Ford Ranger / B-Series :: 1998 - 4r44e Transmission - Randomly Losing Power While Driving Like It Would Not Shift
Ok I've got this 98 Ranger with the 2.5L and the 4r44e automatic. The engine is used and has about 100,000 miles now and is it a good state of tune - so I think. The transmission was a remanufactured I bought a few years ago that was built with the shift improver kit, Kevlar bands, extra planetaries, 4wd pan, and external cooler. It's now got 92,000 miles on it and it's been serviced every 30,000 with a fresh 4wd filter and Mercon V fluid. It's outlasted the last 3 transmission I've had in my Ranger. I've got 315,000 miles on the body. For awhile it was randomly losing power while driving like it wouldn't shift, almost like it dropped a couple cylinders, then as you kept your foot on the gas it would recover and rev up and shift.
Then sometimes randomly at stoplights it would shake at a stop and have no power at take off until it hits 30-40 mph. Sounds like a converter, is what I thought. But now it's doing it more often but not the shaking at stoplights as much as randomly losing power while driving normal speeds. Last night I drove it about 50 miles after doing a fresh filter and fluid change and this time it did it so much it threw a code up P1131. Even though that's a O2 sensor code, could it be hidden by a transmission valve body problem? One transmission shop said it could be a valve hanging up just by me describing it to him. Could this be ignition or fuel related or is it all tied in with the transmission problem, if it is even a transmission problem?
Ford Ranger / B-Series :: Won't Shift Into 5th Gear?
ive been experiancing an issue with my trucks shifting. it shifts smoothly but doesnt like shift into 5th, as im driving it stays in 4th longer than necessary. my thought was that it was tied to a shift sensor, what do you think?
View 5 RepliesFord Ranger / B-Series :: 1997 Won't Shift Out Of Park
I have a '97 Ford Ranger with an automatic transmission that wouldn't shift out of park last night. A friend opened the hood and jiggled the steering column some, and finally it shifted. We checked the transmission fluid and it is full, a dark brown color. What the problem might be?
View 3 RepliesFord Ranger / B-Series :: 2000 - 4WD Hard To Shift
2000 ranger 3.0 auto 4wd hard to shift. Are the cables known to stretch?
View 6 RepliesFord Ranger / B-Series :: 1999 - CEL / OD And ABS Light On - Won't Shift Out Of Low?
Yesterday my 1999 Ranger 2.5L Automatic got really wierd! The check engine light came on, the overdrive light started flashing, the ABS light came on, and the transmission can't shift out of low, except manually...and to top it off the speedometer quit working! What the heck is going on???? This has got to be all connected somehow.
Up until now, I have had no problems. The truck has about 45K miles. I change the oil at 3-4,000 miles and try to take care of this as my teenage daughter drives this truck to school.
Ford Ranger / B-Series :: 1999 XLT V6 - No Clutch / Can't Shift
When I got home today I went to back into my parking spot and couldn't get my truck in reverse, or any other gear for that matter.
I've been suspecting something was going to go wrong because the last few weeks or so when I push the clutch in it sounded like bb's rolling around in a metal coffee can. Since I have owned it (2 yrs) the clutch has seemed funny anyhow, as in I really have to feather it so it doesn't grab and stall out.
So I've visually inspected what I can so far. Master cylinder fluid is at a proper level and I pulled the inspection cover on the transmission. I didn't see any fluid and reached inside and there wasn't residue in there either. I observed the throwout bearing pushing the clutch cover fingers in when the pedal is pressed and that is about it.
Just wondering about some additional checks I can perform to pinpoint the problem, as well as how to fix it and get rolling again.
1999 Ford Ranger 4x4 XLT
3.0 V6
134,xxx miles
No modifications
Ford Ranger / B-Series :: 1999 - Trans Won't Shift Into Any Gear
i have a 1999 mazda troy lee b3000. The truck has a 3.0 flex fuel and 4r44e and when you go to drive it. turn the key engine fires up but the trans won't shift into gear. Here is the back story.Bought the truck brand new in 99 I'm the original owner it was a daily driver up until 2 years ago. the truck has over 300k miles and still ran great but the camshaft was starting to go. I was gona replace the cam but came across a killer deal on a new engine. picked up another 3.0 flex fuel with 50k miles. drove the truck into my garage removed the old engine installed the new engine. got in the truck turned the key and the new engine roared to life.
I went to put the truck into gear so i could get it out of the garage and go for a test drive and nothing. went to put it in drive and again nothing. no matter what gear its put in it doesn't move at this point i was confused and decided to quit for the night. That was in 2011 its now 2013 the truck has just sat there sense then. I've tried anything and everything even went as far as swapping transmissions and computers with no luck. I took the trans apart I don't know how many times can't find anything wrong with it.
Ford Ranger / B-Series :: 2003 - Hard To Shift After It Warms Up
I bought a 2003 Ford Ranger, 2.3, 5 speed manual. It is hard to shift after it warms up. I test drove it when it was below freezing, so I didn't notice it at first. The warmer the day and quicker the truck warms up, the worse it is. It goes into gear with no problem when the engine is off or if I'm still moving, but if I'm stopped there are times it is hard to get into gear. This really sounded like a clutch that wasn't fully disengaging to me, so I decided to pull it apart. I didn't check the movement at the slave before I started, but I did find the master was a little wet at the rod in the cab.
So, I did the following:
- New clutch master cylinder (system bled out of truck to eliminate air)
- New slave cylinder and bearing
- New pilot bearing
- Changed transmission fluid - Mercon III ATF
I inspected the clutch/pressure plate and it was in good shape and looked like it might have had 10K - 20K miles on it. The last owner said it was recently replaced and it looked it. So, I put it back in. After I was done, I checked the movement at the slave/pressure plate and it is moving about 3/8" - 1/2" when the pedal is down. I was happy and thought this would solve the problem since the old pilot bearing seemed stiff and I saw the leak on the back of the master cylinder.
I drove it and all felt fine at first, but it was a cool day and I didn't drive it that long. When it was warmer over the next couple of days, it started getting hard to shift again. It's not been quite as bad as before, but still doesn't shift right.
Ford Ranger / B-Series :: 2004 - Hard To Shift Into Low Gear
It's a 4 cylinder 5 speed, and once or twice a day when the light turns green and I go to put it in low gear, it just doesn't want to go into gear easy. It's like the syncro isn't happy or something. The clutch is depressed all the way and not dragging.
View 14 RepliesFord Ranger / B-Series :: Change Shifting Points - Shift Into 5th At 45 - 50 Instead Of 55?
I have a 2002 3.0 with the 5R44E. I don't like how late it shifts into 5th gear. Is there a way to make it shift into 5th at 45-50 instead of 55? I feel like I have to let off the gas half of the time to make it shift and I don't have a heavy foot. If anything, driving with a light foot seems to make it shift into 5th later.
View 8 RepliesFord Ranger / B-Series :: 2003 - Sluggish To Shift Into 2nd Gear?
2003 3.0 FFV 5 speed automatic...... Just noticed recently that it seems slow to go into 2nd gear.....the rest of the shifts seem fine, firm and unchanged.....
View 4 RepliesFord Ranger / B-Series :: 2002 - Hard To Shift Gears
I have a 2002 ford ranger edge. swb, 3.0L, 5spd. I have been noticing it is getting harder to shift gears, put in 1st at a stop light lately. There is no grinding just seems harder to engage. Checked fluid level and it is clean and full. Recently i have developed a vibration under power. Let off the gas and smooth as can be, apply throttle and starts vibrating. Not sure if flywheel is "hot spotted" or perhaps broke a spring on pressure disk. Just seems odd it's only under throttle. Yes already checked rear end and U-joints.
View 2 RepliesFord Ranger / B-Series :: 1989 - Disengage Electronic Shift?
I recently acquired a 1989 Ford Ranger midsize pickup with an electronic shift button/console between the visors. I put it in 4WD and the manual does not indicate the procedure to take it out of 4WD. What is the procedure?
View 3 RepliesFord Ranger / B-Series :: New Clutch - Hard To Shift Going Into 1st / 2nd And Reverse Intermittently
1997 Ranger extended cab, 222k mi., 4 cyl, standard transmission. Shifting got worse until it finally died and the mechanic replaced the clutch "kit" and slave cylinder.
It still fights back going into 1st, 2nd, and reverse. But it is intermittent. If I put it in neutral, depress the clutch, and start the vehicle, then, after a few seconds wait, when I try to go into 1st (or reverse), it fights me back, forcing me to pause and apply about twice the pressure I should need to go into gear. When I go forward in 1st, and am ready to shift to 2nd, it fights back so that I have to pause just a bit and apply more pressure than I should for it to go into 2nd gear. 3rd, 4th, and overdrive are FINE. Also, the clutch seems to disengage about halfway down, where I was expecting it to disengage after only 10 -20% depression.
The mechanic doesn't see the problem (or won't admit it). Is there an adjustment to make the clutch disengage with only 10-20% depression instead of the 50%? Is that something I should be worrying about?
Is there some other problem? Like maybe the synchromesh mechanism in the transmission itself not bringing the transmission rotor to engine speed soon enough (wear on the synchromesh)?
When it was new, it went into ALL gears with ease, no fighting back, and it starrted doing this after about 150k miles. Now, at 222k mi., even with a new clutch, plate, throughout bearing, and slave cylinder, it still seems partially stuck going into 1st, 2nd, and reverse.
I just don't want to start replacing things until I can get a correct diagnosis as to what is causing the problem.
Ford Ranger / B-Series :: 1993 Manual Trans / Hard To Shift Into First
I'm having a little issue with shifting into first. Once in a while it simply will not go in, like you're pushing the shifter against a brick wall. If I turn off the truck and turn it back on, it works absolutely fine. I can shift into 2nd-5th no problem at all times. Is it just the shift linkage, or...? I'm not really sure where to start.
View 7 RepliesFord Ranger / B-Series :: 1998 4.0L Manual Won't Shift As Soon As Start The Engine
I'm 1200 miles from home living in a hotel right now. Was on my way to the store this morning and I took it out of gear. When to put it back in, and it wouldn't go in. Fortunately, I was still moving, so I coasted off into a parking lot. Once I shut the engine off, it went right into gear. It moves freely through them all. As soon as I start the engine, it won't shift. It is not my clutch. I can start the engine with it in gear and the clutch in, and it won't creep at all (was sitting on level ground when I tried). At least this means I can get it places if I slip the clutch a lot. Took the inspection cover off, and all looks well in there. It hasn't been acting strange. It shifted just fine right up until this. No strange noises either until now.
Now there is a slight squeaking sound if I try to force it into gear with our without the clutch pushed in. Since I've never let a mechanic touch my baby before, and I have to now, what possible things should I be looking for to make sure they are honest? I'm thinking maybe I killed my pilot bearing? Second, while its apart, I'm going to have them replace the clutch and slave cylinder since its got 160K on it and as far as I know, the previous owners never did that. Recommendations on what clutch to get? Its been towing some lately. I don't know if that makes a difference.
Ford Ranger / B-Series :: 1999 - Hard To Shift Smoothly Into Third Gear
I have a 1999 ford ranger 4x4 with automatic 5r55e and it had problems shifting smoothly into third gear. I changes the valve body gaskets and the (rooster comb) detent lever. Now it shifts very hard and has on first second and passing gear.
View 6 RepliesFord Ranger / B-Series :: Shift Lever Sloppy / Truck Won't Start
I have a 96 ranger 4.0L shift lever was very sloppy and one of the torq bolt fell on the floor I used loc tite and tightened them up with no problem put everything back together and now it wont start. I think I checked everything even replaced the neutral safety switch, adjusted the tranny cable, checked fuses and switched around the relays maybe an ignition switch? I am running out of stuff to troubleshoot.
View 13 RepliesFord Ranger / B-Series :: 2003 - Hard Shift - Transmission Or Clutch?
The truck: 03 Ranger, 2wd, 2.3L, 5spd, 160k mi
I bought the truck two years ago and it's always been difficult to shift (especially into 1st, 2nd, 3rd). I don't drive it often and only put 5k mi on it since I bought it.
The problem: Someone more mechanically inclined than I once told me that the hard shifting is probably due to the clutch not fully releasing due to low hydraulic pressure brought about by a failing slave cylinder.
I just noticed today that there is a high-pitched squeaking coming from somewhere on the truck. At first, I thought it was the rear end, but now, after pulling it into the driveway, I noticed that the squeaking noise vanishes when I push in the clutch pedal and returns after I release the clutch pedal and drive in 1st gear.
The transmission oil level is good, but I've never changed it and I'm not sure if the previous owner ever did either. I'm hoping I haven't damaged the transmission.
After reading a few threads, it seems the problem might be the input shaft bearing. To replace it, I'd need to drop the transmission and borrow a couple of tools I don't have (feeler gauge and bearing puller). If the ISB is the problem, it seems like it would be a good idea to change it now before it seizes and leaves me stranded somewhere.