Ford Fuel System :: 1993 F150 - Fuel Canister Purge Solenoid
1993 F150 302. What does the fuel canister purge solenoid/vac play in the furl/emissions arena?
View 5 RepliesFord Fuel System :: Reconnecting Fuel Vapor Canister Lines
I am done with this swap (I hope) changed out the 302 in my 81 van for a 351. The only smog spaghetti I am keeping is the fuel vapor canister but I am unsure what the #1 line in the photo is for I have the manual but doesn't state what it does my research suggests its a fuel vapor return line from the carb bowl back to the canister ...... I now have an edlebrock carb obviously w/o this port so my question is
#1 where would you reconnect this "whatever it is" line on carb or manifold
#2 I am going to install that #3 fitting in photo on the edlebrock manifold at the same location & extend #2 hose to it. I am thinking that's ok...
Ford Fuel System :: E350 - Fuel Tank / Pump Noise After Cutoff
This van has had a couple of fuel pumps, no surprise there, and i need to look through my paperwork and find out how many miles the current one has on it, but it has the STRANGEST habit I've ever had on any vehicle. Starts fine, runs fine, no fuel pump noise when van is running, and when you turn it off, the fuel pump creeks on and off for several minutes.
I mean a strange creaking noise almost like a shorted electrical device or a vehicle's brakes when you park it on a hill and the breaks creak as it settles into place. I'm probably doing a lousy job of describing this but i don't know how else to describe it!
ALSO, if you lay under the van and wait til it stops creaking, you can tap the bottom of the tank and it will creak for a few more seconds. You can tap repeatedly and make it creak more. Is it about to explode? Can i trust it on a road trip?
Ford Fuel System :: 1988 F150 - No Signal Going To Injector - No Power To Fuel?
cant figur this out have no signal to injectors and no power at fuel pump 88 f150 5-0
View 2 RepliesFord Fuel System :: 1988 - Fuel Pressure Drops Off Fairly Fast When Turned Off
Working on a 88 Ranger 2.9L 5-speed ext cab. The fuel pressure drops off fairly fast when turned off and I'm pretty sure that the check valve is bad. My question is, which pump has the check valve? It is a single mid tank set-up and has a pump in the tank and on the frame.
Pressure is fine while running. about 30psi @ idle and 40psi with no vacuum on the regulator. The pressure drops off within a couple of minutes which causes it to have to crank over for a bit to rebuild pressure and start.
It looks like the frame pump is readily available while the in take pump is special order. I just need to know which one has a check valve. I'm thinking the in tank pump, but I hate to waste money for the wrong pump.
Pressure drop rate
30 psi @ shut off
25 psi @ 1:05 min
20PSI @ 2:30 min
15psi @ 4:45 min
still dropping
Ford Fuel System :: 1988 F250 Stalls - Random Fuel Pressure Loss?
I have a 1988 Ford F-250 Lariat, 7.5L 460, four-wheel drive. I have two fuel tanks on it, and I've been having a really annoying, obnoxious problem with it lately. After running it for a while, I noticed that I keep losing fuel pressure, and the truck stalls. When I try to start it, it does nothing but roll over. It just won't start. I've changed the fuel filter, I know both fuel pumps are working (I turn over the key, I can hear front, back, and high pressure pump attached to the left side frame rail kick in.) It's Fuel Injected, not EFI, hence that third pump. The problem happens a lot, and it's random. I could drive for 100 miles, stop to get something to eat, come out, and it won't start.
I thought maybe it was the fuel pressure regulator, but I don't think that's the case because it still runs. I would assume that if the regulator was bad, it wouldn't run at all. I also thought that maybe it was the relay, but according to some mechanics I spoke too, if I can hear the pumps kick in when I turn the key over, then the relay is fine. The only thing I could think of is that it might be the fuel selector switch. Maybe it's going bad, shorting out or something. When I flip the switch though, it switches between fuel tanks, and the gauge reads how much fuel is in it from the sending unit.
There's a schrader-type valve up by the fuel injectors. When I push it in, it barely squirts any fuel out, if at all, so I know the pressure is low. When I push it in on a good day, it sprays out like a water fountain. Just tried starting it again - no good. Pushed on the valve, it spurted out some fuel pretty well, but still won't start. Occasionally tries to, but ultimately won't. I know the spark is good, checked the plugs/distributor cap. Can't get the sucker to start.
Ford Fuel System :: 4180c - Fuel Coming Out Of Primary Vent Tube
I have a F-250 4WD with 7.5L which has a MC/Holley 4180c sitting on top. It was getting very poor mpg (like 5-6 miles/gal) and then was getting harder and harder to start. This progressed rather quickly to not starting with fuel coming out of the primary vent tube. I suspect it has to do with the primary float stuck open. I was considering rebuilding the carburetor. Is this over reaction prematurely or is there something like float adjustment that may rectify all of the symptoms described. If a rebuild is in order what is the information I would need to ensure getting the correct rebuild kit. Info that I have so far from research is it is Motorcraft ID #E5HE-9510-MC.
View 6 RepliesFord Fuel System :: 1986 F150 - Fuel Coming Out Of Front Tank Filler Neck
I have a 1986 F150 6 cyl, dual tanks, no AC, manual fuel pump. Just recently, I have been having issues with the tanks. At first it seemed like the back tank was siphoning from the front tank. Now I have fuel coming out of my front tank filler neck. When I open the back tank gas cap, there is enough pressure to spray me with gasoline. I am not familiar with the fuel delivery system of my truck ...
View 2 RepliesFord Fuel System :: Oil Coming From Side Of Fuel Pump?
I was letting my truck idle to work on a cooling issue when I noticed oil coming from my fuel pump! What would cause this? It wasn't coming from were the pump bolts to the timing cover it was coming out of the side of the pump it looked like? I'm going to get a new one.
View 7 RepliesFord Fuel System :: No Fuel Coming From Pump Nozzle?
Working on my cousin's 84 F150 351w HO with a Holley 4180 4bbl and auto trans.
I rebuilt the carb because of sticking floats (that and it was filthy and sitting). It fired up and I drove it to my uncle's shop a ways down the road before even adjusting anything. At the shop, it fires right up, idles great and floats and idle mixture screws are now adjusted.
It has a dead spot right off of idle that's been driving me crazy, and stalls in gear if I'm not careful with the pedal.
After reading around here, I looked down the carb to make sure the fuel was squirting as soon as the throttle moved, and noticed there was NO FUEL squirting from the nozzles. So that explains the dead spot...
There was just the needle, then the nozzles, then the screw that went in, same as they came out (only cleaner). Wondering where to go from here to get these working again. Going to pull the nozzles off and see if there's anything obvious going on in there.
Ford Fuel System :: 1988 F150 - Cuts Out Under Load?
My 88 F150 (300 six, 5 speed, dual tanks, 176,000 miles). The truck has the low pressure fuel pumps in the tanks and the high pressure pump on the frame rail setup. Truck starts fine, but cuts out severely under acceleration for the first 30 seconds of driving. After that I only notice the problem when applying a lot of throttle (does not cut out under gradual acceleration) or climbing steeper hills. If I kill it for a few minutes and then take off again the problem is back for the first 30 seconds or so. I have replaced all the tune-up type stuff (all filters, plugs & wires, dist. cap & rotor, ignition coil, o2 sensor, cleaned throttle body, replaced IAC valve, numerous sensors). Timing is dead on at 10 deg. BTDC with SPOUT unplugged. My FPR was bad so I also replaced that. Condition exists regardless of which fuel tank I am using (no problems with tank selector).
Getting no KOEO codes, but getting KOER code 41 and plugs do seem to show a lean condition possibly. I'm still averaging around 16 MPG since this became a real problem about 3 months ago.
I removed the bowl from the reservoir between the tanks and the high pressure pump on the frame. No filter in there, but it was clean with no gunk or sediment found. I removed the line from the inlet side of the high pressure pump and found that while cranking the engine I have fuel flowing freely (same amount of flow regardless of which tank I've switched to). The flow was steady, but not extremely strong. If I understand right the in-tank pumps are not designed to provide much pressure? Below is what I found at the schrader valve:
key on, engine off - high pressure pumps runs for about 1 second, brings gauge up to 48 psi
idle, FPR connected - 40 psi
idle FPR disconnected - 52 psi
revving throttle with FPR connected - 46 psi maximum
Connector, where fuel pump relay plugs in, seems to be clean and not corroded at all.
Ford Fuel System :: 1988 F250 - Injectors Not Engaging
I have a 1988 f-250 with a 460 motor. I have fuel and I have fire. And the truck starts with I prime it. I tried looking for the crank sensor but can't find it. I looked behind the balancer and I didn't feel any wires or anything. I checked on the sides of the motor nothing. It has a new coil pack and ignition mod. Fuel pump and starter. What else can it be?
View 4 RepliesFord Fuel System :: 1988 F250 / EFI - Slow Return To Idle?
Its an 88 F-250 4x4 with a 302 EFI 5-speed. Fair compression, runs smooth. When I press the gas pedal it takes about 5 seconds for the old girl to return to idle. I know nothing about EFI. My buddy,s out of town with the hand held mechanic. Is there anything I could check till he gets back.
View 6 RepliesFord Fuel System :: 1988 - With Both Tanks Full Front Tank Overflow?
I have a '88 F250 with a couple of dual tank issues, first of all if I'm running on the rear tank the fuel returns in the front tank.... not an isssue if trhe front tank is empty, but if both tanks are full the front tank will overflow. If the front tank is empty I run on the back tank until I'm out of gas and switch to the front and I"ll have about a half a tank in the front tank.
Second issue, running the front tank the fuel gauge stays on full until I have about half a tank, then it works OK. If I'm running the back tank it stays on full, even after the tank runs out of gas??
Ford Fuel System :: 1988 - Got Code 41 - Lean Miss At Idle - ECM Or Injectors?
1988 F250 351 5.8
I've worked for months on this truck and I now have it in the shop. The truck shows a 41 code and has a lean miss at idle that get worse during acceleration and cruise. The injectors were refurbished 6 months ago and the ECM was replaced 3 months ago. All sensors are new and within specs. Fuel pressure is good and there are no vacuum leaks.
The mechanic has verified that the condition is not electrical related. The O2 sensor will react if carb cleaner is sprayed into the throttle but other wise shows constantly lean. He's now checking all pins at the computer for any off condition. He is suspicious of the refurbished injectors. I'm wondering if the computer somehow went out again. Which way to go or what/how next to test?
Ford Fuel System :: Location Of Check Valve That Maintains Fuel Pressure On The System?
I have a '99 E-350 6.8L. Where is the check valve that maintains fuel pressure on the system?
I have been experiencing a starting issue when the engine is hot. Cold starts are usually fine. I've replaced the in-tank fuel pump (pump only, not the assembly) to no avail. I was out of town and didn't have access to a fuel pressure gauge when the problem started so I couldn't say what I had prior to replacing the pump. But now, with a new pump, when I check pressure, I get about 40 psi when I first cycle the key on, but it drops right back to zero as soon as the pump shuts off. If I cycle the key on a few times, sometimes I can get it to hold pressure at about 32 psi, and it starts fine. When I shut if off, it goes back to zero psi, sometimes gradually, like a bleed down, and sometimes immediately.
My conclusion from this was that the check valve was bad. I was told it was part of the in tank fuel pump assembly. Since I didn't replace the entire assembly, this made sense. So I just dropped the tank back down, but I don't see anything as part of the pump assembly that serves as a check valve. There is a rubber nipple on the end of the return line, but I don't see how that can hold any significant pressure.
So, before I go out and spend another couple hundred bucks on the complete fuel pump assembly, which apparently can't be purchased without the actual pump, I thought I'd ask. Where is the check valve that holds the pressure in the fuel system?
BTW, I also have replaced the fuel rail pressure regulator, but it made no difference (I went there first since that was much easier than dropping the fuel tank a second time).
Escort :: 1988 EXP Rough Idle - Fuel Coming From Injector
I have an '88 EXP Escort with the non-HO 1.9L
I was noticing a rough idle (vibrating, sounded like it was bogging down)
I changed the plugs, wires, cap and rotor. Still happening.
Noticed that my o2 sensor was unplugged. Plugged it back in. Still happening.
Went to check the air filter and noticed the insane amount of fuel that was coming from my injector.
I am getting horrible gas mileage (8-12mpg)
Here is a video of what I am seeing: [URL] ....
What would be causing that much fuel to be sent out?
Ford Fuel System :: Stumble And Die After A Short Highway Run At 70 MPH / Fuel Injection Flooding Out?
What would make a FI engine act like its flooding out and dying after a short run on the freeway?
Details:
1994 F-350 351W (just overhauled this winter)
has new TPS, ICM(?).
Dual exhaust dumps right before the tires
new filters in tanks, new fuel filter on frame rail
All fuel lines have been opened and blown out from the tank to the engine compartment fitting near firewall.
Fuel pumps hold good pressure when tested.
Symptoms:
smells like its running rich most all the time
after a short hiway run @ 70MPH it will stumble and die when returning to surface streets.
fuel smell near engine sometimes, but no obvious puddles or leaks anywhere.
May be related?:
When on a longer highway run, I can't use the FWD tank for a long period without the engine stumbling and cutting out or popping at times. But I can swap to the rear tank for a bit then run the FWD tank again for a while. driving up hills it seems to be worse, but I'm in the panhandle of TX right now..good grief!
I am having to drive this truck for work long distances. While I dont expect a vast fuel range, it would be nice if I could go a couple hundred miles on 20 gallons of gas....
Ford Fuel System :: 1991 F250 XLT - Fuel Pump Will Not Stop Running
I just bought another 1991 Ford. This one is a 1/2 ton XLT Lariet with the 302 and for the first time I own a short bed. I also have a 1991 F-250 XLT with a 460 and a 8' bed.
Here is the problem, ( I think) it will not run or at least not for long. The fuel pump, which I am guessing is in the rear tank will not stop running. On the F-250 the pump stops running after a few seconds after I turn on the key.
Where should I start to find out my problem with the fuel system?