Ford Fuel System :: Significant Vacuum Leak Around The Throttle Shaft On The Driver Side
I was using the method of spraying starter fluid around the intake and found a pretty significant vacuum leak around the throttle shaft on the drivers side. The carb is a 2 barrel holley. What are some different ways to seal a throttle shaft vacuum leak? Could I take it apart and seal it with a plastic O-ring for now?
View 2 RepliesFord F-150 (2004-2008) :: Vacuum Leak Causing Erratic Idle - Codes PO171 / 174?
I tugged on the little hose on the back pass. side of the engine,(5.4),...
and I could hear the vacuum leak that is apparently causing the erratic idle, and PO171 & PO174 to come up.
I know this hose is hooked to the Charge motion Control Valve on the back of the manifold,..I can't imagine what it does, as it terminates with some kind of plug or check valve??? Haynes say's to remove the entire manifold to get to the CMCV.
I can see it with a mirror,. I am thinking maybe long needle nose from Harbor freight,...bend the tip short,..maybe be able to change it out?????
Ford F-150 (2004-2008) :: Small Vacuum Leak In 4WD System
Long story short, I have a small vacuum leak in the 4wd system. I disconnected the lines going to the hubs to prevent grinding them to pieces as they are brand new. This, of course lock the front hubs in and disengages the X-fer case in 2wd.
It is not engaging in 4wd unless I select it, so I don't imagine it hurting anything in the X-fer case or anything. Other than the extra rolling mass, is this okay to operate at until I resolve my vacuum issue, provided I close all openings and places for trash to get in?
Ford Fuel System :: Vacuum Control On EFI Regulator
I have an Accel Gen vll EFI setup on a 59AB and plan on using a pressure regulator but it has a vacuum inlet fitting. I'm assuming it's to allow for more pressure on acceleration. When the vacum drops more fuel will be allowed into the fuel rail is my guess.
View 3 RepliesFord Fuel System :: 2150A - No Distributor Vacuum Port
Since the 2150A was computer controlled it has no ported distributor vacuum advance port, correct?
If you have a distributor with vacuum advance and a 2150A carb, where do you connect the advance to if not the carb?
Ford Fuel System :: 2100 Choke Vacuum Control Frozen?
I picked up a renamed 2100 for my '72 and I found out choke vacuum control on the back of the carb is frozen. Are these parts still produced and if not is there another way to make it work?
View 10 RepliesFord Fuel System :: 2100 Choke Vacuum Control On The Back Of Carb Is Frozen
I picked up a remaned 2100 for my '72 and I found out choke vacuum control on the back of the carb is frozen. I can't find anyone who carries it, let alone knows what it is. Are these parts still produced and if not is there another way to make it work?
View 13 RepliesFord - E150 :: Check Engine Light Keeps Coming On - Vacuum Leak / Fuel Pump
I recently had a Jasper rebuilt engine installed in my Ford E150. Since than my check engine light keeps coming on and the computer is saying my cas air mix is "lean". The instaler says i need a new fuel pump.Another mechanic says it is more likely a vacuum problem.I know it's possible that the fuel pump is bad bur since this has just started since the install, I don't believe it can be the fuel pump unless it's just one hell of a coincidence.
View 6 RepliesFord Fuel System :: Leak / Dripping On Top Of Engine At The Fuel Filter
I'm dripping fuel on top of the engine at the fuel filter . Where the line ties into the filter canister, there is a small plate that's attached with small Allen screws its dripping between this plate and the canister .... I assume there is a gasket/oring that is causing it ...... What is the part number or correct description so I can go to ford dealer and get one. It's a 2007 Ford 4x4 6.0 diesel.
View 2 RepliesFord Fuel System :: 1977 F250 - Fuel Leak From Filter Attached To Carburetor
I have a 77 f-250 with a 460 engine and a 4bbl Motorcraft carb and its leaking a substantial amount of fuel out of the newly replaced filter that is attached to the carburetor. The fitting is tight and I even tried buying some small gaskets to seat it, but that didn't work either.
View 1 RepliesGolf V R32 :: Slight Whistling Almost Like Squeaking At Idle - Vacuum Leak / PCV System?
4601 DBP, just under 35k on it. At idle, i hear a slight whistling almost like squeaking. I took it to my independent tech and he showed me that if he removed the dipstick for a second while idling, the noise stopped, due to lack of vaccuum, so he believes its in the pcv system. I am still under powertrain and obviously federal emissions 8yr 80,000. Go start your R and listen at idle inside the car for a whistle or squeaking noise that seems like its inside the passenger dash.
View 13 RepliesFord Fuel System :: Small Leak Where Filler Neck Ties Into Rubber Hose That Runs Into Fuel Tank
I recently purchased a used 1999 F250 Super Duty with about 150k miles on it. The truck runs great and I have no complaints but there are a few things that need to be taken care of. It looks like there is a very small fuel leak where the filler neck ties into the rubber hose that runs into the fuel tank. There is a thin film of diesel along the side of the tank, on the leaf spring, the air bag and various other places. Nothing is dripping. I want to drop the tank and replace the hose. The Haynes manual says to depressurize the whole fuel system--is this really necessary if I don't plan on doing anything to the system aside from dropping the tank?
View 2 RepliesElantra XD (2001-06) :: 2002 GT - Vacuum Leak At Fuel Injector
I have an '02 Elantra GT with ~175,000 miles.
CEL is on, gives code about evaporative emissions control system, P0441. Shop manual says a)Purge control solenoid valve or b) vacuum leak.
Symptoms are very rough idle, strong smell of gas at startup, erratic, racing idle when starting or cruising to a stop in neutral.
Replaced PCSV, didn't WORK. Went looking for vacuum leak. Seems to be at the fuel injector that's on the end, passenger side, on the manifold side. There's a noticeable hiss, and when I spray gumout at the injector it changes idle. Replaced the injector O-rings. Didn't make a difference. What next?
Buick - Century :: Vacuum Leak To Fuel Pressure Regulator
I have a 1992 Buick Century with a 3.3L V6. I noticed a hissing sound under the hood with the motor running. The short vacuum hose (about 2 inches) connected at the fuel pressure regulator was loose and leaking. I shut the engine, remove the end of the hose and a little gas (about a teaspoon) came out of the vacuum pipe for awhile and then it stopped.
I tightened (but did not overtighten) the end of the hose with a nylon wire tie. There was no existing clamp on it. The vacuum leak stopped (no more hissing). Now, the car is sometimes hard to start or restart. Do I have a serious problem? Did I do the right thing? Could this be caused by a clogged fuel filter? (it was changed 42000 miles ago).
Diesel - Brakes - Manual-transmissions - Cylinder - Mercedes-benz :: 1978 - Leak In Vacuum System?
When the brake pedal is first depressed, it sounds like air is being pushed out of it, sort of like flatulence, and are less responsive. When i pump the brake, it fills with air and tightens. The brakes work when I depress the pedal all the way down. Also, I have to pull my driver-side door shut a few times before it will close and lock with the vacuum system. Otherwise it won't close. Eventually the door closes and I can lock it when I shut the door just right. (My mechanic and I are working together to find replacement locks from junk yards) Is this the master cylinder? Or could this be due to a leak in the vacuum system since my door does not readily close? Or is it something else entirely? 1978 Mercedes 240D...
View 4 RepliesFord F-150 (2004-2008) :: 2006 - Excess Crankcase Vacuum Causing Whistling On V8 3 Valve
Can't find the PCV air inlet hose to the crankcase on a 5.4 3 valve V8 2006 F150. Most PCVs let air in on one bank and out the other bank on a V engine, but this engine has hoses going from BOTH banks valve covers to the intake manifold. The crankcase is under vacuum(8 inches vacuum at dipstick tube, 6 inches at each valve cover). There should be air flow in the crankcase not vacuum. No air is getting in which results in a vacuum in the crankcase.
Once the vacuum builds up enough after a few seconds when the engine is started the engine begins to whistle where air is being sucked in(can't figure out where) at a seal or gasket. If air could get in as it should there wouldn't be a vacuum in the crankcase and the engine wouldn't whistle. Where is the air inlet hose for the PCV system on the 5.4 3 valve V8? It must be clogged or blocked resulting in a vacuum. I can't find the hose and Alldata doesn't show it.
Ford Fuel System :: Leak At Accelerating Pump?
I got a 4180 carb and at the accelerating pump I got a leak I wound up putting in the wrong screw so I had to retap the hole put a heli coil for 8 32 screw and now that its tight it has a leak don't have a lot of funds right now so I'm trying to find a solution that is not going to cost to much and forgot the count on pri needles and I got a backfire as of right now and not sure what adjustments need to be made or locations of what to adjust. I need to get back to work and its hard to do without transportation.
View 1 RepliesFord Fuel System :: Rear Tank Leak - No Power
I have the dual tank setup & this is my problem.
Last year I replaced both tanks - the front was leaking bad and rear was starting to leak. After replacing both tanks, the rear tank (which I was using before) was unusable - it would idle fine and when applying throttle would stall out. The front tank's gauge did not work.
This week I pulled both tanks. Had new gauge assembly put on front pump unit. Also had the rear pump replaced with a new (rebuilt?) one. Installed both tonight. Now the front tank is running fine with a gas gauge. I Filled up the rear and once I had about 16 gallons in, fuel started leaking from the front top of the tank it looks like (where in-tank pump is). This leak has continued as the truck was turned off too. I think it may have stopped now, but its dark and I am parked on a hill. As another problem, I still have the same "stalling" problem. The rear will idle fine, but start to stall out when a load has been applied.
So to summarize:
- What is causing it to want to & stall out?
- Why am I leaking gas?
It seems to stop dripping gas after (maybe) the pressure is lower from leaking the gas out. Also, when 1st starting it up on the front tank, it wants to stall out...probably from the gas that leaked out while it was shut off? The truck will run for about 1/20th of a mile on the rear tank when initially starting it up before showing signs of stalling.
GTI 337/20th Anniversary :: Broken Vacuum Hoses Causing Misfires
so i've had my 337 for a couple months now and when i first got it i found 2 broken vacuum hoses that were causing misfires. once i got those replaced my CEL went off and seemed to be running fine other than from time to time when i started it up my idle would be around 1.2k rpms and then after a couple miles itd settle down to 750-800 rpms but it wasn't rock solid, so obviously there is still something wrong.
on my drive home tonight from work i was in the mood for some spirited driving but when i'd hit the gas i could feel some hesitation through the powerband at wide open throttle. when i got home i turned it off, and started it back up to see if it was idling funny and when it ignited the rpms jumped to almost 2k and immediately fell back down to 1.2k.
My thoughts are its either a vacuum leak again, bad/dirty maf, dirty throttle body, or a boost leak.