Ford Ranger / B-Series :: 1994 4.0L - Starts / Stumbles And Dies Soon After
Ole girl finally let me down, or I let it down at 224,000mi. Started just fine one early cold morning and in about 30 seconds started stumbling and down for the count she went. Acts like it wants to run but will only stumble.
Checked inertia switch (ok) and all vacuum lines/caps appear to be fine. I was kind of due for new set of plugs/wires and a fuel filter. Replaced all didn't see any problems with the old when pulling. She will run for a few seconds, but stumbles and not smooth while running. Checked fuel pressure KOEO 40psi steady. I can hear fuel pump charge system per as usual.
Seeing as it is super cab checked for chafing on wiring to fuel pump under cab. Looks fine. I've heard tell could be alternator, which seems odd to me. Wondering if it would be worth pulling it off and taking it in for a bench test? Maybe I missed something. I know the intake gasket is suspect.
Ford Ranger / B-Series :: 1984 - Dies While Turning Right?
I didn't really know where else to turn (no pun intended) every time I turn my wheel to the right the truck sputters out and dies, i checked the ignition switch, tightened her up and shes still killing the engine when i turn right. All other power remains on stereo, car charger etc. its not so bad on continuous turns i can just pop the clutch but for stopping and turning its a huge issue. Why turning left is fine but right kills the engine..wondering if maybe the prongs on the ignition switch may be bad?
View 7 RepliesFord Ranger / B-Series :: 1995 - Top End Knocking Noise
Had the top half of the intake off (2.3L) and fixed some vacuum leaks and replaced a power steering pump. Started truck and it ran funny like missing on one cylinder then cleared up then started making a loud knocking noise and running rough. Assumed that it swallowed something when I had the intake off and it got into a valve or into the cylinder. I pulled the plugs and there are no obvious signs of a problem. I also did a compression test and all 4 were around 150psi.
Put the plugs back in and started it and the same noise was there. Removed the serpent belt just in case it was power steering pump related and the noise was still there when I started the truck. Sounds like something is inside the engine still. Going to get a friends bore scope to check further. I guess I will split the manifold again and run the scope in there. Pending that I may also look down the plug holes with the scope. This is a major bummer. Not what I needed.
Ford Ranger / B-Series :: Starts Then Dies After Few Seconds
I have a 2005 ranger SOHC 4.0 new rebuilt engine It starts then dies after a few seconds then doesn't start at all unless it sets for a few hours or over night and will do same thing. It has 60 psi on fuel rail, good spark I'm starting to think my PCM is causing all this?
View 14 RepliesFord Ranger / B-Series :: 1985 - Bogs And Dies While Driving
I have a 1985 ranger 2.3l efi and it bogs and dies while while driving, it can sit and idle all day long but when you go to drive it, it works great for 3-4 minutes then out of nowhere starts bogging sometimes I can keep it going a little longer but in the end the truck always dies . I know I'm loosing fuel pressure , I hooked a gauge up to it and drive it down the road when the truck died it showed 10 psi , from here I'm lost . It has a new fuel pump in the tank and I can hear the other one running when I click the key on , Also two new fuel filters .
View 3 RepliesFord Ranger / B-Series :: 1987 - Engine Dies While Driving
Recently, today in my 87 Ranger suddenly the engine dies and all electronics in the cab fail.
I noticed under the hood that the fusible link connected to the battery and an orange and black wire was smoking. Tracing this line i found that it leads to the ignition switch, as well as some other places.
There is another fusible link and the junction between the yellow ignition wire and the orange and black wire from the battery. This fusible link also was failed.
I'm planning on replacing the fusible links tomorrow but in case that does not fix it, where to look next.
The problem only occurs when the key is in the ON position. I'm thinking maybe I could do some tests with a multimeter on the ignition switch but am not sure of the details of what I should test for.
Summary: Fusible Links C, and E burn out when the ignition is in the ON position.
Ford Ranger / B-Series :: 1987 - Knocking Sound In Engine
I just bought a 87 Ford Ranger 2.9L v6 4x4. It has a tick to it. It doesn't stop, it doesn't increase with acceleration it stays the same. I sprayed some SeaFoam in it and It improved the performance a lot (More horsepower, better reaction to the pedal.) But it is still knocking. I have never tore apart an engine before or messed with lifters or anything. I'm not completely sure how to fix it. I know knocking is not a good thing either.
View 6 RepliesFord Ranger / B-Series :: Dies / Won't Restart - Motor Stumble Every So Often
My MILaw Truck 1992 ranger isnt running good and I need to get it going
Only a P0111 at this time IIRC
We started the truck tonight and idel ok Could see the motor Stumble every so often. She went to drive it and it Cuts out under Load Or you must rev it up to keep it from Stalling.
And if it does Cut out you have to let it sit for 5 minutes to restart what is Weird is it dont Smell Flooded either I smelled the VAC Line to the FPR and it was DRY and Did NOT Smell like Fuel.
It was dark didnt do much trouble shoot as the Flashlight died. I wonder about Fuel Filters. And Also about the Idel Control. The Mis or Stumble seams Random
Any testing I can do I have a DVM and that Code Reader. Might have to find something to check fuel press with where would I check it at the fuel rail I assume. Going to try and go over the Basics tomorrow If there is Anything Specific I should check?
Ford Ranger / B-Series :: 1988 2WD Dies When Clutch Is Released
My Grandpa has an 88 Ranger 2wd with the 2.9l V6 and a 5 speed, I believe, M5od. I was driving down the highway when I heard a noise. I tried throwing the tranny in neutral but when I pressed the clutch pedal in, I had no pedal whatsoever. Engine took awhile to restart. It'd turn over a little almost as if a rod was bent or something of the sorts. Eventually the engine started and would stay running as long as the clutch was pressed in (disengaged).
The engine dies no matter what range the transmission is in,neutral included unless the clutch pedal is depressed. It Will die when the clutch is released in any gear with no forward movement that is noticeable. I can spin the tail shaft with the driveshaft installed and all gears in neutral but the input does not spin at all. Input shaft wont spin at all, period. I originally thought the slave cylinder was KIA but now I am very confused on what the problem could be? Is there a bearing the input shaft rides on that may of seized?
I pulled the tranny last night and took the top cover off. Yes, I made sure it was in neutral when I removed the cover. I can manually shift the collar to all gears by hand, 5th and reverse included. I'm stuck between a rock and a hard place here and where to go from here. I have bought a new clutch assembly and slave cylinder. This truck was bought by my Grandpa brand new in 1988. It has 98,000 miles and everything is original. I did forget to mention that there was very little oil in the trans when I drained it and it appeared to be gear oil vs ATF.
Ford Ranger / B-Series :: 1994 V6 - When Hot Start Will Not Idle / Dies Out
94 Mazda B4000. V6 4x4 manual
After engine has ran about an hour, I make a stop at location, then on startup engine has a hard time staying idle after engine it's warm. Cold start idles fine, hot start it dies out. I must rev gas for truck to stay on. What could this be?
Ford Ranger / B-Series :: 2002 - Knocking Felt In Steering Wheel
I have a 2002 Ranger 2.3L 5spd w/ 16,000 miles. Have noticed this problem for 6 months, been to dealer 3 times now. They say nothing is wrong. What I am "feeling" more than hearing, is a slight knock in the steering wheel, particularly when driving over dips and mild to moderate bumps. This is usually when moving in a fairly straight line, not much tension on the wheel.
It reminds me of problems I had on much older cars/trucks when there was a loose shock/strut or play in a ball joint or tie rod. It is annoying because it feels like something is wrong. Dealer can't find anything. Perhaps something not installed properly that loosens and bumps/knocks into other components thereby transferring vibrations through the steering column?
Ford Ranger / B-Series :: 2003 2.3L - Pinging / Tapping Or Knocking Noise
My 2003 Ranger 2.3L When I purchased it in 2005 I never noticed this tapping noise until in 2007 when Tennessee forced 10% Ethanol added to fuel. That is when the noise started.
What this could be. I have since moved to Texas and found a station that sells Ethanol Free gas, but that does not remove the noise.
Ford Ranger / B-Series :: 1992 - Engine Dies Randomly While Driving
I have just inherited my recently deceased father's 1992 Ranger with the 2.3 liter engine. He was a Ford Mechanic but got to ill to worry about fixing the Ranger. So, let me begin, the engine dies randomly, (at idle or in gear driving doesn't matter what gear or speed), turning key to off and then to on will allow vehicle to restart every time. No "Check Engine" light has ever lit, I do have an "Antilock" light that comes and goes. The engine codes I keep getting are: 10, 218 and 222.
Code 10 is a computer check code,
Code 218 is "Loss of Ignition Diagnostic Monitor (IDM) signal/left side, and
Code 222 is "Distributorless Ignition System - Loss of right side ignition diagnostic monitor (IDM) signal.
These codes were from my Innova reader. I have read where other similar problems were fixed with a new Crankshaft Position Sensor, replaced mine, no change. Another symptom I just noticed is my temp gauge stays near the cool end when it should be higher.
Ford Ranger / B-Series :: 1989 V6 Stalls / Dies / Powerless After Warm Up
I've recently acquired a 1989 ford ranger xlt 2.9L V6 and iv got my elbows deep already..... starts right up and scene its an older truck i let it warm up for a few minutes seems to sound alright so i jump in and take off... well i make it about two blocks and as soon as the truck seems to warm up it starts to sputter and die out... starts back up and idles for a min and i try to take off, but it seems to have NO power and jerks and dies.... so i push to a street parking spot and get situalated start the truck up again and take off only to make it about half a block tell it does the same....
First i think iv run outta gas witch i might of not sure so I walk to station and get three gallons. put in truck and same is happening. so i start kicking myself for not haven any tools with me and i leave tell next day... that night do a little research and get some idea's of what could be the problem'(s) so i start out with things that look like they need tending Badly WIRES, PLUGS, ROTOR, CAP, MAP SENSOR, and now after a whole day in the rain (Northwest BTW) and grease to elbows? 2.9 V6? What step's should i take next?
Ford Ranger / B-Series :: 2004 Truck Dies / Stalls While Driving
The problem : I bought a 2004 Ranger truck and after two days it started to hiccup, or stall or die while driving, then because the truck is manual, just start up and keep running. It was the strangest thing.
I gave it to a shop, and after checking the electrical, the ignition, the fuel system, the drive train, and ten hours of troubleshooting, they came up without an answer. So they gave me the truck back.
Answer, a few days after taking it back:
I had told the shop that it had been sitting for 6 months, May till January, but when I told a mechanic friend a bit later, he still suggested 2 bottles of gas line antifreeze in the tank, before the next tank fill. I did that, and there was some improvement.
Next, When I replaced the balding tires with new Nokian Winter tires, the tire shop, (Kal Tire), told me that the air cleaner was incredibly dirty, and asked me if I would like them to replace it. I said yes, thinking that it might just do the trick, as no one in the forums I read, had mentioned it.
Success! No hiccup or stalling and it has not died since.
Ford Ranger / B-Series :: 1990 - Rough Idling / Truck Dies
1990 Ranger 2.3L 4 cylinder. The truck idles so rough it dies. It runs fine going down the road it just seems to "load up" at idle. I know there are hundreds of things that it could be, I just hate to start throwing parts at it. It is definitely running rich at idle.
It is one of those trucks that we have replaced a lot of parts. The scan tool said something about setting the timing??? Is there a way to set the timing? There is no distributor, and it is the one with 2 coils and 8 plugs.
Ford Ranger / B-Series :: 2001 - Engine Swap / Knocking Noise For A While
I have a 2001 ford ranger 2.5 and a standard 5 speed. Its been knocking for a while now and recently its made a much lower tone knock, I am thinking I may have thrown a bearing. Also I am wondering what other engines I can use, besides the 2.5.....
View 3 RepliesFord Ranger / B-Series :: 1999 - Stalls / Rough Idle And Engine Dies
I have a 1999 B4000 4.0L with 160K miles on it. Bought the truck new. Up until about a year ago it ran perfect but has developed an idle, stalling and occassional jerky ride problem. It occurs at any temperature, engine hot or cold, A/C clutch on or off and in Park, Drive or Neutral. When you start the engine it will not idle unless you keep your foot on the gas. The idle speed will drop to 200-300 rpm and the engine dies. Sometimes you can barely tap the gas pedal and the rpm will shoot up to normal idle speed (about 900 rpm) and stay there a few seconds then begin to drop again. If the engine is cold it will often die a couple times after starting even with the foot on the gas and then about the 2nd or 3rd time run with your foot on the gas.
At stop signs and red lights you have to keep your foot on the gas to keep it running. If you are approaching a stop sign and take your foot off the gas to coast to a stop and brake, the engine rpm will drop and the engine will die. It always starts fine though. Once you are driving it generally runs just fine at low or high speed. You can generally set the cruise control on the expressway and cruise right on. However, sometimes all of a sudden the truck will start bucking and jumping as if it has a terrible misfire. It usually lasts a few seconds and quits. Often if you step on the gas it quits. Even less occasionally the engine will begin to slow as if it is starved for fuel and slow down. You can press the pedal to the floor and it sputters a bit then picks up and runs fine.
I have read about all the threads in this forum and others and tried some of the suggested fixes but it still has the problem. I have tuned it up with new plugs, wires, fuel filter, air filter and PCV valve. Based on some of the forums advice I have replaced the IAC valve, the EGR valve and EGR Pressure Feedback Sensor, and cleaned and inspected the MAF sensor with MAF cleaner. I have checked all my vacuum lines and no leaks there and checked the engine timing which is fine. Fuel rail pressure and engine compression are also fine. Spark plugs show no clues, exhaust is clean and the engine uses virtually no oil. There has been no tear down on the engine like removing the heads, cam, timing gears or any of that and the engine is completely stock.
It shows no codes related to the problem. Two or three months after the problem started I showed a code that indicated an injector problem, traced the problem to a bad injector, replaced the faulty injector and it was fine. That took care of that code but didn't solve the idle problem. In my younger days I was into drag racing and I rebuilt engines, swapped transmissions, etc. and still do my own tune-ups today so I am fairly familiar with auto repair and have most of the tools for testing newer cars but this one stumps me. As a last resort I'm about to take it to the dealer.
Ford Ranger / B-Series :: Truck Almost Dies And Starts Sputtering - Spark Plug Caps Pop Off
My 2003 2.3L used to run bad... it had a lot of lag to it when i would try to accelerate. The check engine light was on so i got it checked, and the reading said o2 sensor high voltage or something like that... anyways, i purchased a new sensor (i researched, and found there is only an upstream o2 sensor), replaced it, and the truck ran WAY better, no more lag during acceleration, it was crisp. As i was driving home one day, i was accelerating up a hill, and at about 4000 RPM, the truck almost dies and starts sputtering.
The check engine light started flashing, so i new it was serious, but luckily i was able to make it back to my house. When i got home, i looked under the hood and noticed that #2 & #3 spark plug caps had popped off the spark plugs. What I don't understand is what would have caused that to happen in the first place.... Is it a clogged Catalytic convertor, or is the o2 sensor bad.... Ive read different opinions and technical diagnostic possibilities, but man, i don't want to throw a bunch of money at a truck that I'm really going to have for a few more months. but I need to get it fixed in the mean time.