Ford Ranger / B-Series :: 1998 - Horrendous Shake Upon Startup
I have a 98 Explorer upon startup is horrendously shakes. What went to hell in the transmission?
View 6 RepliesFord Ranger / B-Series :: 1998 - Missing On One Cylinder During Cold Startup
1998 4.0 ... She only misses about 30 seconds during stone cold startup. I figure it's probably the plug thats hardest to reach ? Isn't that the way it always is? From the hood I can see only one spark plug, so I figure I'll do all the plugs. Is there any right or wrong approach to the plugs? I did the thermostat today, but this plug job looks like it's gonna be a bitch. Time for some skinned knuckles Next is the right side O2 sensor, that looks like fun too. But I gotta say, this little truck is sweet. Great visibility and easy to park in the city. I really like her. She's a keeper. She needs some new sway bar bushings too, but no surprise with 127 K on the clock.
View 5 RepliesFord Ranger / B-Series :: 1993 - Won't Go Past 35 MPH And Shakes?
Today on my way to work my 1993 ford ranger would shift fine but would refuse to go over 35mph and shook pretty bad. I don't know where to start...
View 6 RepliesFord Ranger / B-Series :: 2002 - Trans Hesitates - Shakes At 65 - 70 MPH?
02 ranger 4.0 v6 auto has 110000 miles on it. at highway speeds 65-70mph feels like it strugles to shift, truck will shake and bounce some. when this happens rpm's jump from about 2200 to 3000-3200 after a little bouncing rpms drop to normal. issue seems to be the worst going up hill but will happen every time i hit 65-70. Also the truck will not bounce or shake with the OD turned off and seems to run fine this way.
tranny fluid/ filter just replaced with no change. new plugs and wires
Ford Ranger / B-Series :: 1999 - Shakes When Idling And Driving
My 1999 ford ranger, when started, shakes and then while i am driving. my check engine light is on and reads a #3 cylinder misfire. I have taken it somewhere to get it checked out and they can't figure out what is wrong with it. this problem only happens 50% of the time. I don't know what to do. Also just got a tune up.
View 14 RepliesFord Ranger / B-Series :: 1996 XLT - Rear End Shakes When Driving Down The Road
My problem is wih my 1996 Ford Ranger XLT 6Cyl. 4.0L 2WD Recntly it started shaking violently in the rear as I drive down the road any road. Mainly slow to about 50MPH or slower, it just starts to shake really hard and then it stops then out of the blue it will do it again I thought it might be the back Drums maybe the shoes came apart and were catching but they are fine everything looks fine, could it be the gearbox on the axle? I don't know...
View 5 RepliesFord - Ranger :: 1998 Truck Spits And Sputters On Startup
Truck spits and sputters when it starts up..and now it does it more often New spark plugs, new fuel pump and filter New mass air flow. I changed fuel octain and that work for a few weeks and back it spits...... It seems that when I put something new in the truck it runs great for a few weeks and then it starts up again...... I can not find a fuel regulator that fits the one that is on the truck now......so I have not replaced it........
View 4 RepliesFord Ranger / B-Series :: Idle Surge On Startup
On startup, hot or cold, I get an initial high idle, up to around 1800 rpm's. This happens immediately when engine starts, and then idles right down. This has done this since new in '04. Dealer at that time said it was normal and not to worry. It's always made me wonder, but I trusted the dealer. Ya, not always smart.
After 92k miles. Engine runs fine otherwise, but I don't really care for grabbing a bunch of rpm's on any engine without having the oil pressure up to normal.
A few weeks ago, I started it up, and some yahoo said he knew I drove big trucks by the way I started my Ranger. That was one of those times. I'm thinking IAC is wide open maybe?
Ford Ranger / B-Series :: 1995 - Periodic Rough Idle When Warm / Shakes And Misses
My 95 4.0 has had a periodic idle issue for quite a while. It seems it may be getting worse. Here is when it may only happen:
Vehicle is fully warm. I shut it off for about 1 hr or so and when I restart it, it shakes and misses in idle. It will idle fine after I drive it around or if I rev the engine for a while when still parked.
This never triggers the "check engine light". New fuel filter, plugs and wires.
Ford Ranger / B-Series :: 1993 - Shakes Really Bad And Lost Power After Replacement Of Brake Caliper?
My left brake caliper locks up on me. I have replace it, the brakes , and the wheel bearings. when im driving down the highway and go between 45 -55 my front end shakes really bad and i start to lose power.
View 8 RepliesFord Ranger / B-Series :: Oil Pressure Goes Up To About The Middle Of Gauge After Startup
I have a 97 Splash with the 3.0, oil pressure goes up to about the middle of the gauge after startup, however, it stays there whatever I do, warm/cold, idle/5500 rpm. Is it supposed to be like that?
View 4 RepliesFord Ranger / B-Series :: 1985 - Chattering At Startup Which Quickly Went Away After Warmed Up
My ranger has always run pretty good except for a small bit of chattering at startup which quickly went away after it warmed up. Now all of a sudden its much louder and doesnt seem to go away while driving. I read about the oil pickup tube getting blocked and not properly delivering oil and so I performed the superhuman task of dropping the oil pan to check. While I couldnt get the oil pan all the way out, I got it to where I could feel the oil pick up screen and everything seems okay. I have the valve cover off. Are the lifters adjustable? Whats the issue?
View 10 RepliesFord Ranger / B-Series :: 1999 - Intermittent Misfire On Startup - No Codes
Previously on "This Old Truck": [URL] ....
Mileage now 298,5xx. Done since last report: Oil change and filter. Trans oil change (merconIII, no leaks apparent). Tires. Front brake pads. Clutch safety switch (was interfering with cruise control operation) Coolant replacement. (see below)
Rat damage related overheat (near total coolant loss, but no MIL) at 288k. (Rat suffered acute lead poisoning later that night) No sign of rodents since.
Fuel filter change (after onset of symptoms).
NO MIL/CEL, no pending codes. CEL/MIL operates on KOST.
Temps normal (190F +/-2 deg during steady-state cruise operation, fuel flows and fuel mileage have not changed significantly. (fuel mileage has IMPROVED approx 5%, possibly due to gentler/slower driving)
M5OD with Limited slip 3.73/ payload pkg II (1650lbs)
Symptoms:
- Intermittent misfire on startup, seems to get better as the truck warms up. (intermittent= some days it do, some days it don't.)
- Truck starts and idles well, even with misfire.
- Intermittent loss of power, usually worse on days when no- or minor- misfire at startup/cold idle. From the driver seat it feels like accelerating over painted lines on a rainy day. . . a couple revs of no power, then it pulls hard for a second or two, then misses a couple of shots, lather, rinse, repeat.
- Usually worse in higher gears; (not noticeable in first or 2nd, bad in 3rd at high power settings, now almost constant in 5th, to the point that truck will not accelerate below 3000rpm in 5th even on flat ground.)
- Fuel flows above 4GPH/ OBDII "LOD" (engine load) reported above 75% are typical during malfunction. (Fuel flows have been as high as 9GPH with no problems on other days.)
Symptoms started at approx 292k and have been slowly getting worse over the past few months. . . . usually worse at beginning of trip, fading to very occasional after 50 miles of high-speed driving. Some days/trips no noticeable malfunction.
Thoughts:
1) Ignition wires tired? (did visual inspection, no obvious damage, but no water spray test performed, but seems likely given that the problem is most evident in conditions that would lead to high cylinder pressures.)
2) Fuel pressure? (not measured yet. . . original pump but possibility discounted due to intermittent nature of malfunction.)
3) O2 sensors tired/rat damage? (Original units still installed/ no obvious damage on cursory visual inspection under truck)
4) Injector going bad or injector wiring rat damage?
5) Plugged catalytic converters? (no sound of blown exhaust gaskets, exhaust flows well at tailpipe, with puffs at misfire.)
6) Cam sensor? (never been replaced; known issue with this model engine. Had intermittent mystery squeak that came and went at approx 250k-260k)
7) Clutch slipping? (never had one do that; always lose the throw-out first)
8) LSD problem? (fluid level/ appearance ok, last changed 150k; would expect worse in LOW gears)
9) Blown head gasket/s?
10) Cracked heads/ block? (Oil and coolant levels and appearance normal)
So: That's the plan of attack. What am I missing? (Clutch last done approx 170k; burned throw-out, did disk, flywheel, pressure plate, slave cylinder while the trans was down. I did not open the hydraulics or disturb the pedal linkage when I replaced the safety switch. )
Ford Ranger / B-Series :: 1993 - Fuel Pump Relay Blown Only At Startup
I've been driving 93 ranger 3.0 4wd since last fall. first week I went to start and fuel pump relay had blown. I put a new one in and been driving since fine, till today. Now when I try to start, if it starts it will run fine all day as long as you don't turn it off. If you turn it off and restart half the times it will pop relay again. My fuel gauge has been stuck on full since I bought it also. I'm wondering if maybe pump has got had to start and drawing too much current...
View 3 RepliesFord Ranger / B-Series :: 1998 - MPH To KMH Conversion
My sons 1998 ranger is in mph. Converting on to a kmh dash. There's one at the wreckers and I was wondering is it a direct replacement or is it a computer swap also? What years would work?
View 5 RepliesFord Ranger / B-Series :: 1997 - Rough Idle At Startup / When Rev Up Chugs Real Hard Then Dies
I am currently working on a 97 ranger with a 4cyl and 5 speed. its having some idle issues that i cant seem to pin point, you can start it and it will idle rough then when you rev it up it chugs real hard then dies. used my scan tool and all the sensors are good, fuel pressure is good, good compression, all 8 plugs are firing good and no codes. The other deal that has me a little confused is when I unhook the hose that runs from the air intake tube to the valve cover, I get a lot of vacuum at that port on the valve cover that the hose hooks to. Also when I plug it and pull the dipstick, I get vacuum at the dipstick tube. never seen this before but at the same time I've only messed with very few of these trucks so I don't know whats normal.
View 6 RepliesFord Ranger / B-Series :: 2001 - Airbag Light Blinks For About 1 Minute Upon Startup And Then Stays On Solid?
I have a 2001 Ranger 4.0L 4x4 with 101,000 miles on it. I went to go get in it the other day and the Air Bag Light came on out of the blue. I've drove it some since and it is still on. The light blinks for about 1 minute upon startup and then stays on solid for the remainder of the trip. What would make this come on so suddenly and is there anything I can do/check?
View 3 RepliesFord Ranger / B-Series :: 1998 - Won't Disengage Out Of 3 Gear?
I have a 1998 ford ranger and it will not disengage out of 3 gear. The truck still starts but if you let of the cutch. Of course, It stalls. I'm doing the work myself but where I should start looking.
View 1 RepliesFord Ranger / B-Series :: 1998 - 4.0 OHV Miss Under Load
I have a 98 4x4 with 145k miles and 4.0 OHV. Symptoms are as follows;
Uses ALOT of oil. 1 quart per 230 miles. Burning bad in rear cylinders, some in middle cylinders, none in front cylinders. Screams intake or PCV issues to me, not rings or valves. Never any smoke, not even on startup. No significant leaks. MPG always 18-20mpg.
Slightly rough idle.
Miss under load below 2k rpm. Not a terrible miss, but you can feel it. Has never lit the CEL. I know the CEL is good.
Never loses coolant. No coolant in oil or vice versa. Haven't done compression test, but doesn't seem like they ever tell you much anyway.
This weekend I replaced all intake gaskets, plug wires, cleaned oil residue off and regapped plugs (they are 3 months old), injector orings, and PCV valve. Flushed and burped radiator.
It's too soon to tell on the oil consumption, but I thought the intake gaskets would have cured the rough idle and misfire. The idle IS much better, but still not perfect. But the low rpm load miss is actually worse now. Still no CEL. Could it be storing codes without lighting the CEL? Also, how do you clear codes on these, can you just disconnect battery, or do you have to clear them with a scanner?