Ford Ranger / B-Series :: 1989 2.3L Will Crank Just Fine But Not Starting - No Spark
89 2.3l 4x4 will crank just fine but no start. It is getting plenty of fuel. Replaced ignition module,crank sensor,computer, checked all fuses. I've been looking for a broken wire with no luck. Doesn't seem to be getting any power to the coil packs. Truck was not driven very often until a month ago. Started up fine everyday until the no start.
View 10 RepliesFord Ranger / B-Series :: 2001 - Won't Stay Running - Blows Smoke?
My wife got off work tonight and went to start up our 2001 Ranger XLT, it starts, but wont stay running unless she puts the gas pedal down, it is also blowing white smoke from the exhaust and she says it sounds like it is missing, sputters and dies when she takes foot of gas.
No previous symptoms, ran perfect this morning, no loss of power all day, no smoke no sputtering and no check engine light. Any clue as to what it is. I have heard head gasket and O2 sensor.
Ford Ranger / B-Series :: 2001 XLT Won't Stay Running - Shuts Off Without Warning?
Last year I purchased a 2001 Ford Ranger XLT 4x2 V6 3.0L 48,000 miles, in perfect shape. I haven't had any problems until the last 6 months I have noticed the check engine light was on. Ok, while at Valvoline, the checked it and said it was a EGR code and that it might have been just an O2 sensor problem, something minor. So they just shut it off. Well it popped back on and I just figured I'd leave it alone. Maybe a mistake.
6 months later. So driving today the dang thing just quit and shut off? No warning, just everything shut off. It happened 3 more times...Then tonight, driving down the highway it shut off again, no warning? Happened 3 more times, couldn't make it home, called and had it towed to my apartment. $30 bucks later, at least my truck is at home.
So the problem is it won't stay running, and it just shuts off all of a sudden? It starts fine, drives fine, but unbeknownst to me it will just shut off, 1 minute later, 5 minutes later, it doesn't keep a pattern...It could be a million things I guess, but I'm not really able to pin point any exact locations. It's not making any funny noises, nothing fishy, but won't stay running. It's doesn't seem to be hurting for gas, it has 1/2 tank, no gurgling noise...
It's Saturday night and my Girlfriend's and I only transportation....So we have no vehicle until we can get this fixed, given that sunday no one will be open...we're playing it by ear.
Ford Ranger / B-Series :: Jerking In The 3rd Gear And Up When Giving Gas
I have a 2000 ranger 4x4 4.0l ... It starts jerking in the 3rd gear and up and it gets worse as the gears changes... If it in higher rpm it doesn't do it as much I don't know what could be the problem it's been a recurring problem...
View 12 RepliesMercedes - Benz :: 1989 - Car Starts But Won't Stay Running
I have a 89 Mercedes 190e. The car stays running and will drive but after so long starts acting like it's starving for fuel. I have spark and nothing wrong with fuel filter but when tested there was no pressure what's odd is the fuel pump was tested and it works fine all the lines have been cleared I'm stumped what else can I check...
View 13 RepliesFord Ranger / B-Series :: 1989 - No Power At All?
I have been thru everything i can think of except the main ECU on the ranger.
I've replaced the starter as well as the starter solenoid also the ignition switch.
What is happening is there is no power after the main wire to the solenoid from the battery. it doesn't power up anything. I've checked the fusible link and it appears intact. with a test light i can see that i have no power from the ignition itself i guess to tell the solenoid to work. i have noticed that the ignition cylinder is a little loose but what can cause there to be no power at all?
Could it be a bad solenoid?
Ford Ranger / B-Series :: 1989 - Grinding Noise When Let Off Gas
I have a 89 Ranger, 2.3, 2wd, Mazda 5 spd. Last year, 10,000 miles ago, I replaced the clutch, pressure plate, slave cyl, and pilot bearing. Today, it started making a terrible grinding sound/vibration when you let off the gas. The noise is coming from the clutch/transmission area. It is so bad that any amount of "engine braking" sounds terrible and I have to press the clutch in and the noise immediately stops. What to check for?
The only thing I can think of off the cuff is
1) bad pilot bearing,
2) low/no tranny oil. I replaced the oil and put silicone on the known leaky spots while I had the tranny out,
3) Input shaft had some "wobble" in it when I had the tranny out to replace clutch 10,000 miles ago.
This could be it but why would it start 10k miles later?
Ford Ranger / B-Series :: 1989 - Engine Sluggish When Cold
I have an 89 Ranger 2.3l with 255,000 miles on original engine. The engine runs like brand new. I'm just curious as to why it's extremely sluggish when cold. Example, it was 3 degrees this morning and I literally couldn't get over 45 mph for 5-10 mins. Everyone was passing me. No knocks or other strange noises just doesn't have any power. Once warmed up its completely normal. Obviously my '01 4.0 Ranger doesn't do this so I was mainly interested in why? Do they use different metal materials, is engine wore out (obviously it is to an extent), or something else?
View 2 RepliesFord Ranger / B-Series :: 1989 - Proportioning Valve Cleaning?
89 4 wheel drive 2.9 5 speed can it be cleaned or cleared.
View 4 RepliesFord Ranger / B-Series :: 1989 - Disengage Electronic Shift?
I recently acquired a 1989 Ford Ranger midsize pickup with an electronic shift button/console between the visors. I put it in 4WD and the manual does not indicate the procedure to take it out of 4WD. What is the procedure?
View 3 RepliesFord - Ranger :: After Turning Steering Doesn't Want To Return To Center And Stay In The Turn
I have a 1987 ford ranger 4x4 with automatic hubs. My automatic hubs completely destroyed themselves and are being replaced with manuals as soon as this new problem is solved. Initially the truck seemed to go in and out of 4 wheel on the hubs and jumped, snapped and ultimately destroyed the retaining clips in the hub itself so that those gears fell out when wheel was removed. I removed both sides and that stopped, but now when I turn the vehicle, this worse at lower speeds, it doesn't want to return to center and will stay in the turn without much effort to turn back to straight.
The pump seems fine on the power steering system. A mechanic friend of mine told me that my universal and upper and lower ball joints where shot on the front axle, but I feel that this might have more to do with the steering rods etc. The originals have been replaced and I am able to grease them, after doing this it seemed really loose for a bit, then by second day of driving it was back to the usual. I just am looking for some verification before replacing tie rods etc and then eventually the hubs, but winter over so there is less concern right now for that.
Ford Ranger / B-Series :: 1989 - Signs Of Water Leaking Through The Gasket
My 89 2.9 has gotten water in the oil. One year ago I pulled this engine to replace the crank shaft (defective Ford design 1/2 thust bearing created a nasty grove in the crank allowing it to slide back and forth1/4 inch), new bearings, oil pump, timming chain, all seals and gaskets (not head gasket). The engine had great compression so I didn't do any thing more. Now I have a leak. No oil in water. NO compression leaking off into the water jacket. No "steam" coming from the exhaust. I've replace the intake manifold gasket. It showed signs of water leaking through the gasket, actually bubbles of water trapped inside, so I hoped this was it, but I still have water in the oil. I have now removed the intake and driver side head (head gasket shows now sign of leaking). No signs of water in cylinders. Is it possible to have a warped intake manifold? I have removed it twice, and I was told that some V6's need to be slowly removed VIA de-torque the bolts. I didn't do it the first two times I removed it, today I did. I plan to remove the passenger side head tomorrow. I will take the intake down and have it tested for warping. I have read many stories on this web site of the heads getting cracks, but they all seem to be in or near the valves, I assume that allows water to be burned off as a steam engine OR compression being pumped back into the water jacket.
Is there any other source of the leak that I'm missing? Is it possibly my intake? OR should I go ahead and replace the heads?
Ford Ranger / B-Series :: 1989 2.3L - Stubborn Crankshaft Pulley / Not Come Off Easily
Needing to do a timing belt on the Ranger I bought, the crankshaft pulley just feels it needs to be stubborn and not come off easy. I know the front pulley is pushed on and kept in place with a pin, however I think my puller may be too large to fit where it needs to be to pull it off. I want to say I am just pulling an pushing on the same part but not sure. This is my first 4banger vehicle and I have never ran into such a deal even with working on the heavy OTR diesels.
I sprayed things down with Liquid wrench and let it sit while I unloaded and mounted an engine onto a stand last night. I think I might have to buy another puller and reduce the diameter of the pivoting end to fit, which I don't know why Ford would make a pulley on a 4banger engine family different than a 6 or V8 platform. Am I just dealing with a stuck piece?
Ford Ranger / B-Series :: 1989 Automatic Transmission Shifts Hard Into Second
I got this 89 ranger xlt with a 2.9 and automatic transmission. I mainly bought it because it was in such good shape and I was planning on putting a 5.0 in it. everything works on it. the a/c, radio, lights and it runs real nice. the only problem it has is it shifts pretty hard going into second gear. every once in a while it will shift smoothly into second but only like once or twice a day. he said he had recently changed the trans filter and fluid and the fluid does not smell burnt.
View 7 RepliesFord Ranger / B-Series :: 1989 V6 Stalls / Dies / Powerless After Warm Up
I've recently acquired a 1989 ford ranger xlt 2.9L V6 and iv got my elbows deep already..... starts right up and scene its an older truck i let it warm up for a few minutes seems to sound alright so i jump in and take off... well i make it about two blocks and as soon as the truck seems to warm up it starts to sputter and die out... starts back up and idles for a min and i try to take off, but it seems to have NO power and jerks and dies.... so i push to a street parking spot and get situalated start the truck up again and take off only to make it about half a block tell it does the same....
First i think iv run outta gas witch i might of not sure so I walk to station and get three gallons. put in truck and same is happening. so i start kicking myself for not haven any tools with me and i leave tell next day... that night do a little research and get some idea's of what could be the problem'(s) so i start out with things that look like they need tending Badly WIRES, PLUGS, ROTOR, CAP, MAP SENSOR, and now after a whole day in the rain (Northwest BTW) and grease to elbows? 2.9 V6? What step's should i take next?
Ford Ranger / B-Series :: 1989 - Heater Hose Leaking Around Behind The Valve Cover
Found a tee on the heater hose leaks when it warms up. Appears the PO had noticed it but put a hose over it and now is leaking around behind the valve cover. This is a hard plastic line around 5/16. No online parts show it as being available. Is there a fix for this ?
I would bet several others have had this problem as it lays right on top of the flange of the valve cover where I think it would rub a hole pretty quick.
1989 Ranger 4X4 4 cylinder....
Ford Ranger / B-Series :: 1989 - Passenger Side Tail Lights Won't Work?
i have an 89 ford ranger custom and my driver side tail light works just fine but my passenger doesnt work when i mash the brake the passenger side brake light wont come on. the parking lights work, turn signals, and hazards work but the brake light. ive checked the wires and replaced the socket and still the same problem so either theres something in the wires that im missing or i dont know what else. any hints?
View 7 RepliesFord Ranger / B-Series :: 1989 - Tranny Input Shaft Seal Replacement?
I'm replacing my clutch components in my 89 Ranger with an M5OD transmission. While I'm doing it I'm going to replace the input shaft seal on the transmission. I'm looking for the torque specs for the housing that holds the seal.
Also, should there be any play on the input shaft? My transmission has never made any noise but I noticed some slight play in the shaft.
Ford Ranger / B-Series :: 1989 V6 - Engine Hesitation - Loses Speed When Kick Down
My 1989 Ford Ranger 2,9 V6 is acting up like crazy (engine hesitation) after kick down (it has an automatic transmission).
It can run like a charm for days and days and for the longest drives, but if I do a kick down it will start acting up (while both cruising or idling). This is making it almost impossible to drive as it looses speed. Only way to accelerate again is to do another kick down (then it will accelerate smoothly for as long as I keep my foot down), but that is really no solution as it will accelerate way past the speed limits and the mpg is horrible going up and down like that.
A couple of times this problem has seemed to solved itself after a while of engine hesitation but normally it would be acting up for the whole drive. On the other hand it will be okay again the next time I take it out for a drive.
Diagnostics: It has nothing to do with the temperature of the motor as this will happen after a kick down on both a cold or hot engine.
Simple solution so far: Avoid kick down!
What I have done so far: I have changed the spark plugs, the plug wires, the distributor rotor and the distributor cap with no luck.