Ford Ranger / B-Series :: AC Cycles Off And On
I need to change the AC relay. What is the location of the relay.
View 6 RepliesFord Ranger / B-Series :: 2003 Turns Over But Won't Crank After Fuel Pump Replaced
Just replaced fuel pump and now it turns over but won't crank. I have checked the fuel rail. Pressure is fine. Checked coil pack I'm getting spark. Still won't crank. Checked inertia switch it wasn't tripped. What next? 2003 Ranger edge...
View 1 RepliesFord Ranger / B-Series :: New Plugs Now Truck Running Rough
Although my lil' truck (2006 Ranger XLT, 2WD,with 4-cyl / 5spd, and 115K miles) has been running just fine since I bought it about a year & 5K miles ago, I suspected it still had its original spark plugs and I figured I should change them before problems arrived.
As I suspected, the plugs that I took out looked to be original. I measured their gap and they all had excessive plug gaps - around 0.052" gap. I installed the four new AUTOLITE APP104 (double platinum) and checked their gap, and they were a bit tight at 0.042". My book says they should be at 0.044" gap. But I installed them at 0.042 anyway, figuring they'll burn wider in time.
One by one, I smeared a small bit of never-seize on the plug threads & at the plug-to-cyl head tapered edge. I smeared a dab of Dielectric Grease around at the top of the plug to ease the plug wire re-install and hopefully calm any possible arching. The plug wires came off the plugs easy enough and went back on just as easy.
I hit the key and the engine fired right up. It idled rough as expected. However, it continued to idle rough and if I raised the RPM level, it would respond, but still ran rough. It is throwing a 'Check Engine Light' on the dash cluster now - whereas it wasn't prior to the new plugs.
Ford Ranger / B-Series :: 2004 - Changing Spark Plugs?
2004, 4L, sohc - Is there any issues or problems changing spark plugs?
View 4 RepliesFord Ranger / B-Series :: 2001 - Turns Over Great But Will Not Start After New Plugs And Wires
2001 Ford Ranger 4.0 - 250k miles had the original plugs and wires ....
First things first - I changed them one at a time and confirmed the truck started and ran after each one was changed. I changed all the plugs on the drivers side with no issue. 4,5,6 ... Then I changed plug 3, rear passenger side plug closet to the firewall.
Truck will not start, turns over great, but will not start. I have confirmed I am getting spark. No clue what could have changed, I just pulled out the old plug and wire put in a new one and it wouldn't start.
My father-in-law said if you have spark check fuel. I recall seeing a post about someone breaking a cable for the coil pack but i have checked and i see nothing broken.
Celica :: 1992 GTS Won't Start At All - Fuel Smell On Plugs
1992 GTS ... Code 12 (ignition). My car started misfiring and now it won't start at all. Just checked all four cylinders for spark and they have spark. I can also see/smell fuel on plugs when I pulled them.
View 2 RepliesFord Ranger / B-Series :: 1987 - No Power After Water Line Broke On Left Side Near Spark Plugs
I have a 1987 Ford Ranger 2.3L, it's the truck I learned to drive in (stick at 13yo) and the 1st car I crashed too... So now this baby is almost 30 years old and recently had a minor restoration...
Engine was pulled out and all gaskets were changed, spark plugs, wire... All that stuff... It has been running pretty good, however last week a water line broke on the Left side near the spark plugs (if you are looking at the truck)
Since then It has absolutely Zero power. The slightest hill and even when pedal to the floor will lose power. Yesterday went from the start of a hill at 60mph in 4th to 20mph in 2nd because it didn't have the guts to go 1/3 mile uphill... I checked everything I could, and my brother took it to the exhaust guy who made a small hole on the Catalytic Converter and said it was good, but he could tell it was running too rich...
I replaced some of the vacuum lines last night, I found a lose one on the fuel pressure regulator (I think that's what it is, Its towards the engine firewall on top).
Idles beautifully, drives great, no rough shifting, pinging or knocking, no misfires. So that's what has me stumped... Runs great but just no power... Also before water line broke it was running fine with power...
1987 Ford Ranger
2.3L FI
5sp manual, Rwd
Ford Ranger / B-Series :: 1990 - Broken Fuel Line At Fuel Pressure Regulator?
I have a 1990 Ranger with a 4.0L that I just changer the intake gasket on. I broke the fuel line at the Fuel Pressure Regulator. Cant seem to find one anywhere. It is a nylon inside/rubber outside with a cloth mesh and quick connect fitting line. Where to get one? Can I hose clamp it the FPR by cutting off the connector that broke?
View 1 RepliesFord Ranger / B-Series :: 1996 - Won't Start And Crank Even?
I have a 1996 Mazda B2300 & I heard that it is similar to the Ford Ranger.
Well the thing won't crank or start.
This is what I have done so far. I wanted to put a RPM meter on it. I followed YouTube videos on how to do it. I cut the Tan wire w. the yellow stripes & try to connect the wire to thr RPM meter. Then it won't start soo idk what to do. I also took put the PCM too. (I was looking for the wire) Now be honest, I talked to a mechanic, he said thag I might have blown my PCM or Blown another fuse. But when i put the key in to crank, it won't start ot click at all. The lights come on & it wants to start but won't start.
Then my mechanic tried to start it by the... Idk what it is called but you can start it & it wont evet start. It will crank like crazy but will not start at all.
Ford Ranger / B-Series :: 1994 4.0 Sometimes Will Crank And Not Start
94 Ranger, 4.0, Automatic, 280k miles. Normally starts and always runs fine. Sometimes will crank and not start. Fuel pump replaced Feb. 2015 and again Dec. 2016. Have had it towed 3 times. Always starts when it gets to the mechanic. Sort of reminds me of vapor lock on the old cars with carbs, because if it sits long enough after not starting, it will start, no problem. Never died out or even coughed when running and plenty of power. When I take off the gas cap, it sucks in air like a whale. Twice I did that and it will not start right away, but if it sits for an hour or so, it starts no problem. Just bought a new gas cap 10 minutes ago and looked in a Haynes manual and a " gas tank vapor valve assembly" is mentioned. I don't want to change parts just to see what happens. Mechanics say there are no codes shown.
View 1 RepliesFord Ranger / B-Series :: 1988 XLT V6 Won't Start Just Crank
I have tried about everything i know about cars on this truck!! It ran great when I got it until a head gasket got blown so I tore into it and replaced them both torqued heads to specs. Made sure valves wasn't to tight. Distributor is in correct spot timing is correct had ignition module tested good!!! Coil tested good replaced both fuel pumps and put new tank and sending unit in the truck b/c it needed it new fuel filter replaced return line firing order is correct 1 4 2 5 3 6 it is getting fire it will crank and crank sometimes act like it is going to start then not also I can get it to run for about 3 sec on 3 or 2 cylinders it seems to have plenty of compression as well!! only thing really I can think of that could be wrong is computer? Also one last detail tried pull starting it as well still wouldn't go.... V6 2.9L...
View 9 RepliesFord Ranger / B-Series :: 2001 V6 2WD Won't Even Crank When Turn The Key
It's a 01 Ranger 3.0 V6 5 spd 2wd. He drove home from work then the next morning wouldn't crank over. Turn the key and it doesn't even attempt to crank. All dash lights, headlights, etc come on. Battery is good. Took starter out and tested at parts store. Tested good. Clutch switch was good. Replaced ignition switch with no change. If I jump the solenoid on the starter it will turn the engine over. When turning the key I can hear the starter relay in the fuse block under the hood clicking. All fuses were good. I found the main engine ground wasn't hooked up to anything. I hooked it back up and still nothing. All battery connections were good but cleaned them anyway. Not really sure where to go from here.
View 6 RepliesFord Ranger / B-Series :: 1991 - Won't Start But Crank Great?
Getting the Banana ready for it's smog test appt at the shop last night (it WAS today) Check engine light had popped on and it had been starting to sputter and surge at the idle occasionally for the last few days so I took a look at the MAF and saw dirty wires. Aha I can fix that, a couple squirts of MAF cleaner, plug it back in and voila! No more light, the Banana ran down the road around the block, over the hill and through the dale like a champ. I shut her down and call it a night.
This morning, hop in and fire the Banana up like usual and all I get is a nice peppy crank over. The Banana has had a bunch (pun intended) of new parts throw at her recently... new battery, starter solenoid, plugs and fuel pump relay and fuel filter. All within the last couple of months.
Out of complete disbelief, I ground on the ignition for a little while and she finally kicked over and sputtered to life. I let her idle a couple of minutes and things seemed fine so off we go. I make it about a block before the Banana starts hiccuping and bucking like something possessed and dies.... kaput.
The Banana has a 3.0, manual transmission and at least half a tank of fuel. Long story short and a tow truck ride home again, half a day trying unsuccessfully to pull a code, any code.... nothing. She will half-heartedly cough and spastically run with ether shots and near as I can tell I'm not getting fuel to the fuel rail relief port. I'm really hoping there is some way to diagnose a faulty fuel pump without having to drop the tank and fish the damn thing out.
I'm not hearing it run when the ignition is turned on but then again I don't think I've ever heard it run. Any other things to try before I replace the pump itself???
Ford Ranger / B-Series :: 2005 XLT 4.0 - Intermittent No Crank And No Start
I have a 2005 Ranger 4x4 4.0 automatic with an intermittent no crank, no start issue, So the problem has been getting worse over time This time when it wont start, all of the lights work, the radio, the fan, etc. They are all bright and functioning.
The battery is brand new and showing 12.9v at rest. (Yes, I have tried to jump it and charge it to be sure). However, The gauges are not functioning when the key is turned. I have no click, the lights don't dim, nothing happens when I turn the key.
Another neat point, if I turn on a directional with the key on, the relay clicks so rapidly that it won't even flash the lights. I am assuming that it is a ground someplace, but I dont even know where to start on this truck.
Ford Ranger / B-Series :: 2000 - Won't Start Intermittently Only Crank?
I have 2000 Ranger 4.0L 4wd, 5sp ...
Just in the last month or so as out temps have been dropping off I've been having troubles getting her started. It happens both when the engine is cold, ie first start of the day, and after starting when warm. It did it a couple times last spring, but then all summer and fall I didn't have any problems (warm outside air temps) but, now its happening again. I'd say any time the Outside air temp is 40F or less, I am worried it won't start. IF i get her to start, everything else is just fine and she runs like a top. Here are the symptoms and what I've done so far.
When I crank I will get a couple cylinders to fire for a second or two then it falters out behaving like fuel starvation. Then I crank again right away and nothing fires... just cranking over and over. If i wait a minute and crank again same symptoms or it will fire right up. Baffling!
I thought Idle Air Control valve and sticking fuel pump relay, so I threw new parts on, but no fix.
About 75% of the time if I turn the key on, hear the fuel pump running, turn key off and on, hear the pump again x3 and then attempt the start it is successful.
Unfortunately, I don't have a code reader, or fuel pressure test equipment. The check engine light is NOT ever on. DO I HAVE A FALTERING FUEL PUMP??? I've heard thats tough to change out.
Ford Ranger / B-Series :: 2001 V6 - No Crank / No Start When Turn The Key
2001 Ranger 3L v6 auto, 186k miles. Never had a problem. One day last month I park it at home. 10 minutes later I need to make a quick trip . Get in, turn key, absolutely nothing happens. Replaced the battery, starter/solenoid, and ignition switch (not the key cylinder lock, but the white box inside the dash below and to the left of the steering wheel...has lots of wires going into and out of it,...turning the key slides a little metal pin inside it up and down). All fuses and relays are good, neutral safety switch is good. Key lock cylinder is mechanically working properly. Engine is not headlights, interior lights, wipers, radio, etc all work fine. Theft light is not blinking rapidly. Headlights do not dim when ignition key is turned. Where do I go from here?
View 2 RepliesFord Ranger / B-Series :: 1999 - Crank But No Start / 3200 Rpm At Idle
1999 mazda B4000 4WD 178000 miles 5 speed manual, I've been having a crank no start problem but after a few tries it would start, a week or so ago it was really cold (23) it wouldn't start so I opened the air box and shot it with starting fluid it took about 5 long sprays but it started.
It ran up op 3200 rpms and won't go back down, took it to my shade tree mech. he hooked it up to the diagnose thing it showed no codes, he poured water over the motor it different places and toward the back it idled down for a second so he says "blown intake gasket' so we replace upper and lower and sure enough we could see where there was a bad spot on the upper and a cleaner spot on the port.
That was not the problem it still idles at 3200, I mean wide open screaming, could the starting fluid have done something? Now he says "blown head gasket" I never had any idle problems before matter a fact besides the hard starting problem that started it was running just fine, what happened?
Ford Ranger / B-Series :: 1996 - Crank 4 To 5 Times To Start Intermittently?
i have a 96 ranger with a 2.3l engine sometimes it will start right up and sometimes it has to crank 4 or 5 times to start i just gave it a tuneup and changed the oil and filter. should i run sea foam through the oil system,it sat for about seven years and i need to convert the idiot gauge to a real gauge.
View 2 RepliesFord Ranger / B-Series :: 1998 3.0L - No Crank No Start - Only One Click When Turn The Key
1998 Ranger, 3.0 liter manual transmission. The vehicle recently has had the engine replaced. Still a 3.0 Liter, but possibly is from a 1995 or 1996 Ranger. Replacement motor from a wrecking yard, appears to have been sitting for quite some time prior to purchasing. I had a friend change the motor out after getting the vehicle a few weeks ago.
Ranger drove fine for a week, but this morning it wouldn't start. One click is all it would give when you turned the key. Thinking the culprit was the all in one starter/solenoid, I replaced it with a new one this morning. Now the solenoid will click continuously when the key is turned, starter still will not rotate then engine.
Battery tests good - 12.4 volts; connections appeared fairly corroded.
Here is what I have done:
- Clipped off the first half inch of corroded terminal leads, replaced both sides with new battery connectors and wire brushed connections off at battery and starter.
- Replaced Starter
- With "S" connector disconnected, attempted to bypass starter connections and short terminals to see if a faulty clutch position sensor was to blame; shorting did not produce anything other than turning the key did.
- Paralleled an additional cable from battery to starter terminal to see if corroded wire connections were to blame; still just clicked repeatedly when attempting to start.
Crankshaft does rotate manually, does not appear to be seized up. Unsure of what else to check for. Not confident in friend's engine installation abilities, he may have screwed up something I'm not thinking of. On the other hand, I don't believe I would have been capable of swapping out the motor myself.