Ford Ranger / B-Series :: 2004 Truck Won't Start After Slow Down Or Quick Stop
This has happened 3 times.
1st) pulled quickly over to side of road, shut off truck. It would not start then. Towed it to service station and it started the next morning (with no repair made). I wonder if tow ride dislodged the the blockage in fuel line(?). Always sounds like it's going to turn over, but like not getting fuel.
2nd) Went to leave work, truck wouldn't start. Towed to my mechanic and he replaced fuel pump. Thought it was fixed because it ran fine until just the other day.
3rd) Slowed down to complete stop in heavy traffic and it stalled. Would not restart. Again sounded like it was going to start but didn't seem to be getting fuel. Good samaratins pushed me off road. Had it towed to mechanic. Started the next morning without any repair or service. It's like the tow ride and bumps getting it off the tow truck dislodges what ever is blocking the fuel line.
My mechanic replaced the fuel pump, but I don't think her replaced the fuel filter.
Ford Ranger / B-Series :: 2003 XLT 4.0 Stalling At Stops / Low Idle
My 2003 ranger xlt 4.0 has a stalling problem. The engine light came on in aug and I had it coded at AutoZ and there was a code for the oxy sensor, changed that and didn't work so I took it back. In oct I had it coded and it said the air int temp sensor which i was informed was part of the mas airflow sensor, changed that the beginning of nov, got the computer to reset and it still didn't fix it.
Took that part back and had it coded again a few days later and several codes came up AutoZ code 1732 and the the OEM number to cross for them were: P2195 , P0300 , P0316 , P0174 , P0171 , P2197 . Reset the comp yesterday and as soon as the light came on had them code it again and it came up AutoZ code 1732 OEM # to cross P2195. I guess my next step will be to take it to the dealers to get diagnosed..
Ford Ranger / B-Series :: 1995 Truck Will Not Start With The Key
I have a 95 Ranger with the 2.3L and it is a five speed. I am having a starting issue. I have replaced the ignition switch, clutch position switch, starter relay and had the starter tested. The truck will not start with the key. I can jump across the relay and it starts fine but will not even click with the key.
View 3 RepliesFord Ranger / B-Series :: 1995 - Truck Would Not Start / Starter Locked Up
I have a 95 Ford Ranger 2.3L with a five speed. I recently had a starting issue were I parked the truck, went into a store came back out and the truck wouldn't start. Figured it was the solenoid as I couldn't jump across it to get the truck to start. Replaced the solenoid. Still no go. Found a fuse in the starting circuit blown. Replaced the fuse and got it started and drove home. Next morning, I go to leave for work and the truck would not start. Got a ride to work came home and checked it over and found the starter locked up. I replaced the starter. Truck started for a few days and now I am having problems again.
Here is the problem I am having now. Starter is good. Proved that as I can start the truck by jumping across the starter relay. Checked the solenoid with a voltmeter and it is doing what it is supposed to do when the truck starts normal. Here is where I am scratching my head. I can start the truck sometimes and it starts just fine. Next time I try to start it, the fuse will blow.
Replace the fuse and it might work for a couple of starts and then the fuse will blow again. I jumped pass the fuse with a piece of wire for diagnostic purposes. Out of 20 starts, it only started normally 4 or 5 times. I have checked every wire I can see under the dash and have not found any obvious issues. I am at a point where I am so frustrated that I just want to push this 400k mile truck into the back forty and put it out of its misery like a lame horse.
Ford Ranger / B-Series :: 1993 - 4x4 Not Engaging / Grind Just For A Quick Sec When Shifting
So went today and bought a 1993 ranger 4x4 ext cab 4.0! Runs good some bad handy work that i need to fix but truck has plenty of power and good handling...
issue 1- 4x4 not engaging. the light by the push buttons does not come on and you dont hear the "clicking" of the relay trying to engage. so whats the problem and how do i fix it?
issue 2- when clutch is fully depressed and you go to shift (this is only sometimes) you can feel and hear it grind just for a quick sec. and forget about down shifting you cant do that without slowing down. so maybe new clutch?
issue 3- at 65 the vehicle does shake a little otherwise but pretty smooth. any tips on how to smooth it out? maybe new ball joints? tighten some stuff up maybe?
Ford Ranger / B-Series :: 1998 - Clutch Quick Connect Rock Solid?
i i am having trouble getting the quick connect on the slave cylinder to go back in i just pulled the entire transmission and replaced the clutch and now when i try to put the quick connect fitting in the slave it is rock solid and will not go in at all
View 1 RepliesFord Ranger / B-Series :: 1999 - ABS Activates At Slow Stops
I have a 1999 ranger 4x4 , when I'm going to a slow final stop the abs kicks in ,doesn't do it every time , there's no abs warning light , took it to the ford dealer they scanned it and said it was the left front hub & bearing assembly, said the sensor wasn't reading the back of the bearing assembly. I can't understand way the abs light isn't on, is there anyway to clean that they want to replace the hub & bearing, Is a use hub & bearing replacement a good way to go? They told me I could pull the fuse and kill the abs, but I find three fuses I pull aII three and got a speed sensor check engine code. I hate to replace that hub & bearing when there's no problem with the bearing ,Is there any way to deactivate the abs, by the way it's 4 wheel abs.
1999 FORD RANGER 4X4 4.0......
Ford Ranger / B-Series :: 2000 3.0L Running Rough / Shuddering At Stops
I have a recently purchased 2000 ford ranger 4X4 with approx. 130,000 miles on a 3.0L. When I bought the truck, it was running rough while in gear at idle, after first putting it in gear, and when coming to stops, then it quit running all together. I started by replacing plugs, wires, and ignition module. I finally got it to fire up after that, but instantly noticed the tell tale white smoke from the exhaust. Needless to say, my oil looked like chocolate milk. Rather than having the heads machined and checked, I opted to purchase a new set of cylinder heads from Dover cylinder head.
I got those on this week and she fired right up. After a few oil changes to eliminate the residual coolant from the oil passages, she still starts and runs fine, although the idle is a bit rough while in park. When I place it in gear the idle gets a little rougher. After a quick trip down the road, I'm noticing a pretty solid shudder when coming to a stop, almost like it's stuck in 2nd gear, but I can't really tell for sure. Seems to shift fine going up through the gears, but coming down is when the issue is.
I believe I'm dealing with two separate issues, one being the rough idle upon startup that doesn't seem to go away, and two being the rougher idle upon stopping. I've read everything from EGR valve, idle air control valve, low fuel pressure, and a laundry list of other things, and I just don't want to start throwing money away chasing my tail.
Ford - Ranger :: 1993 - Emergency Brake Only Stops Truck From Rolling Forward
My emergency brake works fine when I am parked nose down; it prevents my truck from rolling forward. When I'm parked nose up, the e brake doesn't stop the truck from rolling backwards. 2.3L 1993 ford ranger manual trans.
View 3 RepliesFord Ranger / B-Series :: 2006 - Stalling When Slam On Brakes
Little back story, truck sat up for 2 years. Had 1/2 tank of gas in it that time. I had to do a complete motor swap. I been driving for past couple of days. Had it stall on me while I was waiting on wife to come out of store. Thought it was just bad gas. Today I was heading to town and had to slam on brakes and it started to stall again. It shut off. I cranked it back up and it runs fine till I start slowing down. then it wants to die.
I can keep my foot on gas petal and little and it will stay running. I got to where I was heading and put it in park and it idled fine for a few seconds and then I could hear a whine from the fuel tank. Sounds like the fuel was having a hard time, like it was fighting the pressure build.
Thing is It cranks right back up and drives fine as long as I dont come to quick stop or set idling for a few seconds. I can hear the pump straining, so I am assuming that when I keep my foot on gas a little the pressure is staying lower and not as much is being bypassed and the pump is fine. I think the pump is on its way out but wanted to hear what yall think.
I do have a brand new IAC valve that I bought and did not get a chance to use on the blown motor.
Ford Ranger / B-Series :: 1988 4x4 - Stalling / Cutting Out Sputtering
When I'm driving it starts to cutout (but it never dies) and it won't stop cutting out until I floor it and then it's fine for a little bit and it starts doing it again.
View 1 RepliesFord Ranger / B-Series :: 1998 - Weird Idle At Stops - No Check Engine Lights
I’ve got a 1998 Ranger with 166,000 miles and it’s starting this weird idle at stops where the engine drops about 150 RPM’s and then fluctuates. The problem is intermittent and no pattern as to cold or warm engine. I changed the plugs and wires at 100,000 and the plugs again at 150,000, so the wires have 66,000 and the plugs 16,000. I really don't want to shotgun the plugs, wires and coil pack. I understand that vacuum might have something to do with my problem?
View 14 RepliesFord Ranger / B-Series :: 1999 XLT - Turn Signal Stops Blinking When Brakes Depressed
99 Ranger XLT 4.0 4WD Automatic. With the turn signal blinking and I depress the brake the turn signal stops blinking until I release the brake. Where to start.
View 2 RepliesFord Ranger / B-Series :: 1995 Not Getting Gas When Floored To Pass
1995 Ford 4.0 ... All the following have been replaced on the truck.
High Pressure Fuel Pump and assembly
Idle Air Control Valve
Spark Plugs
Oxygen sensor (Bank 1 sensor 1 Oxygen)
Fuel Filter
The most recent item that I replaced is:
Coil Pack
Spark Plug Wires
Now, with the Coil Pack replacement, the truck drives good, as long as I do not floor it (After it heats up, about 15 minutes). Basically, if I try to pass someone, the truck acts as if it is chocking out, like it is not getting any fuel.
Before replacing the Coil Pack. It would chock out at any given time, rather just barely pressing the gas peddle, or just sitting idle.
I took it to a friends muffler shop, and he stated that it is not the exhaust that is causing the issue. I am at a loss. Is there anything else that I can check?
The truck seems to drive fine, as long as I do not get down on it, and try to take off fast after it heats up. When it is cold, I can take off like a bat out of hell, and it runs like no-ones business.
Ford Ranger / B-Series :: 1995 - Bucks Sometimes When Warmed Up
I have a 95 Ranger that when warmed up completely will buck when I let off of the gas. It is a 5 speed and this problem really only happens in 3rd gear and also have noticed it doesn't happen in 4WD. When the engine is cold and I am driving and let off the gas, the truck coasts smooth as silk and as it warms up, there becomes a louder thump when the gas is let off.
It will not do it all the time and it really only happens in third gear at low RPM's coming to a stop. I can give it gas and it picks right back up normally, so I doubt it is a misfire. Also since the truck is a 95 I do not have any CEL indicators, nor is there even a CEL light built into the dash in the truck. It isn't a huge issue because I am used to it and can drive it accordingly without having a problem.
Ford Ranger / B-Series :: 1995 - CEL Came On - P0340 Code - CPS Bad
I am having an engine issue with my 1995 Ranger with a 2.3L. I have been having a P0340 code that kept appearing after several attempts at resetting the PCM. I gave up and took it to a Ford dealer for diagnostics and they called the CPS bad. They changed it, but the CEL light immediately came on with the code still kept coming up. The service rep. showed me the old sensor, it had a spot on the head of it where it looked like something was rubbing it. I'm assuming it's slightly rubbing on the gear it points to, which is the oil pump gear, correct? The truck runs fine, no performance issues whatsoever. Is it possible my oil pump shaft has developed play in it's shaft, causing this?
View 1 RepliesFord Ranger / B-Series :: 1995 - Top End Knocking Noise
Had the top half of the intake off (2.3L) and fixed some vacuum leaks and replaced a power steering pump. Started truck and it ran funny like missing on one cylinder then cleared up then started making a loud knocking noise and running rough. Assumed that it swallowed something when I had the intake off and it got into a valve or into the cylinder. I pulled the plugs and there are no obvious signs of a problem. I also did a compression test and all 4 were around 150psi.
Put the plugs back in and started it and the same noise was there. Removed the serpent belt just in case it was power steering pump related and the noise was still there when I started the truck. Sounds like something is inside the engine still. Going to get a friends bore scope to check further. I guess I will split the manifold again and run the scope in there. Pending that I may also look down the plug holes with the scope. This is a major bummer. Not what I needed.
Ford Ranger / B-Series :: 1985 - Running Rough - Bogging Out And Stalling
I am fairly new to this stuff but I just got a 85 Ranger 4x4 and its running pretty rough it will be fine then all of a sudden it will bog right out and want to stall so I have to keep my foot planted on the gas and it pops and spudders and eventually runs normal again? Its a 2.8 V6 carb...
View 14 RepliesFord Ranger / B-Series :: 1995 - Would Not Start / No Fuel Pressure
I have a 95 Ranger 2.3 with a manual tranny. In the past I have had problems with this truck not starting do to a bad inertia switch and numerous fuel pumps. A couple of weeks ago I pulled the truck off of the driveway into the street and let it set there for a few hours. When I went to put it back on the driveway it would not start. I got it pushed on the side of the garage. I did my normal routine of doing a pressure check. I had no fuel pressure so I assumed that it was the fuel pump (as usual) so I dropped the tank and changed the pump.
I got it back together and it still wouldn't start. I checked the fuel pressure and the manifold still had 0. So I started my diagnostic. I have power from the fuse to the fuel pump relay. I then checked the wiring at the inertia switch and found that there is no voltage with the key on at the supply side of the inertia wiring. I verified continuity between power distribution block and the inertia switch. I put in a new fuel pump relay and it still has no fuel rail pressure and there still is no electric signal at the inertia switch. Where to go from here?