v-6 makes clicking noises when hauling a load at highway speeds. How do i correct this?
View 4 RepliesSanta FE SM (2001-06) :: Shudder During Acceleration At Highway Speeds
My '04 Santa Fe (135K miles) has been doing this for a little while.
Between 65 - 75 MPH on the highway, under acceleration, I experience what I can only describe as a "shudder".
I don't believe it's a wheel balance issue, because if I'm coasting or maintaining that speed everything is stable.
Ford Ranger / B-Series :: O/D Shifting In And Out At Speeds Over 50 MPH
My o/d has started shifting in and out at speeds over 50mph. It looks like it happens for the tiniest changes in engine loading. A windy day plays havoc and mild inclines. Sometimes the o/d light starts blinking until I switch off then operates normally. Extended warm-up driving seems to work. I've been told the rear axle speed sensor may be going bad but I have no confidence in the advice. I am driving an '02 ranger, 3L flex fuel, 2wd and just went over 100k. The atf is at the correct level but the fluid needs changing in my opinion. There are no engine codes.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Occasional Miss At Highway Speeds / Bucking And Jerking During Even Gentle Acceleration
165k miles 4x4 6 speed, bone stock unmolested
Slowly progressing problem over 6 months. Occasional miss at highway speeds uphill has progressed to bucking and jerking during even gentle acceleration attempts.
I hadn't got my cam sensor recall done but no change after that procedure completed yesterday. Oil recently changed as well.
I have a torque pro but it never finds any fault codes even though 'service engine' light comes on sporadically. I'm not sure I'm operating it properly but it at least reads rpm when its running.
I'm contemplating the hutch mod but I'd like to have an official diagnosis beforehand if its possible in my case.
Ford Ranger / B-Series :: 1997 - Randomly Jerks On Highway?
I got a 1997 Ford Ranger 2.5L that randomly jerks on the highway and I can't figure out what the problem is. This morning I had a 3 hour drive and it was fine on the first hour and then the last 2 hours it will randomly jerk on the highway and then be find for a little bit and then do it again. I don't know what the issue is? I did scan my car this morning and did have two code P0141 and P0113 not sure if these would have anything to do with it or not. Also my speedometer is hit or miss when it works, other than that everything else is fine on the car no check engine light or anything like that.
View 6 RepliesFord Ranger / B-Series :: 2000 - Sputtered Out On Highway And Won't Restart
About a month and a half ago I was doing 70mph down the highway and the truck began to lean out sputtering and sounding like fuel was not getting there, when I pulled over on the side of the highway because it killed itself and then the car would not start I noticed the ox sensor for the 3rd cat was ripped out from being caught on the driveline, I removed ox sensor and car still wouldn't start. I took the truck to my buddies shop and after a new ox sensor was installed with some effort the truck started 30minutes later, I did not think this was reason for the truck to not start but after a day it was running like a top again, little did I know. Last week driving down the highway ironically in the same spot as before the truck did the same thing sputtered to a stop and would not restart.
Side Note: on both of these occasions after the truck would sit for a day it would start run for about 5 seconds and die???? So I had it towed home again and began reading FTE, I saw posts about fuel pressure and spark and P0176 code for Flex Fuel, Inertia Switch and so on.
So I started with Fuses they all look good then the most popular post and 2 of the codes were P0176 and P0177 for flex Fuel they read OBD II flex fuel wont start....Another code was for EVAP and 3 codes for heater bank(it turned out to be a fuse but is or could something trip this to send the car down this path?
I Then figured I would try the Fuel Filter..This did not work.
2nd I tried was Fuel pump pressure is good based off others posts.
So I bought the Flex Fuel Replicator that eliminates the need for the flex fuel sensor, from the guy in Portland, well this didn't work either. Next I went to spark checked all plugs they smelled like gas and were slightly fouled I had just replaced these about a year ago but hell why not? so I replaced and got nothing still also checked the oil had some gas smell to it but my buddy said this was normal with trying to get it to turn over without success.
Checked inertia cut off it was normal, checked fuses they were good(except heater which has been replaced). Now I am stuck...
Ford Ranger / B-Series :: 3.0 Engine Stumble When Cruising On Highway
OK,it's a Taurus but it's the 3.0 Vulcan.On the highway crusing easy,now and then I'll get a stumble.It's like the key is turned off and back on.The tach stays steady but the car stumbles like the key was cycled quickly.I had to put a fuel pump in it a few weeks ago and now it is starting every time but this stumble has me stumped.
View 5 RepliesFord Ranger / B-Series :: 2005 - Squeaks At Low Speeds?
My ranger started to squeak at low speeds a few months ago (when it was pretty cold) and still does it in the mornings when I first start driving it. It squeaks from around 2mph up to 25-30 and then it seems to go away (or I can't hear it anymore cause of other noises haha). It is from underneath the truck somewhere, and not related to clutch or brakes. It seems to do it in the mornings only (or when it's cold) and increases in frequency when your speed increases. Not engine related at all.
My first thought was U joints or the driveshaft rubbing, since the squeaking was directly related to how fast you were moving and clutch in/out and brakes didn't change the noise at all. I couldn't find anything rubbing on the driveshaft.
Changed the U-joints since they were kinda old, but this didn't fix the issue. Next I pulled the rear brakes and checked all the springs and such, nothing I could see was wrong. Greased up the shoe contact points and put it all back together.
It was still squeaking, so I checked the wheel bearings for play and spun them while each corner was jacked up, the bearings seemed fine and didn't make any noise when I spun each tire. I have transmission and rear differential fluid.
I've checked all of the stuff I can think of and am kind of at a loss as to the next step. I guess the things it could possibly be are transmission bearings (input/output, since those spin all the time right?), pinion bearings or rear end bearings, wheel bearings (even though i've checked them), or ??
I've driven a chevy with bad bearings in the rear end, and this doesn't sound like that. The chevy sounded like a dull roar at speed, and kinda droned a bunch. this is a very distinct squeaking sound, very similar to a squeaking bearing on the idler pulley or something like that.
Ford Ranger / B-Series :: 2011 - ABS Engages At Low Speeds?
I have a 2001 Ranger XLT 4x4 with 38,000 miles. When I am at very low speeds (like 5 mph) and usually pulling into a parking spot, the ABS kicks on. I've heard it's the "hub" in my wheel but the dealer won't know which one to replace. Dealer said, take your hands off the wheel and see which way the truck pulls when the ABS is kicking on....well at 5 mph it doesn't pull. At $300 just for the part, I need to know which wheel it is!
Also a friend of mine had this happen to his Chevy Silverado and the replacement hub broke again so they just turned off the ABS....Is this OK to do if I don't want to fix this problem?
Ford Ranger / B-Series :: 2003 V6 Rough Idle / No Power On Highway
168K, to date, replaced
rear 2 cat's
Timing chain and gears
cam sync assem.
Plugs, wires, dis block,
Why.............. Read on
This 2003 ranger 3.0 v6, run very hard at idle, yet it runs and you can drive it around town, ""at"" low rpm, and no hills but it gets from point a to point b
I have no pre ingintion, but a plug that was only 60 days only was burnt out completely on 3rd cyl. bank 1 or as ford call it #3, i am telling you this thing seem like it running on 4 cyl,s kicking back and forth, and replacing everything above made no difference.
On the highway, as long as it is flat or down hill 75-80 mph, as soon as a hill or power to pass is needed it bogs down and slows it self to about 45 mph, I have been though everything i can think of and my next move to to start pulling heads, but i wanted to ask here first.
Ford Ranger / B-Series :: 2002 - No Power On Acceleration
02 Ranger with 3.0 Flex motor, 375K+ miles. Been chasing an issue for a while now, but am about at the end of my diagnosing capabilities. Issue started with a misfire on 5 and rough running engine with no codes showing up. Now the motor is getting worse.
Idle a little rough and no power when accelerating hard. The engine sounds like a popcorn popper under hard acceleration. Motor revs up to 4K but does not pull or shift gears until I let off the gas.
The code that initially showed up indicated a bad Camshaft Position Sensor. Changed that and the Sync assembly - as per instrucions, exactly positioned same as old one. New codes showed up - P1152, P0175, P0171. Cleaned the MAF, rail fuel pressure OK, can't find any vacuum leaks, replaced both upstream ox sensors, and changed #5 ,6 injectors.
Motor still runs the same - like crap, like a corn popper on acceleration, smooths out if only slightly accelerating, but stumbles n bumps on steady cruise speed over/around 60 mph - and no codes showing at present.
I really, really don't want, nor can I afford, to take it to the dealership, but I may be forced to if I can't figure this out sometime quite soon. I make my living with this truck so, no truck, no work till this issue is solved.
Ford Ranger / B-Series :: 1994 - Hesitates Under Acceleration
Having a slight issue with my ranger. So I bought this truck out of a junkyard about a month ago, its a 94 4x4 with a 4.0 and a five speed. When I bought the truck the motor was blown so a few weeks ago i replaced it with a 4.0 from an aerostar van I had laying around. Right after I changed it the truck was running good with no issues, until a few days ago going to work the truck started hesitating going up a hill. Now the truck does it all the time, sitting at idle the truck runs smooth as silk, at half throttle it does it the worst but when you mash the peddle to the floor it clears up and runs good.
So far I've replaced the plugs, wires, coil pack, mass air sensor, throttle position sensor, and the fuel pressure regulator to try and fix it but nothing has worked. I've checked the fuel pressure it has 30 at idle and 40 with the vacuum hose pulled off of the regulator, I even taped the gauge to the windshield and went for a ride and there was no drop in pressure when it started acting up. a few other things i have done were plugged all the vacuum ports to rule out a leak, reset the computer and checked for codes. the only code that came up was 522. So I think my next step is going to be buy new oxygen sensors ? But my question is wouldn't the check engine light come on if it was an oxygen sensor ?