Ford Ranger / B-Series :: 1940 Pickup - Upgrading To Power Brakes
I have my 1940 Ford pickup on an 86 Ranger chassis. I'm finally to the point where I can drive the truck a little (still not running right) and I'm thinking about upgrading to power brakes. I have used the entire braking system from the Ranger in this build. What's involved in upgrading? Right now, there's a standard Ranger master cylinder hung on the firewall and attached to a Ranger pedal hanger assembly on the other side of the firewall, so I have all Ford parts to interface with. Also, what is the diameter of the booster and how deep is it from front to back and will the upgrade require a different master cylinder?
View 3 RepliesFord - Ranger :: High Idle - Pickup Occasionally Go Into Over Drive When It Is Not In Gear
For about 6 months my 95 ford ranger 2WD 4 cylinder pick up has occasionally gone into "over drive" when it is not in gear the idle will get crazy high, like one of those party toys that yo blow into and it spins an makes noise. Once put into gear it calms down but it has more forward motion without gas than before. If it gets really bad at stop lights I will turn it off and turn it back on. It may still do it when I turn it back on but by then I will be putting it in gear. When it is in this condition and I turn it off it takes longer to turn off, like it is winding down.
I would say that this happens every 4th time it is drive, sometimes less sometimes more. There seems to be no rhythm. I took it to an electrical specialist and they could not find anything, and last week the check engine light came on so I took it to our normal mechanic. They did a test and found that the engine speed limiter had been reached which was why the check engine light came on and also pretty scary. The diagnostic codes were P0500 and P1270. I am worried 1. that this is making the care unsafe to drive even though it seems like we can manage it to a degree and 2. that is is doing damage to the car by putting it in such a hyper work mode.
Ford Ranger / B-Series :: 1990 - Starting And Dying / Ticking In The Engine Compartment
I'm having a rough go with my little 1990 Ranger Custom. Let me get into the signs and symptoms I'm finding, The Truck is having starting and dying issues. It has plenty of Gas. It is completely erratic when it dies. I'll be driving along and suddenly, as if turning the key off, it dies. No sputtering of the motor, no clicking or clacking or growling anywhere. Just a clean sounding turn off. The odd thing is, I'll leave it for a few hours, and the problem disappears. I can drive it for one to 30 minutes and then it can die again.
Now it's sitting in my driveway I am rough on the truck, because its a work truck that I use to drive down to my job site. So, farm pasture, fields, woodland paths and tractor access roads. I checked to see if the pump plug was unplugged. But it's very plugged in. The entire fuel system is just less than a year old, and I am very good friends with the old owner and he can't figure it out either. Could I be having ignition problems? There is a ticking in the engine compartment that isn't very noticeable, only noticeable when the hood is up and motor running, but that has always been there since I've had it. I heard that sometimes the safety switch on the firewall turns off the fuel system in case of accident.
Could that have gotten agitated? I've been having this issue for a little while, after I drove it in the rain for an hour and half. It was pouring rain. I ran out of gas the day after (because my fuel gauge doesn't work) and I used a Jerry can filled with gas to get it to the gas station. I didn't sift the gas, but I don't see it having debris either. Could I have water in the system? I put injector cleaner in my tank and more gas to try and dilute the system but, that doesn't seem to have worked...
Ford Ranger / B-Series :: 1987 - Misfiring - Run Rough - Loss Of Power - Dying
My brother's 87 ford ranger 2.3L truck began to have problems. It would be running great, then start to misfire, run rough, sputter, shake and loose accelleration then die. Then it wouldn't start back up for a long time, sometimes til the next day. Little by little, the truck would drive a shorter and shorter distance between breakdowns. He first tried some minor work himself, (basic tune up) - replaced his rotor, cap, plugs, air filter, fuel filter, but that didn't fix it. He went to one garage (big mistake), who said the fuel pump pressure was fine but said he found a broken wire on the harness grounding out and it needed new ignition module and replaced it. (Cost was $350.00+), Garage promised to honor any additional work nec if it continued to have the same problem, and would be free of charge.
Five more breakdowns later and two more "better quality ignition modules", new battery terminals, and 1 new computer later, this joker did more unauthorized work and demanded another $200+ besides the fact of breaking his orig agreement "free of charge" if any further problems! Needless to say, second garage fixed the truck by replacing the magnetic pickup, part # DU 30-C (an electrical part that goes in the distributor and pulsates a current to operate the timing) (it does something like that) and the truck has been driven approximately 40-60 miles as of today, (3 days later), without breaking down. All the other times when picked up from incompetent garage, it wouldn't go more than 1 - 7 miles before breaking down and each time they didn't fix it.
Ford Ranger / B-Series :: 1999 - High Idle - ECM?
I have a 99 Ranger w/3.0. It idles about 1500 rpm cold,and 1200 warm. Here are the things that I have tried.
1.Checked ALL vacumn hoses/lines
2.Changed Air idle control sensor
3.Throttle position sensor
4.removed and completely cleaned throttle plate in throttle body.
5. removed top of intake manifold and checked for cracks and/or leaky gasket.
Nothing seems to change. Could it be a faulty ecm?
Ford Ranger / B-Series :: 1999 - Stalls In Hot Weather / Low Idle Otherwise
I have had my '99 Ranger since 2002. Since it has started getting hot in Texas, the truck has decided to stall at horrible times. When driving on the interstate, there is no problem, but as soon as I get in town and have to let off the gas to turn or stop, the whole truck dies. Unless it sits for a long time, it will continue to die at every stop. It is harder to start each time. I have changed the fuel filter and added STP to the last tank of gas. Also, it is tough to start and keep running until it has warmed up on any day. I have to sit in the truck and keep the idle up so it won't die.
View 1 RepliesFord Ranger / B-Series :: 1999 - Shaking When At Idle In Gear
I just got a 99 2.5 rwd auto and it shakes when it's at idle in gear. I'm pretty sure its because the AC pulley is engaging drawing power. I was thinking about turning the idle screw up a blonde-one because when I hold the brake and give it slight gas it goes away.
View 3 RepliesFord Ranger / B-Series :: 1999 - Stutters While Idle - Worse In O/D At 45 Mph?
My truck is stuttering while idle and gets worse once it's in OD. My Check engine light is not on(yes it works). How to diagnose the problem. I don't know whether the plugs need changed, wires, fuel pump..
View 1 RepliesFord Ranger / B-Series :: 2003 - Valve Cover Leak / Exhaust Smell Then Started Bogging / Dying And Shaking
I have a 2003 ford ranger 2.3 vin d 5 speed, this truck originally... Took it in for wires plugs front brakes fuel filter battery and added a small cold air intake. We discovered a valve cover leak and while repairing guy drops a screw into a valve and when finished he started it lodged the screw between the valve, shearing off a cam sprocket bolt. Throwing the timing. 2 valves on the exhaust side were bent and replaced. no damage to the head.
Timing was reset and the truck was running. 2 days later truck is running/had a hint of exhaust smell then started bogging dying and shaking, at which time we got an 02 bank2 lean code and fixed that. it cleared code and didn't fix it. From there we replaced coil, imrc intake bc of a crack, tried and check all vacuum, reset the timing. Timing would slip before but no longer than 10 minutes every time truck started.
Found the hole in the timing cover that holds the bolt to torque? to harmonic balancer was broke. replaced along with the diamond washers and cam sprocket bolts. timing finally held crank sensor was adjusted. truck came home for one day running good, we had removed the cold air intake and replaced the factory air intake. next day it was so slow outta first gear, you must baby the throttle, if you floor It, it sputters and kinda pops, truck stays slow all the way to about 10 mph and 2000rpm then it begins grabbing speed, 3000rpm is where this truck shifts the best, 2nd is better, third better than that.
As rpm increase the truck runs better, it idles steady at 1100-1200rpm at stops with an audible miss and then struggles again on takeoff. Here what im wondering, the truck has an abs sensor that just came on, but no codes showing now.tomorrow I wil run matko determinator 3.0 on it. and test the catalytic converter. first how do I check the timing belt to see if it stretched? do these trucks store the p.i.d.s. koer or kams that could cause one, all, or any of this and if so do I have to have it flashed from ford or can you manually do this without a drive cycle test.
Ford Ranger / B-Series :: 1999 - Crank But No Start / 3200 Rpm At Idle
1999 mazda B4000 4WD 178000 miles 5 speed manual, I've been having a crank no start problem but after a few tries it would start, a week or so ago it was really cold (23) it wouldn't start so I opened the air box and shot it with starting fluid it took about 5 long sprays but it started.
It ran up op 3200 rpms and won't go back down, took it to my shade tree mech. he hooked it up to the diagnose thing it showed no codes, he poured water over the motor it different places and toward the back it idled down for a second so he says "blown intake gasket' so we replace upper and lower and sure enough we could see where there was a bad spot on the upper and a cleaner spot on the port.
That was not the problem it still idles at 3200, I mean wide open screaming, could the starting fluid have done something? Now he says "blown head gasket" I never had any idle problems before matter a fact besides the hard starting problem that started it was running just fine, what happened?
Ford Ranger / B-Series :: 1999 - At Start Up No Idle - Brakes Too Sensitive?
My manual 5 speed 99' 2WD 2.5L Ranger is starting to have some small problems here and there. My main concern is when I start the vehicle sometimes, there is no idle. The vehicle will turn over and if I do not hold the gas pedal down it will die immediately after about 2 seconds.
If I hold the gas down so the RPM's stay up (Around 700 RPM's or so, something just a little above 0 to keep it from dying) after about a minute, sometimes few minutes the idle will kick in and I do not need to hold my foot on the gas pedal to keep the truck from dying.
This is about all I know from the problem besides that it does not matter how long my truck is sitting. For example, my truck was sitting for 5 days and I came home and started it up just fine, but after I drove it a few minutes later and stopped driving, when I went to drive it about an hour later the symptoms came back again.
Also, My brakes are acting a little funny. I went through when I first got the vehicle and bled the brakes, took the front rotors in to auto zone or another shop and had them fixed up, and new brake pads. Sometimes when I first start driving the brakes are extremely sensitive, to the point where I apply a little bit of pressure and my truck will start skidding. This goes away after driving for a little bit though.
Ford Ranger / B-Series :: 1999 - Rough And High Idle At 850 RPMs
1999 B3000 with a 3.0. The truck idles at 850rpms. When it starts it idles at around 1000 and runs very rough. When I disconnect the IAC the engine dies. The AC also has problems it blows cold at idle but at highway speeds after 7-8 minutes running the compressor kicks out. One can turn it off and it blows cold again after a few minutes.
View 5 RepliesFord Ranger / B-Series :: 1999 - Stalls / Rough Idle And Engine Dies
I have a 1999 B4000 4.0L with 160K miles on it. Bought the truck new. Up until about a year ago it ran perfect but has developed an idle, stalling and occassional jerky ride problem. It occurs at any temperature, engine hot or cold, A/C clutch on or off and in Park, Drive or Neutral. When you start the engine it will not idle unless you keep your foot on the gas. The idle speed will drop to 200-300 rpm and the engine dies. Sometimes you can barely tap the gas pedal and the rpm will shoot up to normal idle speed (about 900 rpm) and stay there a few seconds then begin to drop again. If the engine is cold it will often die a couple times after starting even with the foot on the gas and then about the 2nd or 3rd time run with your foot on the gas.
At stop signs and red lights you have to keep your foot on the gas to keep it running. If you are approaching a stop sign and take your foot off the gas to coast to a stop and brake, the engine rpm will drop and the engine will die. It always starts fine though. Once you are driving it generally runs just fine at low or high speed. You can generally set the cruise control on the expressway and cruise right on. However, sometimes all of a sudden the truck will start bucking and jumping as if it has a terrible misfire. It usually lasts a few seconds and quits. Often if you step on the gas it quits. Even less occasionally the engine will begin to slow as if it is starved for fuel and slow down. You can press the pedal to the floor and it sputters a bit then picks up and runs fine.
I have read about all the threads in this forum and others and tried some of the suggested fixes but it still has the problem. I have tuned it up with new plugs, wires, fuel filter, air filter and PCV valve. Based on some of the forums advice I have replaced the IAC valve, the EGR valve and EGR Pressure Feedback Sensor, and cleaned and inspected the MAF sensor with MAF cleaner. I have checked all my vacuum lines and no leaks there and checked the engine timing which is fine. Fuel rail pressure and engine compression are also fine. Spark plugs show no clues, exhaust is clean and the engine uses virtually no oil. There has been no tear down on the engine like removing the heads, cam, timing gears or any of that and the engine is completely stock.
It shows no codes related to the problem. Two or three months after the problem started I showed a code that indicated an injector problem, traced the problem to a bad injector, replaced the faulty injector and it was fine. That took care of that code but didn't solve the idle problem. In my younger days I was into drag racing and I rebuilt engines, swapped transmissions, etc. and still do my own tune-ups today so I am fairly familiar with auto repair and have most of the tools for testing newer cars but this one stumps me. As a last resort I'm about to take it to the dealer.
Ford Ranger / B-Series :: 1999 Mazda B3000 V6 Started To Stall Whenever In Idle
I have a 99 Mazda b3000 v6 that has recently started to stall whenever in idle. Check engine light is on and the following codes popped up (P0176, P0135,P0141, and P0155). I'm sure one of these codes has to be related to the problem but I am clueless when it comes to troubleshooting. Also it started stalling after I filled up the tank. Not sure if that has anything to do with it, check engine light was already on before that.
View 2 RepliesFord Ranger / B-Series :: 1990 - CEL Only On At Idle
I recently acquired a 4.0 Ranger 4X4 Auto for my use in Costa Rica. It runs fine but it'll illuminate the CEL within a few seconds of starting and whenever revs fall below approx 1000. When pulling off the line or accelerating, the light will go out but comes back on when the throttle closes. The previous owner has replaced the MAF and idle air valve. I've corrected a lot of issues with the vacuum system and think it's back where it ought to be. I know I am going to need to pull the codes but I'm back in Dallas now and can't do it yet. Need general list of affected parts that I could buy here and take back down.
View 14 RepliesFord Ranger / B-Series :: AC Compressor Turning On And Off When At Idle
When I am at idle, the compressor keeps turning on and off every few seconds. It seems to work fine while driving. What do I need to do to fix this?
View 14 RepliesFord Ranger / B-Series :: IAC Open Up And Raise The Idle
My 04 ranger is back at it AGAIN. It started about 3 years ago.
- Cruising along on the highway and then come into town. Idles at 2000 RPM
- Shut it off. and restart it. Again, 2000 RPM.
- Shut it off and it idles normal
- Drive it 2-3 day and then it idles high again
- I have clean and functioned the IAC and it works fine
- Cleaned throttle body and I never can get it to stick.
- Replaced throttle cable
It still was idling high
- Replaced ECM and it idled normal for about 1 year
- Replaced em again and it idled normal for about 6 months
It is back at it again. For what ever reason the EM is telling the IAC to open up and raise the idle...
Ford Ranger / B-Series :: Strange Sounds At Idle?
Allright, I seem to be having these very strange sounds at idle. Mostly when I am in Drive and waiting at a red light. In Park, it isn't as bad it seems.
One sound is knocking. A kinda slow one and irregular. Not a motor knock tho. Doesn't sound like that. It also kinda clicks from under. So, those both sounds come from under or the sides of the truck.
Should I worry about this? I've had these sounds since I've got the truck. Sometimes louder than usuall.
Ford Ranger / B-Series :: 1988 - Won't Idle - Starts Right Away Then Die?
88 ranger. 2.9L manual. Just bought this truck. It ran great when I bought it. After a day or 2 it would idle rough. Almost die but it wouldn't. No check engine light. It seemed to do this intermittently. Some times I'd start it and it be fine. Other times I'd start it and I'd expect it to die at each stop light.
Now for the last couple days it dies on every start up. It won't idle. It'll start right away and then die. I can keep it going by keeping the engine rev'd but the check engine light is one. If I keep it running and start driving down the road it'll drive with the check engine light on for about 5 minutes. Then the light goes out and it runs like normal, even at idle, until I shut it off. Then it's the same story at next start whether it's right after I shut it off or hours later.
It doesn't seem to matter whether the engine is hot or cold. When the check engine light is out, it runs great the rest of the time whether at speed or at idle. To me it sounds like a sensor is on it way out. I figure if it was vacuum, it happen at every idle, and if it was fuel it happen all the time or at least every idle. Tried to get a code at parts store but the reader wouldn't work. It couldn't tell it was plugged in the the truck for some reason.