Ford Ranger / B-Series :: 1994 - Lifter Knock At Start Up / Throttle Hold Over 3k?
I've got a '94 Ranger with the 4.0L OHV and an Automatic trans. When I start, hot or cold, it has quick lifter knock for only a fraction of a second. This same knock comes back if I hold the throttle over 3K with NO LOAD on the engine. With any load, I cannot make it knock. With no load, though, it becomes very loud, especially with more RPMs. at idle and slightly above, there is a slight tick that can only be heard with the bonnet up, and then it is only slightly noticeable. I think that this tick is unrelated, but I figured I should share that information. For oil, I run Pennzoil high mileage 10W-30, changed 3000 miles religiously. Purolator filter, PL30001. I can understand the startup knock, but I can't see why it seems to produce the same knock at high RPMs under NO load.
View 4 RepliesVolvo :: Accelerator Has To Be Hold To Start
Sometimes I have to hold the accelerator the floor and it starts. Sometimes I get a faster than normal cranking speed and no start. When this occurs I can hold my foot to the floor and it will backfire through the intake. After some time of this the car will start.
Here's what I've done so far.
1. Checked timing and timing belt - OK
2. Ignition system check coil, wires, plugs - OK
3. Fuel system pump, injectors, and regulator - OK (Regina fuel system)
4. Checked and changed the relay and the cam sensor - OK
Ford Ranger / B-Series :: 1994 XLT 2.3L - EVAP System Would Not Hold Pressure - Diagram?
I have a '94 Ranger XLT with the 4 cylinder 2.3L motor. I recently failed my smog test here in CA because the evap system would not hold pressure. All the emissions were perfect, but it wouldn't hold pressure. I changed the fuel filler neck -- it was cracked -- but there is still a problem somewhere. Is there a diagram that shows where all the hoses are for the evap system? I'm thinking that some other hoses might be cracked since they have been there over 20 years. Is this a good place to start looking or should I be checking something else?
View 4 RepliesFord Ranger / B-Series :: 1999 - Rough Idles When Started / Have To Hold The Gas Till It Warms Up
Quick back story I bought a 1999 Ford Ranger It is a 4 cyl with an auto trans the guy said it had some trouble with the tranny (major understatement) he also forgot to mention he cut out the CAT. so running a 4 banger off the header.
When you start the truck it rough idles but you have to hold the gas down til it warms up. You can shift into reverse but it labors the motor and the motor will not up the rpms kinda stays at idle and wants to die no matter how hard you accelerate and you can't move up a slight incline.
When you shift into drive you have to rev the motor to 3 grand an it will catch then move slowly forward. no matter how high the revs go. The fluid levels are a tad above the full level and a bit dark for my liking.
Ok, I used an OBDII scan tool from the parts store and it came up with 3 codes P0351, P0352, P0500. From my internet search the first two seem to be coil related which explains why the motor is running like garbage. The last may or may not have to do with what the tranny is doing.
Ford Ranger / B-Series :: 1984 2.8L V6 - Accelerator Pump Leaks?
I have a 1984 Ford Ranger 4x4 with 2.8L V6, carburetor number E37E-AEA. The accelerator pump diaphragm is perforated.
Small holes are visible when I hold it up to a light. Is this part available anywhere? Is it included in these carb repair kits that I see on a lot of auto parts sites? The sites don't list the contents of their "kits."
Ford Ranger / B-Series :: 2003 - Cruise Control Set Button Broken / Accelerator Stuck
2003 ford edge 3.0 V6 ... I was driving down interstate today going 70, set my cruise control & the button broke. My accelerator was stuck, when I would hit the brakes it would literally shake the whole truck. What happened & why?
View 3 RepliesFord Ranger / B-Series :: 1994 - Downshifts If Step Harder On Accelerator At Cruising Speed
I have a 1994 4x2 shortbed standard cab Ranger XLT. It has the 4.0 OHV engine, A4LD Automatic transmission, and 195,000 miles. Under average driving conditions, it operates fine. It shifts up through the gears much like it always has, although the shifts may not be quite as firm as they used to be.
If I'm at cruising speed and step harder on the accelerator, it downshifts, RPMs increase, and it upshifts rather poorly, & then I feel a thump, (maybe the torque converter locking up when it shouldn't be?), and I'm in the higher gear. This seems to happen when it upshifts from 3rd to 4th gears for sure, maybe from 2nd to 3rd, but I'm not sure.
Again, it only seems to happen when I attempt to speed up from cruising speed, not from a stand-still. The transmission fluid and filter have been changed at regular intervals, and the truck has never been abused. The fluid is red in color, doesn't smell burnt, and the level is correct. I don't want to get rid of this truck if I can avoid it. It has been super-reliable and mostly trouble-free for the 16 years I've owned it. What might be wrong with it?
Ford Ranger / B-Series :: 2000 - No Start - Wiggle The Shifter To Start?
2000 ranger auto 3.0 wife said that she had problems starting the truck
She had wiggle the shifter to get it to start. Have not looked at it yet but i am think the newtrl safety Switch.
Ford Ranger / B-Series :: 1994 2wd Will Not Start When Key Is Turned To Start Position
I have 1994 ranger 2.3 2wd will not start when key is turned to start position - when clutch is depressed there is a click from fender mounted solenoid but it never cranks motor or starter--I need wiring diagram to trace origin of wire on starter solenoid because it does not have 12volts on it--when I jumper 12v on it and have it in neutral it starts up and runs but no voltage and no start with key....
View 2 RepliesFord Ranger / B-Series :: 2000 - Won't Start?
I have a 2000 Ranger 4.0L manual transmission. I just replaced the starter/solenoid on it a few days ago. I went to start it, and I got 1 click and the whole system goes dead (ie: lights, instrument panel, everything!) I checked all the fuses and the starter relay in the fuse box. All good. I tested the battery, it's charged and good. I even tried jumping it. Same problem.
I can remove power from the system, re-apply power and same issue. I'm not even sure where to start here. I checked the ground terminal on the battery. It's connected to the frame and clean. Cables are tight to the battery and clean.
What am I missing?
Ford Ranger / B-Series :: 1986 Just Cranks But Won't Start
I have heard from a few people that it might be the computer that is messed up. Just replaced cap and rotor, spark plugs, wires, fuel filters. Pump turns on. Cranks and cranks but won't start. Took the intake cover off and tried starting it, all it did was back fire. Checked the firing order and everything is right. So im left with guessing at the computer and ignition??
View 5 RepliesFord Ranger / B-Series :: 2002 - No Start When Shut Off
I have a 02 ranger..3.0 standard trans 4x4.... Started running crappy, cleared up and when shut off, now wont start... Good spark and good gas pressure... Seems to want to try, but just doesn't go. No codes or pending codes.
View 8 RepliesFord Ranger / B-Series :: 1991 - Turns Over But Will Not Start
My 1991 ranger with a 4.0 turns over but will not start. It acted like it ran out of gas put again seems to do ok then it did same thing it sat over night then would not start so I thought I would put some gas in the intake so it starts ran real rough but smoothed after a few minutes ran fine after that next morning same thing no start did same put gas in intake at first no start just turned over didn't even try let it sit for awhile then tried again it fires up ran rough but ran now I get nothing just turns over pulled codes 22and 122 replaced both had ignition mod checked its good new coil pack no change so at this point i hear fuel pump kick on fuel getting to fuel bar but seems a bit week on pressure going to get pressure gauge and see what it says but in the meantime I am loosing my mind...
View 9 RepliesFord Ranger / B-Series :: 2003 - Won't Start When Warm
My 03 ranger with a 2.3 I4 does not want to restart when it is above about 80 deg outside and engine is warm. Will crank, but as soon as fuel in line runs out it stalls, like a vapor lock. After about 45 mins can push start normally( has manual trans) but have to wait about 2 hours to use starter to start.
View 11 RepliesFord Ranger / B-Series :: No Start When Warm Becoming More Frequent
2002 Ranger XLT auto 3.0 will not start after it has run awhile, Was very intermittent at first sometimes six months would pass, sits for and hour or so and would start right up and run great. Lately it is becoming more frequent. Good fuel press, good spark, I have changed the coil pack, fuel relay, filter , am at a loss.
View 6 RepliesFord Ranger / B-Series :: 1988 - Won't Start - No Spark
Any way to tell if the ECU is faulty? I hooked my analyzer up to my friends 1988 Ford ranger 2.3L and it wouldn't even detect that the ignition switch was on. He was driving it the other day and is shut off on him while he was making a turn and it wouldn't start back up. We have rebuilt the distributor by replacing the pick-up, rotor button and cap, and we had the ignition module tested and found it was good. We have also replaced the coil. When the ignition is turned to the on position, the fuel pump comes on and never cycles off.
View 8 RepliesFord Ranger / B-Series :: 1994 - Won't Start After Warm Up?
I have a 1994 Ford Ranger 4.0L 4x4, 130,000. I love this truck but about a year ago it started not starting after it warmed up short distances in the summertime? It start right up on cold crank...Runs smooth idles like a champ...but if i shut it off..wont start for 20 to 40 min??? It doesn't happen in the winter months??? So I changed the fuel pump, filter, relays. I feel like it has something to do with the Ignition Control Module. Would that come up in a code?
View 13 RepliesFord Ranger / B-Series :: 1997 2WD Went From Fine To No Start
My son's 97 2WD Ranger with 2.3L, 5 speed, no a/c, basic XLT standard cab.
I was using his truck because my 93 Ranger was getting a new starter on it. I drove to work with no problems, then after work, it started just fine and drove a few hundred feet to a stop sign where it promptly died. I was able to start it again with some effort and drove to the next stop sign maybe a quarter mile away. Truck died again, but this time it would not start. Towed it home about seven miles and its in the driveway now. The previous owner had new Motorcraft platinum plugs and wires installed, new fuel filter, fuel injectors cleaned, all about 11,000 miles ago. My son has had it for about 6,000 of those miles.
It felt like it ran out of gas, but the gauge showed about 1/4 tank, and I put about 3 gallons more from a gas can into the tank with no change in being able to start it.
Here's what I've checked so far according to my Haynes manual:
Turned key and listened for fuel pump and it seems to go on just fine.
Checked fuses and they are fine.
Swapped around relays in distribution box with no change
Checked resistance at coil pack and it was about 1.7.
Checked resistance at one injector and it was about 1.7.
Checked inertia switch and it did not need a re-set.
I don't have the ability to check fuel pressure.
Ford Ranger / B-Series :: 1997 - Turn Over But Won't Start After Hot Sometimes
I have a 97 ranger with 3.0 it runs great but once you drive it and shut it off and go to restart it it will turn over but not start it used to start once I let pressure off the fuel rail, but now is a little harder to start when it does this but it looks as thou coolant comes out of the reservoir when this happens I think it might be coolant sensor or thermostat problem causing the timing to advance until it cools but then again why was it starting when I released pressure from the fuel rail and also I don't believe my check engine light works...
View 8 Replies