Ford Ranger / B-Series :: 2000 - Constant Leak From Gasket Between Thermostat Body And Engine?
I have a real problem with 2000 Ranger, after changing the upper radiator hose and thermostat, I now have a pretty constant leak from the gasket between the thermostat body and engine. Appears to be something that is triggered by the thermostat opening, so whatever the leak, the thermostat is blocking it.
I've changed the gasket, cleaned the mounting surface as good as I could. Tried re-torquing the bolts, but on that score - what is the torque specs for the 2000 3.0 liter Ranger?
But ultimately, what the heck is wrong here? This should be a pretty brainless operation really. Am I tightening the connection too much and cracking the gasket? I guess that has just occurred to me, although the gasket is not as stiff as a typical fiber gasket is.
Ford Ranger / B-Series :: 1991 - Temperature Gauge Not Showing Constant Reading?
1991 Ranger STX, 4.0. Had a leak from the rubber seal on the thermostat. Changed the thermostat (stat 195) and seal. Now my temperature gauge is not showing a constant reading, goes to half way and when the thermo opens the gauge falls down to a quarter. The gauge is cycling this way every time the thermo opens.
View 2 RepliesFord Ranger / B-Series :: Constant Thud Coming From Front Driver Side While Driving
When driving down the road, there is a constant "thud thud thud" coming from the front driver's side of my 99 Ranger. I've been looking online for about two hours now, going back and forth to my truck to see if I can figure out the problem. All I've come up with is that it's the sway bar links. they're both disconnected, and I'm going to replace them anyway, but would that cause the constant thudding?
View 3 RepliesFord Ranger / B-Series :: 1990 XLT V6 - Loud Constant Whistle Sound On Driver Side
So I have a 1990 Ranger XLT 4x4, 2.9 v6. My issue is I am getting a loud constant whistle sound on the drivers side, just in front of the rear tire. It is not from the tire and it is a whistle not a whine. The truck is all stock nothing special. I do not have an exhaust anymore only a cat. Anyways the sound is constant an does not get louder or quieter while moving or in neutral it just stays the same. It just started in the last few days. Also the truck is a Manual.
View 3 RepliesAccent MC (2006-11) :: Tick Tick Noise In Front Of Driver Seat While Waiting At Traffic Light
I just recently started driving... with a second hand hyundai accent. Whenever i stop at traffic light with engine on, i hear tick tick noise (probs from engine?). it seems to be coming from front of the driver seat. When I start at the beginning, I do not hear any noise and also when i am driving i do not hear any noise or lets say nothing audible like this. Its only when i stop my car and while i am waiting, i hear this tick tick noise(very clear and audible).
Is it engine metallic part making sound when cooling down? When I start my car I see symbol for low oil pressure, batter life, check engine, but as soon the engine starts these symbol disappear which I think is normal behaviour.
Ford Ranger / B-Series :: 3.0 VS 4.0 Engine?
Opinions welcomed...thinking of taking a gamble on an '04 with 248k miles on it.....not sure what engine is in it.
View 14 RepliesFord Ranger / B-Series :: 2004 - Engine 3.0 Or 4.0?
thinking of taking a gamble on an '04 with 248k miles on it.....not sure what engine is in it.
View 11 RepliesFord Ranger / B-Series :: Top End Engine Cleaner
Does running a can of top end cleaner through your engine like Seafoam foul your oxygen sensors? should they be removed beforehand?
View 3 RepliesFord Ranger / B-Series :: 1986 - Engine Won't Firing
i have a 1986 ford ranger with a bored out 2.9 v6 that is not getting spark sent to the spark plugs disrtibutor has been changed along with spark plug wires any clue what the problem is
View 1 RepliesFord Ranger / B-Series :: 1986 - Gas Will Not Keep Engine Running
1986 Ford Ranger / 2.3 EFI / 140 CID OHC /4-Cyl/5 speed
So the last time I was here, I was having doggy issues which I thought were fuel related. I'm still having issues, although it appeared to cleared up a bit.
When I start the engine, it cranks over, I'd give it some gas, it would rev up, then suddenly die, no matter if I pressed down on the gas pedal or not. After two or three times doing this, it would turn over and maintain a steady idle, then off I go.........
The problem now? Well, late today I tried to get it going, and after about 15 times, I gave up. It would not stay idling, it would crank over then die. I did not want to ruin the starter. It seems the gas pedal is worthless after the engine decides to conk out, and no matter how many times I step on the gas pedal, nothing happens.
Has been replaced within the last few months:
Fuel filter regulator,
Inline fuel filter,
Cap and rotor,
Lucas fuel injector cleaner,
ECC computer, and Fuel relay switches, (multi-function relay/connector switch)
Air Control Valve - Removed and cleaned.
Checked all vacuum hoses.
Has not been replaced:
Map Sensor, (was told it's located on Pass. fender wall, but can't find it, according to the manual)
EGR Valve and sensor,
Throttle Position Sensor,
EVP sensor,
Spark plugs, (two years ago)
Plug wires, (two years ago)
Ignition control module, (replaced about six years, or more)
With trying to keep the gas going to turn it over, it does not, so to me, it seems to be more of a fuel problem than electrical, but I'm no mechanic.
Ford Ranger / B-Series :: Engine Was Not Revving Up When Stepped On The Gas
I have a 91 ranger with the 3.0 engine. Recently the engine was not reving up when i stepped on the gas. But, it kept running and i got home. Then one day it just wouldn't start after i just shut it off. I've changed the distributor cap and rotor,fuel pump and filter.I have spark to all 6 plugs and good fuel pressure to the fuel rail. I'm leaning toward the timing. Last night I found the harmonic balancer will just spin freely. Will this stop it from firing?If it is the timing, how do I find tdc and where is the # 1 firing position on the distributor cap(no markings)?
View 14 RepliesFord Ranger / B-Series :: 2004 - A/C Won't Kick On Until Engine Is Hot
It started doing this fairly recently - no work has been performed - it just decided to not work right one day... The A/C compressor will not engage until after the engine is hot - the idiot gauge on the dash has to be firmly in the middle. After it engages, though, hoo boy does it blow cold - which is great, except I didn't used to have to wait as long to get cold air... It does cycle.
I thought, okay - low coolant - I get one of those refill bottles of r134a (w/ "conditioners" and whatnot) with an attached gauge at walmart and pump it into the truck - no change. Gauge was cheesy - told myself to get a better one.
I wait a while and get another bottle of refill r134a - one with a better gauge on it - and try again. Truck doesn't want any more - I may have overfilled, but there's no change - before the compressor kicks in, the gauge reads in the red - overcharge - but once the compressor kicks in, it drops and starts reading in the green and, when I checked per ambient temp, it was a bit in the high-end of the green for that temp, but was fine. I have no way of checking the high-pressure port.
Is there a temp switch of some kind on this system? I don't think it's low on r134a, but something is keeping the compressor from kicking on like it used to.
Ford Ranger / B-Series :: Engine Does Not Start Without Being Primed
Engine doesn't want to start without being primed once started ideals real good but still sometimes Bogs out on acceleration.
View 3 RepliesFord Ranger / B-Series :: Engine Light Comes On For A Few Days Then Goes Off?
I have an intermittent problem with the check engine light. While driving in town once in a while the truck runs rough for just a short time. Then the check engine light comes on for a few days then goes off. The truck runs just fine after the rough 2 minutes but the light stays on. I checked the gas cap and it's ok. I changed gas stations but no difference. Sometimes it happens then doesn't happen for another 2 weeks.
View 4 RepliesFord Ranger / B-Series :: Running The Engine For AC - ABS Light Came On
So I'm sitting in my 99 2.5L at work while we are empty, running the engine for A/C because it's quite hot out. The truck was running for a half an hour or so, not moving, and I look up from my phone at my dash, to see a brand new ABS light on....
So I've pulled out my handy code reader, but no ABS codes have arrived. Maybe my reader can't read it, or maybe I need to drive. But what could this be? And is it safe to drive the truck home tonight? Pedal pressure still feels normal.
Ford Ranger / B-Series :: Engine Hesitates - Got 157 And 158 MAF Sensor Fault?
Problem: engine surging/hesitation, from idle to highway speeds. It will start and run fine, just hesitates/surges when gas is applied.
Before I pulled the codes, I tried seafoam in the gas tank, cleaned MAF sensor, cleaned throttle body, checked air filter, changed fuel filter, pulled/cleaned plugs, nothing worked.
Then today I finally used a scanner and pulled codes (my CEL doesn't work) and I got 157 and 158 MAF sensor fault, high and low voltage. I am reading about 6v on the C and D terminals of the MAF, I know that is much higher than normal, but what does that tell me? Why both high and low voltage readings? Just a bad sensor, or wherever that voltage comes from, ECM?
I also pulled 189 HEGO H02S sensor fault, unable to switch/lean during part throttle. What does that mean, just a bad O2 sensor?
Last I pulled a 542, fuel pump secondary circuit fault. Does that mean the fuel pump is bad or going bad?
More importantly, what should I troubleshoot first, would any of these codes cause my problem?
Ford Ranger / B-Series :: 1994 - Engine Cranks But Won't Start
My kid is using my 94 Ranger with 215,000 miles. It quit while he was on his way to work. Engine cranks but won't start.
Fuel pressure at rail was 12 psi (Key on eng. off). I replaced fuel pump. Pressure at rail up to 20 psi. Still cranks, no start.
I replaced fuel filter. Pressure at rail up to 30 psi. Still cranks, no start.
Replaced distributor cap/rotor and plugs. I have spark at plugs.
Chiltons from 1994 doesn't list a rail fuel pressure. I see new fuel pressure regulators are set at 41 psi. I pulled mine and hooked air to it. It (FPR) cracks at 37 psi. I have lots of flow returning to tank, so I assume the fuel system is working correctly. I've never replaced the timing chain/sprockets. Distributor rotor spins during engine cranking. When I rotate the crank pulley to 0 Top Dead Center the rotor is pointing to #1 on the distributor, so I don't think the timing chain has skipped a tooth on the sprocket??????
Ford Ranger / B-Series :: 1998 - Rough / Surging Engine
Throwing codes ... p0136, p1131, p1151 acts like it going to just stop then will take off, at a stop light it will sound like it has a large cam in it... It is a 1998 4.0 V6 automatic tranny.
View 1 RepliesFord Ranger / B-Series :: 1987 - Engine Dies While Driving
Recently, today in my 87 Ranger suddenly the engine dies and all electronics in the cab fail.
I noticed under the hood that the fusible link connected to the battery and an orange and black wire was smoking. Tracing this line i found that it leads to the ignition switch, as well as some other places.
There is another fusible link and the junction between the yellow ignition wire and the orange and black wire from the battery. This fusible link also was failed.
I'm planning on replacing the fusible links tomorrow but in case that does not fix it, where to look next.
The problem only occurs when the key is in the ON position. I'm thinking maybe I could do some tests with a multimeter on the ignition switch but am not sure of the details of what I should test for.
Summary: Fusible Links C, and E burn out when the ignition is in the ON position.