Ford - Ranger :: 1993 - Cranking Fine But Start After 2 To 3 Tries
I have a 93 Ford ranger that will not start. It was cranking fine. It would take 2 or 3 tries when it was cold but once warmed up it ran fine and would crank right back up until it was cold again. The last 3 or 4 times I drove the truck it fired right up on the 1st try. Then the last time I drove it, it cranked right up and I drove it between 5 and 10 miles. It sat for about an hour and when I tried to crank it, it wouldn't start. At first it sounded like it wanted to but after a few seconds all it would do is turn over.
After about a week of sitting I was able to crank it up again. It fired right up. I let it run for 15 minutes or so turning it off and re-cranking it. About 4 or 5 times. Then the last time I cut it off and tried to crank it back up it wouldn't start again. I replaced the pickup coil in the distributor, cleaned off the rotor button and leads on the distributor cap (they didn't look bad and were working fine before), I checked to see if I was getting spark but Im not getting it from the spark plug wires or directly from the coil wire.
I checked with a test light to see if I was getting power to the coil and distributor from the wiring harnesses. With the key on power is going into both but I'm not getting any arch when I test directly from the coil wire or the spark plug wires. Ive also switched out the relays and tested the coil and starter solenoid on another vehicle and they work fine. My next step I'm thinking about replacing the computer but don't want to spend on a part a can't return if thats not the problem.
Ford - Ranger :: 1993 - Only Start When Fluid Sprayed In Air Intake?
1993 ford ranger 4 CLY 2 WD getting spark gas to injectors will only start when fluid is sprayed in air intake. have replaced fuel pu,p. fuel filter air intake regulator. ran okay till ran out of gas.
View 2 RepliesBuick - Regal :: 1993 - Intermittent Hard Start / Idles Roughly
1993 Buick Regal 3.1l V6 Multiport injection
Problem: The care currently has a hard start, and a fluctuating idle. I bought the car a year and a half ago it still has low miles about 94,000. The care used to start fine but had a fluctuating idle in the range of 750 to 2500 rpm. My brother who is a mechanic and doesn’t live near, do all the gaskets when he visited. Then the idle fluctuation dropped to 750 to 1000rpm, when the car rpms fluctuate there is a whirring sound I can hear from the cab, like a pump or pull system. On occasion there is a vibration as well but it is inconstant and irregular. Fuel pressure seems to fluctuate as well. If the car will not start I give it a little gas and it will run fine after a minute or two, but then the idle starts to fluctuate.
No fuse issues I can tell and relays seem to be fine.Checked for lose wiring connections found, none. I have replaced:
- Hoses and gaskets
- Starter motor
- Battery
- Fuel Pressure regulator
- Fuel Filter
- Spark plugs and wires
- TPS
- Idle Air control Valve
- Crank shaft sensor
- PCV.
Right now I’m thinking it could be the fuel pump (a nightmare to change on this car), a fuel injector failing, and the ignition switch.
Ford Ranger / B-Series :: 1993 - Check Engine Light Comes On And Truck Will Not Start
Sometimes the check engine light comes on and truck will not start, the fuel pump runs non-stop.. when check engine light goes off,the fuel pump runs for a few seconds and stops,truck will start.... driving down the road check engine light will come on and truck runs bad.... 1993 ford ranger .....
View 1 RepliesGeo - Prizm :: 1993 - Intermittent Push To Start / Engine Idle Speed Too High At Times
1993 Geo Prizm, manual transmission: Intermittent failure to start over a two year period, gradually becoming more frequent. The engine turns over every time the key is turned to start the engine, i.e. the starter motor/battery/battery connections work flawlessly. Once started the engine runs flawlessly without misses or shut downs. The only possible problem may be the engine idle speed that seems at times to be too high even after the engine is warmed up. Without predictability, the engine may fail to start when the key is turned.
Remember the engine still turns over normally. It just does not fire up. Two options exist for my predicament. That which is resorted to the most because of the speed of recovery: step out of the vehicle and push start the car by popping the clutch. The other alternative which I have been forced to utilize before because of the physical impossibility of push starting (i.e. if I had been able to push, I would have popped the clutch to start) at the time has been to wait for a protracted period and re-attempt to key start the car. This has been successful a couple of times.
Ford Ranger / B-Series :: 2005 XLT 4.0 - Intermittent No Crank And No Start
I have a 2005 Ranger 4x4 4.0 automatic with an intermittent no crank, no start issue, So the problem has been getting worse over time This time when it wont start, all of the lights work, the radio, the fan, etc. They are all bright and functioning.
The battery is brand new and showing 12.9v at rest. (Yes, I have tried to jump it and charge it to be sure). However, The gauges are not functioning when the key is turned. I have no click, the lights don't dim, nothing happens when I turn the key.
Another neat point, if I turn on a directional with the key on, the relay clicks so rapidly that it won't even flash the lights. I am assuming that it is a ground someplace, but I dont even know where to start on this truck.
Ford Ranger / B-Series :: 1993 - Check Engine Light Comes On And Truck Will Not Start / Fuel Pump Runs Non-stop
Sometimes the check engine light comes on and truck will not start,the fuel pump runs non-stop.. when check engine light goes off,the fuel pump runs for a few seconds and stops,truck will start.... driving down the road check engine light will come on and truck runs bad....
View 2 RepliesFord - Explorer :: 1993 - Intermittent Shake At Highway Speeds
A friend of mine has a '93 Explorer 4x4 with an automatic. He's getting an intermittent shake at highway speeds. It shows up every 5-10 minutes or so. Apparently the problem has been going on for a few months now. I took it for a test drive the other day, and it feels similar to driving on rumble strips. It shakes in both 2wd and 4wd, but he says it seems worse in 4wd. The vibration feels more like it's coming through the seat than the steering wheel. The vibration will go away if you take the foot off of the accelerator, or if you pull it down into Drive. He's got about 220K miles on it. The previous owner said the transmission was rebuilt about 30K miles ago, but who knows. He's had it in the shop for a couple of days, and they've checked the usual suspects - u-joints, ball joints, and the sort.
View 6 RepliesFord - Ranger :: 1993 Turns Over Without Starting
I have a 93 Ford Ranger I can not get to start. The battery is new, I have replaced the starter and the fuel pump but the truck still turns without starting. I thought maybe the Starter Rely might be the problem but I get spark from it when I do the screwdriver test. I am running out of money replacing all these parts without any success.
View 11 RepliesFord - Ranger :: 1993 - Engine Will Crank But It Will Not Engage
My '93 Ford Ranger died on the road three days ago. The motor simply stopped. Battery is good. the engine will crank but it will not engage. Had it towed to my Shade-tree mechanic he is puzzled. Says that trouble code 5931111111 indicates an air conditioning problem but that doesn't make any sense. The truck is 4 cylinder 2WD.
View 1 RepliesFord Ranger / B-Series :: 1993 - Cat For PA State Emission?
I am starting to work on my 93 ranger when funds are there. But my question is do i need a Cat. for PA state emissions? I have heard you do but then I hear you don't. I have also heard a few things on the fuel millage and power.... Looking for some info on this because I am not trying to cut it off and have to go back and fix it again... I want to do it once and be done with that part!
View 3 RepliesFord Ranger / B-Series :: 1993 - Won't Go Past 35 MPH And Shakes?
Today on my way to work my 1993 ford ranger would shift fine but would refuse to go over 35mph and shook pretty bad. I don't know where to start...
View 6 RepliesFord Ranger / B-Series :: 1993 2.3L 5 Speed Won't Go Into Gear
Not only will it not go into gear, truck will not start unless clutch is to the floor, and in neutral (it's only possible place) if you pick the pedal up 1/4 inch off the floor the odometer starts spinning around 1 mile in 5 seconds.... if you lift it any more it kills the engine like you shut it off with the key.... odometer reads 99,004 miles now (the last 2 are mine) I bought this truck like this ....
View 3 RepliesFord - Ranger :: 1993 - Suddenly Died - Engine Won't Engage?
My '93 Ford Ranger suddenly died while I was driving, no sputtering or bucking, it was just as though I had turned the key off. When i tried to restart, the engine would turn over but not engage. It's as though the engine is either getting no gas and/or spark. My shade-tree mechanic says he got a diagnostic code that was #539 followed by #1 seven times at two second intervals. he says he ran the test 6 times and got the same result every time. What this means?
View 10 RepliesFord Ranger / B-Series :: 1993 / 3.0L V6 - Belt Squeaking Very Loudly
I have a ranger as said in title. No a/c. I noticed my belt was cracked very badly so I bought a new one. Dayco made for Ford and Mazda 3.0L V6. Looked the same length as the old one so I put it on and all was good. Then about 2 days later it started squeaking very loudly, not all the time, just 1500 rpm and higher. The hotter the motor got (not overheating just to running temp) the higher rpm it took for it to squeak. I put a stethoscope on all the pulleys/pumps and alt. It sounded the strongest on the idler.
So I replaced the idler and bearing (which the bearing was bad, but not the source of sound) it wasn't that. So I thought I'd give the belt a couple days, maybe it was too tight causing a bearing to get too tight and squeak. And the more I drove it the louder it got with less rpm needed to make it squeak. So I tried belt dressing, and still no fix. So today I put the old belt back on to see if that was the issue. Sure enough, it started up and squeaked just the same, but I tried the belt dressing on the old belt and it went silent, even at 3000 rpm. So I assume from this the new belt was a smidge too big. Right?
Ford Ranger / B-Series :: 1993 - Wiper Motor Removal?
How do you remove this clip holding the wiper linkage to the back of the motor? I can't see what kind of clip it is to know how to remove it. Ford says to remove the wiper pivot and let it drop. Is that necessary? I can't barely get to the back of the motor so I'm having to feel the clip and remove it but since I don't even know what kind of clip it is it makes it so much harder. Does the cowl cover not come off or is it just this access panel?
View 3 RepliesFord Ranger / B-Series :: 1993 - Front Sway Bar End Links?
I'm new to the whole Ranger truck thing since buying a 1993 Ranger 4x4 for my 14 y/o son. It has a 4 inch suspension lift and a 3 inch body lift running 33x10.5x15 tires. The front sway bar is not hooked up. I know that i will need drop brackets for the sway bar but my question is about the end links needed for this truck. There are 2 tabs with provisions for a horizontal bolt on each side of the twin I-beam where the end link would attach and the sway bar has a single horizontal hole on each end. Searching for replacement links at various auto parts websites only seems to yield the standard end links that consist of a straight bolt with a nut on each end and the rubber insulators. That clearly is not the correct end link for my application. Not sure if the front suspension is the factory installed unit or if it was swapped some time in the part.
View 4 RepliesFord Ranger / B-Series :: 1993 - How To Replace Key Lock Cylinder
I am trying to replace the key lock cylinder (where you insert your key to start the truck) in my 93 Ranger. Using the Haynes manual, I have removed the steering wheel cover (I don't have airbags), pulled the steering wheel, removed the 3 plastic decorative shrouds and looked at a naked steering column assembly. The manual says there is a 1/8" hole on the bottom of the steering assembly where you can push up the actuator pin to release the lock cylinder assembly.
I looked and looked (even with a flashlight) and could not find a hole. I looked at the new key lock cylinder assembly and found the little actuator pin so I sorta know where the pin would be in the installed assembly. The entire key lock assembly is enshrouded (is that a word?) in the cast aluminum steering assembly.
There was a small metal plate - but that plate is just for access of the release of the steering wheel lock actuator (so I carefully bent it back!!). I know all this is for theft protection, but the truck is co safe I can't even replace the lock assembly.
Ford Ranger / B-Series :: 1993 - Modulator Valve Location?
Where the modulater valve is on my A4LD tranny. I have a 93' ranger XLT extra cab 2wd with 4.0 engine. I have looked all over the tranny and thought it would be somewhere I could see it. I know I had one on my old full size Ford truck with C6.
View 7 Replies