Ford Ranger / B-Series :: Vacuum Lines Bad On Driver Side / Actuators Won't Disengage Properly
I noticed that one of my vacuum lines was bad on the driver's side. I've done a lot of reading on the 4WD systems and frankly I'm confused now. My understanding is that when in 2WD the solenoid is open pulling a vacuum on the actuators (IWE) which keeps them disengaged. When you switch to 4WD the shift motor on the transfer case sends power to the front wheels and the solenoid turns off the vacuum which engages the actuators sending power to the wheels. Therefore if there is a vacuum leak the actuators won't disengage properly.
Through my trouble shooting I've determined that I think the solenoid is working properly because I'm getting a vacuum when in 2WD and no vacuum in 4WD. I believe that both actuators are engaged and working properly when in 4WD. However, I must not be getting a vacuum to the driver's side actuator (hub) because the line is totally busted up and can't possibly hold a vacuum. However the passenger side line looks good to me. Does this mean that I've been driving around in "3WD"??? I don't seem to have any problems when in 2WD turning (no tire skip or hop).
Ford Ranger / B-Series :: No Heat But Hoses Are Warm / Hot To The Firewall
1998 Ranger. I have no vacuum to the heater control valve (see link below) and hoses are warm/hot to the firewall. Where to start troubleshooting?
More Information for FOUR SEASONS 74809
Ford - Ranger :: 1997 - Vacuum Lines Coming Close To Hitting Serpentine Belt On The Front Of Engine
Ok, I have 1997 Ford Ranger, 4cyl, manual transmission, and more miles than I'd like to admit to.
Yesterday, I noticed that one of the vacuum lines was coming dangerously close to hitting the serpentine belt on the front of the engine. The clamp that normally holds the vacuum line in place rusted away a decade ago, so I decided to use some velcro ties to attach the line to the positive battery cable. I didn't twist or pull on the cable in any way and the vacuum line isn't applying any force to the cable.
I get in the truck a few hours later, hit the key and I get >click<, but nothing out of the starter. One click when the key is in the start position, nothing more (as opposed to click-click-click).
Not thinking about my repair earlier, I went down to Autozone and had them test the battery - 12.8V and 550CCA, no problem there.
So then, I thought well since the click is coming from the starter relay, maybe that's where the problem is. I read on another forum that sometimes the starter relay can be resurrected temporarily by hitting it with a hammer. Which I did. And it did work! Now the truck is starting up normally every time, but I'd like to replace whatever was bad.
My questions :
1. Did I prove anything by hitting the starter relay with a hammer and then starting the truck?
2. Should I still be looking at the battery cables?
3. Should I stop hitting random parts with a hammer and take this truck down to a real mechanic before I do serious damage?
Ford Ranger / B-Series :: 1988 - Rusted Rear Brake Lines
I am going to fail State safety inspection due to a problem with my brakes. Months ago when I was trying to get it through emissions testing the mechanics looked under the truck to see where the brakes were leaking. All they told me was the rear lines are rusted through and need replacing.
From my reading I believe the lines are 3/16" line and I think they go around the back of the fuel tank and up the frame rail. Correct?
My questions are, what length line do I need (I am not a hard-line expert, but I will try). I want to order some ss line so it won't rust through again. Is the system made of small sections threaded together? Or is it one long section? And what else would I need/want to replace along the way?
Ford Ranger / B-Series :: 1998 - Front Brake Lines Kink In Sharp Turns And Wear Out
98 Ranger Front brake lines Too short! they kink in sharp turns and wear out then start to seep then eventually leak and need replacement. Checked parts references and the lines have been considered stock. Not sure if I have a 1/2 year model.
View 1 RepliesFord Aerostar :: A/C Blowing Through Defrost Only - Where Are Vacuum Hoses
My 2005 Freestar (not the Freestyle) a/c is working properly except that it is only blowing through the defrost. I've read other posts about it being a leaking vacuum system on other ford vehicles that cause this problem.
1) I'd like to confirm that this Freestar a/c works on a vacuum system to open the a/c duct doors.
2) If it is, where are the vacuum hoses located? I'd like to check them to see if they are connected or if they have a hole.
Ford Ranger / B-Series :: Vacuum Hose Diagram?
Where I might be able to find a vacuum hose routing diagram for a 2.9? I have searched high and low but with no luck.
View 14 RepliesGolf IV R32 :: 3mm Or 4mm Vacuum Hoses?
I'm going to finally go through all the old rubber cloth shielded vacuum hoses and going to replace them with Samco silicone but not sure if I should use 3 or 4mm hose?
View 10 RepliesFord Ranger / B-Series :: Water Temp Sensor Leaking / Missing Vacuum Hose
Was fixing leaking water temp sensor today and noticed the nipple under oil fill cap didn't have hose on it. After further investigation I found open spot on air intake hose with nothing in it. Both places seem to have vacuum, what goes here. BTW it is a 1999 Ranger ext cab with 3.0 flex engine and auto trans. Will try to get picture n post also...
View 8 RepliesFord Ranger / B-Series :: 1994 - Sputtering Started Suddenly - Vacuum Leak Behind The Intake Manifold
I have a 94 ranger and all of a sudden it started sputtering, i can hear a vacuum leak behind the intake manifold found what appears to be a pcv valve not hooked up is that the way it's supposed to be?
View 2 RepliesGTI 337/20th Anniversary :: Broken Vacuum Hoses Causing Misfires
so i've had my 337 for a couple months now and when i first got it i found 2 broken vacuum hoses that were causing misfires. once i got those replaced my CEL went off and seemed to be running fine other than from time to time when i started it up my idle would be around 1.2k rpms and then after a couple miles itd settle down to 750-800 rpms but it wasn't rock solid, so obviously there is still something wrong.
on my drive home tonight from work i was in the mood for some spirited driving but when i'd hit the gas i could feel some hesitation through the powerband at wide open throttle. when i got home i turned it off, and started it back up to see if it was idling funny and when it ignited the rpms jumped to almost 2k and immediately fell back down to 1.2k.
My thoughts are its either a vacuum leak again, bad/dirty maf, dirty throttle body, or a boost leak.
Ford F-150 - 1997-2003 :: P0401 Code - Vacuum Lines?
So here's the background. I recently bought this truck. It's a 97 Ford f150 4x4 4.6l 99w vin code. Anyway Driving it home got a p0401. No problem. I Applied vacuum from other vacuum source to EGR engine stalls. So to me passages are clean in the throttle body. I checked to verify and indeed passages are clean. No while doing so I noticed no vacuum was making its way to the dose valve thing. Strange.... So took the line that runs to the passenger fender to dose off and it was impossible to blow air through.
So I cut out the clogged section found solder in the line. I filled the gap I now created using some 5/32 vacuum line reconnected to test and to my anvil still not vacuum. So I disconnected it again. Went directly to where the yellow/orange dose vacuum line connects to at the passenger fender and to my surprise no vacuum there either. No my question is. Am i suppose to have constant vacuum to the dpse or I'm I just being an idiot. And two if I am suppose to when the vacuum line runs into the passange fender where does it go from there and could I have a major issue in my hands?
Ford Excursion :: Vacuum Leak In The Lines Coming From Electric Pump
So, my original pump finally died and I replaced it....however upon doing so I realize there is a leak/crack in the lines as it never shuts off (explains why the factory one died).
After a bit of troubleshooting, I've discovered the leak HAS to be down in the passenger fender where the black and grey lines travel over the blower housing and go straight down up against the inner fender wall.
Where doe these come out or connect? I clearly cant get a hand down in there...does the inner fender well have to come out to access this? or is there a junction box/splitter somewhere accessible?
Ford Super Duty (1999-2016) :: Removing Hub Vacuum Lines
I have manual hubs on my truck. Can I pull those vacuum lines and plug the holes?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Vacuum Lines Sizes To 4WD?
Time to replace the aging vacuum lines to the 4wd and probably anywhere I can find the old rubber stuff.
What is the size of the lines and are they mostly the same?
I'd like to order a roll so I can make ones like the front hubs longer, stuff like that.
Ford F-150 - 1997-2003 :: Vacuum Reservoir Lines Under Passenger Fender Broke Off
I have a 1997 4.2 and when i got it the big vacuum reservoir under the passenger fender had the lines broke off. Where these lines go or have a diagram...
View 1 RepliesFord F-150 - 1997-2003 :: Check Engine Light On - Rubber Vacuum Lines
I got a question, what is after ac hose vacuum left side on a 10 th gen 4.2l engine bay by the firewall, to the right of the blue thing, right of that on that line their is a 2 end diameter rubber vacuum line? What is that called, I need a replacement.
View 7 RepliesFord Super Duty (1999-2016) :: Removal Of Vacuum Lines For ESOF?
Truck has been neglected for a while so this upgrade/repair I installed Powerstop brake rotor, caliper, bracket and pads. New Timkin wheel bearing, Moog U-Joints, and new inner/outer axle seals. Also replaced all the brake hoses and the remaining original rusty brake lines. About a month before I replaced the failed Auto/Manual vacuum operated locking hubs with Mile Marker units, which do not need the vacuum line, the drivers side was missing. and was letting water into the wheel bearing. So I decided to plug them and remove the vacuum lines from under the hood as well.
If there is interest I can get pictures of the vacuum lines, and what I changed under the hood. That was pretty self explanatory.
Could not find a google search for the thread size of the vacuum nipple in the knuckle. It is a 3/8"-24 fine thread.
[URL]
Ford Super Duty (1999-2016) :: 4x4 - Vacuum Lines Starting To Look Brittle
I don't have any leaks at the moment, but after inspecting my vacuum lines they're starting to look brittle and I want to replace them proactively. Is there a kit to do this or should I just cut a section off and take it in to an auto parts store to match the size, and buy it by the foot?
View 2 Replies