Ford Ranger / B-Series :: 1999 - Grinding Noise When Let The Clutch Up Off Floor
1999 ranger 3.0, 5 speed stick. I was backing out of my driveway but there was a car coming so i pushed in the clutch and waited for the car to pass, when I let clutch pedal up off floor i heard a grinding noise, a little while latter did the same thing in first. Is this a first and reverse gear scyronizer or something else. What causes this and how to fix it ?
View 10 RepliesFord Ranger / B-Series :: 2002 - Vibration And Grinding Noise?
Bought a 02 Ranger, 4.0 4x4 super cab 122,000 miles. etc Picked it up for 500 bucks because someone scrapped it along the side of a guardrail this last winter. Replaced rack and Pinion (cracked), Tie rods, Shocks, driver side knuckle and wheel bearing, and some body issues (bed is still shot so if any black short bed sitting around let me know). I've been kind of putting around all day in it, letting it used to working again. Starts right up, turns easily, I string aligned it so it goes where I want.
But as I get up to speed start at about 10MPG there is a vibration based noise coming from the front, can't pin down if its left or right. If Im going straight then turn it gets slightly more intense as I even start turning the steering wheel. The noise increases with vehicle speed. And I don't know if its separate or related, but any turn over 5-10* to the left results in a grinding sound but then I turn to about 10-15 and it gets less intense. No noise turning right.
I'm thinking a bad CV, TWO bad CVs, or a bad differential. Before I start ripping into those things, thought I'd get opinions, or hopefully experience in this area. I'm really hoping its something small and stupid. (like not getting a professional alignment)
Ford Ranger / B-Series :: 1999 - Slight Vibration Or Buzz When Upshift
Have a 99, ext cab, 3.0 , 5 spd man. 125,000 on it. I know the clutch will need replaced shortly but so far it is still functioning with out the slipping. Although I can feel a slight vibration, or buzz when I up shift. My immediate concern is the clattering/rattling. say at idle, not moving with the clutch pushed in when I shift into 2nd and 4th gear it really rattles loud. I can only assume it is some bearing inside the transmission, but need to have a bit more surety as to the problem. I know, I need to do the clutch however i don't know if the transmission is going bad or is that noise in the clutch area.
View 2 RepliesFord Super Duty (1999-2016) :: Rumbling And Vibration At About 40 - 55 MPH
Tires just balanced and rotated yesterday (second time just in case done wrong before). New ball joints and bars installed about 50k ago. Left front shock may be bad, but only slightly.
The issue: At about 40-55 mph, there is a rumble in the cab, unknown origination. Everything vibrates, although it "seems" like the left mirror is shaking more. The seat, floor, steering wheel, everything vibrates.
When I let off the pedal, vibration and noise go away, even within the "vibe zone". It only vibes when any throttle is applied, even just a tickle. I brought the engine up to the vibe zone RPM (1500-1800'ish) while in park and neutral, all seems fine.
I checked the U-Joints, they seem tight. I don't have access to a scanner, unless I want to pay the dealer.
Ford Excursion :: Rumbling Vibration And Noise While Climbing A Steep Paved Hill At 5 - 10 MPH
Ok...not sure were to go with this or how to explain it, while climbing a steep paved hill at 5-10 mph I get a rumbling vibration and noise. If I were to guess almost like axle wrap is causing the U Joints to bind or something. Runs and drives fine other then that. If I put it in 4x4 it does not happen, only seems to happen when wheels cant slip while climbing hills at LOW speed.
Don't notice it if climbing a dirt hill. There is a hill at the kids baseball fields that is steep and paved that its really bad on, way to busy right now to play on it to see what's happening. Tranny was looked at and oil changed.
New BDS 4" lift - had same issue prior to lift, though stock springs were worn.
Searched the form but really didn't come up with anything at this low of speed. While in Wisconsin the resort we were at the paved hills were so steep it felt like something was going to break. Put it in 4x4 and it was fine. This was with stock leafs.
Ford Super Duty (1999-2016) :: 2002 F250 - Front End Noise / Slight Vibration In The Floor
2002 Ford F250 4x4 Superduty Lariat (4 door). Just changed the locking hubs to a new set of Warn manuals. I began to periodically hear what sounds like a rumbling/bearingish/howling kinda sound. Happens when you hit a bump at any speed...then howls till you hit another bump..goes away..then process repeats. Come to a complete stop, and the sound usually goes away till you hit another bump. The hubs are "free" at this time.
Heres the weird thing...when the noise starts...I switch it into 4 wheel drive on the dash...the sound instantly goes away. Click it back outta 4 wheel drive (hubs are still unlocked this whole time) and the sound is gone. drive some more down the road, maybe hit a slight bump, and the sound returns. Switch it back into 4x4...sound instantly goes away. Its not really in 4 wheel drive, cause the hubs aren't locked in...but that cures it till I take it back out. What could be causing this howling ? Its getting worse, and you can feel a slight vibration in the floor now when its doing it.
Ford Super Duty (1999-2016) :: Vibration At 70 MPH / Heavy Rumbling
I have an issue with a truck I recently purchased. I have a vibration that starts around 50, feels like a wobbling vibration. Than once I hit 75 it feels like the truck is going to fall apart. Heavy rumbling.
It's a Ford F-350 dually extended cab. With 115,000 miles on it.
I took it to the shop to balance out the wheels and all the wheels needed atleast 2 oz of weighs on each side. Some have as much as 4.75 oz on one side. Is it possible that I need 6 brand new rims?
Ford Ranger / B-Series :: 1992 - Passenger Side Floor Getting Wet
Ok I got the brake pull fixed (I think) on my 92 Ranger 4x2 4.0 extended cab. I still will have to change the driver's side brake hose for prevention and the driver's side caliper just so everything will be new. But it stops straight now with a new brake job, pass caliper and hose on. However, this other problem has been ongoing and it does it on my 1998 Ranger too. It's not the heater core.
I think the evaporator case is filling with water and dripping down under the carpet. So the drain tube must be stopped or the case must have a bunch of leaves stopping it up. But where is this tube you're suppose to check? I don't see a conventional drain tube I only see a blower motor vent tube that doesn't drain to the outside of the car anywhere. I know my 73 Charger has a rubber drain tube that comes out of the evaporator case and drains onto the ground. But where is this one on a Ranger or what else could it be? It's only the passenger side so it's got to be that.
Ford Ranger / B-Series :: Water On Floor Of Cab After Heavy Rain
When we have a heavy rain water leaks in on both sides saturating the floor board.
View 2 RepliesFord Ranger / B-Series :: Clutch Pedal Went Almost To The Floor Before Disengaging
1997 Ford Ranger w/manual 5 speed tranny
A few weeks back my clutch pedal seemed a bit softer than usual one day. Still it worked fine... no problems shifting. Today after a short ride it went almost to the floor before disengaging. Now I cannot get it in gear without grinding.
So cold out I'm not sure I want to tackle this right now, what to look for and where?
Ford Ranger / B-Series :: Passenger Middle Of Floor Wet When Raining
I haven't ever been able to figure out why the middle of my passenger floor board gets wet when it rains or I go through a carwash. It's definitely not a heater core leaking. I don't see or feel any moisture under the seats further back or further up near the cowl, or roof. It's exactly in the middle of the passenger floor. Is there a plug under there? I've yet to pull back the carpet to look. I plan on eventually replacing the carpet but I want to figure out what the water is. It gets a musty smell because of the water. It's not a lot of water, not a puddle, just you can lift up the floor mat and see the moisture on it. So it's under the carpet. Windshield was replaced 3 or 4 years ago.
View 6 RepliesFord Ranger / B-Series :: 2004 - Clutch Pedal Went To The Floor
My buddy called and said his clutch pedal went to the floor on his 04 4.0 ranger. Said no fluid leaks or anything, so I suspect the slave cylinder went. He said the slave is on the inside of the trans and you gotta pull the trans to do the slave, so might as well do the clutch too. How hard is it to replace both these on this truck? I've done it on a 94 cummins, so the trans should be a lot lighter. just wondering how bad of a job it is to do?
View 2 RepliesFord Ranger / B-Series :: Clutch Pedal Will Not Go To The Floor And Therefore Truck Won't Start
Installed a new clutch and slave today. Kept the same master cylinder.
The problem I am having is that the clutch pedal will not go to the floor, and therefore the truck won't start. The slave is moving back and forth roughly 3/8 inch, maybe more. I am pretty confident that there is no air in the system.
If I loosen the pressure plate a little, the clutch will go to the floor. But tighten it back up, and it again only goes down about 75%. This is a late '95 so it has the self adjusting clutch. I did get the correct kit for it, as well as slave. It's like the self adjusting part is too far adjusted and won't let my slave travel as far as needed.
In troubleshooting, I did notice that I failed to get the dowels in the flywheel aligned in the pressure plate. I am old school and not used to dowels in the flywheel! The dowels are not hitting anything and are not preventing the pressure plate from seating on the flywheel. But it is something I'm going to fix if I have to pull the trans again.
For reference, I replaced the clutch because the slave cylinder was hanging up and preventing the clutch from getting fully released. Aka clutch slipping.
Ford Ranger / B-Series :: 2008 - Foul Smell From Floor Vents?
in my 2008 ford Ranger Sport with a V6. The smell reminds me of one winter when I had stepped in dog and didn't know it until I was four miles down the road and the heater was on full blast. The smell floods the cabin when the heater is first turned on and warms up, but dissipates after a while. (And I don't have dog on the floor boards or on my boots.)
The smell does not come out the AC vents or when the AC was operated this past summer.
Ford Ranger / B-Series :: 2003 - Brake Pedal Goes To Floor - ABS Sensor?
acts like abs sensors could be bad. but the brake pedal goes almost to the floor, after it does it's pulsating. But the abs light does not come on. I already changed brake booster, no change!
View 5 RepliesCamry :: Rumbling Noise With The Vibration Continues With Driving
2006 camry LE - 4cyl - 140k miles
[URL]....................
The car idles pretty rough & loud but ive noticed its only when im in 'drive' with my foot on the brake, at stop signs/lights. Its also much worse when the engine is cold. It settles right down if I come to the stop and shift into 'park'. So as I roll to a stop and hold the car in place with the brake the engine starts vibrating.
I dont know much about these things but it almost feels like i'm restricting it by having my foot on the brake and the engine wants more gas or air or something (could be way off base, but thats how i perceive it)
The RPMs sit around 1,000 and as the engine idles/rumbles it gets up to maybe 1,200-1,400 RPMs which i didn't think was significant but im pretty new to this.
Forgot to mention the most important thing- there is a rumbling noise that goes along with the vibrating, again only while stopped, goes away immediately when i pull off the brake and hit the gas.
Ford Super Duty (1999-2016) :: Strong Vibration Like Shuddering / Growling And Rumbling In 2WD Intermittently
My 2000 f250 4x4 V10 5spd manual with LSD and 63k mi gets an intermittent but very strong vibration like a shuddering, growling, rumbling in 2WD. The 1st time it only lasted about 1 second. It had been making a swooshing noise that sounded like front left wheel bearing for several thousand miles before this, so i replaced bearing assembly even though it turned smoothly.
After that, It still made the exact same swooshing noise and after a couple miles at 45mph, it had the strong vibration/shudder that lasted about 3 seconds. I stopped and locked the hubs manually. The vibration happened again in a couple miles, so seems like it's not the needle bearings in front stub shafts or locking hubs. On that last occurrence, the vibe went on for 5 seconds, felt the same with clutch in, and went away only after truck slowed down to nearly a stop. I've driven it about 6 mi total since the 1st occurrence.
Front right Wheel bearings feel smooth. I unbolted the driveshaft support bearing and it spins smoothly. The front u-joint maybe had a tiny bit of play, all bolts tight. I didn't check the nuts for yokes, but it didn't look like yokes had any play. Drive shaft slip joint moves smoothly. No up-down play at pinion shaft input into rear diff and output from transfer case. Rear diff oil was full with a little bit of silvery sludge on the magnetic filler plug, maybe 1/10 of a cc, no metals slivers or chunks. I raised the rear wheels and ran 5th gear 2WD at idle (~30mph) and touched a 4' listening stick to the drivetrain components.
The only odd sounds were from the rear differential. It sounded like a bad bearing with random crunches and thuds mixed in with the normal whirring. Crunches and thuds were loudest at front of diff housing. I blocked one wheel and repeated in 3rd gear. You could hear noise like gears meshing (noisy spider gears? maybe was LSD clutches?). The differential was warm after 5-10 minutes, with the hottest area being about 3" from the front of diff, just before the housing widens.
So, I'm guessing the pinion bearing is bad and the intermittent shudder is the bearing race spinning in the case when bearing seizes.
Ford Ranger / B-Series :: 2000 - Water Leak On Passenger Side Floor
2000 ford ranger, 2.5 2wd
Been having a little problem whenever it rains, the carpet on the passenger side gets soaked through and I'm not really sure where the leak is coming from. the only part of the floor that gets wet is the flat part where the passenger would put their feet, but the parts that slope up towards the dash and towards the middle of the cab stay dry. I've pulled up this part of the carpet, and the rubber grommets are intact and in good shape, and there is no rust or anything on the floorboard. from searching here it seems people have had similar problems, one thing being a leak into the seals around the third brake light above the rear window.
a couple things i should mention is that the air conditioning condenser has been broken for about two years, so could water get blocked up and leak in? since its winter here in PA i haven't used the air con since last summer though. I'm not really sure how long the leak has been happening since I've always kept a floor mat over that spot, and the carpet drys in a few days anyway.
Another thing i should mention is that the weather stripping at the bottom of the window on the drivers side door is not perfectly tight and tends to come out of place when the door is closed hard. this has been happening since i got the truck almost three years ago and a new piece was just put in a month ago (the leak had been occurring before the new piece was installed) when the truck was hit and went in for body work. possibly a drain routing to passenger floor? I should add that I'm sure it's not coolant, it has no odor and feels like water.
Might be a good idea to pull up the whole carpet on passenger's side and sit in the cab during the next storm...
Ford Ranger / B-Series :: 1992 - Passenger Side Rubber Floor Mat Has A Puddle Of Water After Rain
Whenever it rains a substantial amount, like all day I go out to my 92 Ranger and get in and notice the passenger side rubber floor mat has a puddle of water on it. I look under the floor mat and only the center of the carpet there is wet. I see it's getting the edge of that side of the headliner wet and ruining the new headliner had redone. I didn't realize there was water leaking until I got my headliner redone and put back in. It very well could have been leaking causing the headliner cloth to all tear. It's wet along the top passenger side where the grab handle is and the plastic trim. I thought it was the rain gutter on top of the roof so I put in some black silicone and some of it stopped but not all.
So I thought it was still leaking at the front corner so I put more silicone in. Don't know yet if that was what it was for sure but I'll find out tomorrow because it's raining pretty good right now. But just in case where else could it be getting this much water in. If you go through a carwash, or hose it down for awhile, or even drive while it's raining bad it won't get water inside. I'm not convinced it's the rain channel 100% because on the driver's side the putty filling the rain channel on the roof looks worse than the passenger side and there's no water coming in on the driver's side. There is no water coming in the back or on the back carpet or headliner.
I don't see any evidence around the windshield. I can't understand why only the middle of the passenger side carpet is soaked and not the top or under the seat, unless it's just soaking through the rubber floor mat and not drying out. It's getting so frustrating because I can't visibly find any evidence, I have to wait until it rains and then I can't see why it happens. It's ruining my carpet and my new headliner. I want to replace the carpet but want the leak stopped first. Where are common trouble areas on these 92 Rangers for water leakage?