Ford Fuel System :: 390 Keeps Flooding?
I have a 4bbl intake on my 390, and an edelbrock 750/w manual choke on it. #1407. I can drive this truck just fine for the most part, it has good power while using the primary two barrels. (I think the ones always in use are the primaries?) Anyways if i open all four up, pedal to the floor, but at about 45+ mph, the engine runs no problem, although it seems to drop rpm slightly once the 2nd two barrels are opened.
BUT, if I am shifting, like today example 2nd to 3rd, and floor it from the shift, it popped and died out, flooded. Happened to me twice today within an hour. the first time it flooded I'm not sure why it happened, but the second time was as stated above. Is the carb just too much and floods when floored like that? Anything I can do to eliminate this? accelerator pump setting? If I have too i'll end up buying a 600 eventually, but stick with the 750 for now...
Ford Fuel System :: 1986 F150 - Engine Running Rich / Flooding?
My engine is running rich, flooding? My truck is a 1986 F-150 302 EFI. The engine idles rough, black smoke and soot comes out the exhaust pipes, and black soot on spark plugs. Symptoms seem to disappear if I throttle the engine and hold it, but as soon as I release the throttle the symptoms reappear and in most case causes the engine to die. These symptoms have just started a week ago. What the problem is.
Fuel injectors are cleaned and rebuilt. New plugs and wires. All new fuel pumps and filters. New air filters. New fuel pressure regulator. New dual function reservoir. New 3-piece timing set. New O2 sensor. New EGR Valve and sensor. New idle air control valve. New distributor, cap, and rotor. New ignition coil. New high volume oil pump. New alternator. New pcv valve. New knock sensor and air charge temp. sensor.
Ford Fuel System :: Mild Stumble / Hesitation When Dropped In Drive
460, stock RV motor with LT headers, Alum Stealth intake. Carb is brand new, Holley 600 cfm, out of the box.
Elec choke, vac 2nds. Timing is set to 12 BTDC.
Truck idles beautifully. Drop it in drive, it will ever so slightly stumble/hesitate then go liked a raped ape. Has great acceleration (for a 8k dually crewcab). In my mind, I'm thinking a slightly larger than stock accel pump to give a bigger shot.
However, it does have a 1" carb spacer. That and the hi rise stealth, is it leaning out for a sec and causing the stumble? Would pulling that 1" spacer work? I was thinking the higher the carb the better to get less heat dissipation from the engine's heat. Replacing the heater core now. So I have some time to sort it out. I'd like to road test a tank of gas through it, but gotta fix the heater 1st.
Ford Fuel System :: Hiccup And Stumble When Get On It Real Hard From A Standing Start
My 302 runs pretty good when all warmed up. It has some cold start issues every now and then, but is easily dealt with. My question is how to best "tune" the carb. It's a 600 cfm 4150/60 style Holley single pump, vac secondaries and electric choke. About as basic as you can get. I think I have the fuel level set correctly. I also think I have the "idle mixture" set right. I used a vacuum gauge and moved back and forth between screws till I got the highest vacuum. Is there a better way than that? I have the idle set correctly. the fast idle is a little high, but I can fix that.
Now, my real question is how to fix the hiccup and stumble I get many times when I step into it pretty good. I assume that this is the point the carb is going from idle circuit to main circuit. It stumbles when I get on it real hard from a standing start. I can roll slowly and step into it and it stumbles as well. I also like to blip the throttle when I down shift (it has a manual tranny by the way), and many times I'll blip it and get nothing. Now, it runs fine after the stumble all through the rpm range. That's the only time it stumbles. so, do I need more accel. pump shot?? To compensate on the transfer of circuits.
I also notice when I on it real hard, during the shift right when I jump on it, under the heaviest load, I hear a bit of spark knock. It's not running hot, and the timing is good. Do I need a bit bigger jets? I'm thinking it's going a bit lead during that time, but I don't have any real way to measure it.
Ford - Explorer :: 1997 - No Start / Flooding With Fuel
Ok so I have a 1997 Ford Explorer with the 4.0 SOHC .. The girl that owns it went out and started it to warm up and went back in the house , when she came back out it had died and wouldn't start .. I hauled to our shop and started diagnosing it .
It has spark
has fuel
Timing is good
Fuel pressure regulator is good
Crank sensor is good
About 62 PSI fuel pressure
No CEL
Seems to be getting WAY too much fuel and fouling plugs !
Replaced ECM ...same thing .
Used NOID light on injector wire and I have never seen one get so bright !
Ford Fuel System :: Location Of Check Valve That Maintains Fuel Pressure On The System?
I have a '99 E-350 6.8L. Where is the check valve that maintains fuel pressure on the system?
I have been experiencing a starting issue when the engine is hot. Cold starts are usually fine. I've replaced the in-tank fuel pump (pump only, not the assembly) to no avail. I was out of town and didn't have access to a fuel pressure gauge when the problem started so I couldn't say what I had prior to replacing the pump. But now, with a new pump, when I check pressure, I get about 40 psi when I first cycle the key on, but it drops right back to zero as soon as the pump shuts off. If I cycle the key on a few times, sometimes I can get it to hold pressure at about 32 psi, and it starts fine. When I shut if off, it goes back to zero psi, sometimes gradually, like a bleed down, and sometimes immediately.
My conclusion from this was that the check valve was bad. I was told it was part of the in tank fuel pump assembly. Since I didn't replace the entire assembly, this made sense. So I just dropped the tank back down, but I don't see anything as part of the pump assembly that serves as a check valve. There is a rubber nipple on the end of the return line, but I don't see how that can hold any significant pressure.
So, before I go out and spend another couple hundred bucks on the complete fuel pump assembly, which apparently can't be purchased without the actual pump, I thought I'd ask. Where is the check valve that holds the pressure in the fuel system?
BTW, I also have replaced the fuel rail pressure regulator, but it made no difference (I went there first since that was much easier than dropping the fuel tank a second time).
Ford Ranger / B-Series :: 2000 - Fuel Injection Pressure Damper Location?
I have a 2000 Ranger with the 3.0 in it. Trying to find where the fuel injection pressure damper is located. I was told it's on the fuel rail. Just making sure I'm looking at the right thing.
View 3 RepliesFord Fuel System :: E350 - Fuel Tank / Pump Noise After Cutoff
This van has had a couple of fuel pumps, no surprise there, and i need to look through my paperwork and find out how many miles the current one has on it, but it has the STRANGEST habit I've ever had on any vehicle. Starts fine, runs fine, no fuel pump noise when van is running, and when you turn it off, the fuel pump creeks on and off for several minutes.
I mean a strange creaking noise almost like a shorted electrical device or a vehicle's brakes when you park it on a hill and the breaks creak as it settles into place. I'm probably doing a lousy job of describing this but i don't know how else to describe it!
ALSO, if you lay under the van and wait til it stops creaking, you can tap the bottom of the tank and it will creak for a few more seconds. You can tap repeatedly and make it creak more. Is it about to explode? Can i trust it on a road trip?
Ford Fuel System :: 4180c - Fuel Coming Out Of Primary Vent Tube
I have a F-250 4WD with 7.5L which has a MC/Holley 4180c sitting on top. It was getting very poor mpg (like 5-6 miles/gal) and then was getting harder and harder to start. This progressed rather quickly to not starting with fuel coming out of the primary vent tube. I suspect it has to do with the primary float stuck open. I was considering rebuilding the carburetor. Is this over reaction prematurely or is there something like float adjustment that may rectify all of the symptoms described. If a rebuild is in order what is the information I would need to ensure getting the correct rebuild kit. Info that I have so far from research is it is Motorcraft ID #E5HE-9510-MC.
View 6 RepliesFord Fuel System :: 1991 F250 XLT - Fuel Pump Will Not Stop Running
I just bought another 1991 Ford. This one is a 1/2 ton XLT Lariet with the 302 and for the first time I own a short bed. I also have a 1991 F-250 XLT with a 460 and a 8' bed.
Here is the problem, ( I think) it will not run or at least not for long. The fuel pump, which I am guessing is in the rear tank will not stop running. On the F-250 the pump stops running after a few seconds after I turn on the key.
Where should I start to find out my problem with the fuel system?
Ford Fuel System :: 1995 - Stalls - Now Stop Moving - Fuel Filter?
I have a 95 F150 4x4 reg cab long box with a 302 V8 and dual tanks... I was driving around yesterday when my truck started to lung and then the motor stalled... when I stopped moving I tried starting the truck and it started with no problem, so as i kept on my way, about 5 minutes later the same thing happened and it stalled again, (I have an automatic by the way). but this time before it stopped moving i pump the gas a few times and it fired back up and then stalled again... i switched from my front take to by back maybe thinking it could me my fuel pump in the tank but it did the same thing again about same time later... Would it be my fuel filter on the frame (like in line fuel filter) or why is it doing that? its EFI by the way.
View 14 RepliesFord Fuel System :: 1976 F150 - Fuel Draining All The Way Back To Tank
My vehicle:
1976 F150 2wd Extended cab
390 4bbl
c6 transmission
4BBL Edlebrock Carb
Dual fuel tanks, only rear main tank connected
My problem: For the first year I owned the truck, everything ran fine and it started up really quickly even after it sat for a few days or a few weeks. I have since, for about the last year or so, had to crank it for 30-45 seconds to get it to start. This all started around the time my fuel pump went out. I replaced it with an Airtex fuel pump from Autozone. I also installed a glass in line filter before the carb in front of the distributor.
I noticed that after about 4-6 hours, the fuel had drained out of the filter and that's when I would have to crank it forever to get it going. It also seems like there is no fuel in the carb as it doesn't even try to start when it first gets cranked. I thought this was a bad pump, so I bought a new one last week and tried it again. Sure enough after about 4-6 hours, everything is empty again and it takes forever to start it. So it's not a bad pump, or so I think.
The other day I backed it into my driveway and left it, something I never do. I checked about 4 days later and there was still fuel in the filter. This makes me think that gravity is making it drain back to the tank.
Is there something that would cause this? Also I have found a one way fuel check valve online that is supposed to remedy this type of problem. Do they work for this situation? Or is there something else I should be doing to fix this? It has taken a bit of a toll on my starting system having to crank so long all the time. I have so far had to replace my starter, starter solenoid, and all the battery cables, starter cable, terminals, etc. due to excessive wear.
The valve I found is here : [URL] .....
Ford Fuel System :: Changed Fuel Filter Now Just Cranks But Won't Fire / Start
2002 E-250 with the 4.6 V-6. Pulled the 30 amp fuse, replaced the fuel filter, replaced the fuse, now the truck wont start. Checked the fuse and the kill switch under the passenger kick cover, all ok. Cranks and cranks but wont fire. No problem prior to changing the filter. Even swithed out the relay with another, no luck.
View 4 RepliesFord Fuel System :: 2001 F150 - Truck Will Not Turn Over / No Fuel From Injectors
I've got a 01 f150 yesterday stopped running (like it ran out of gas). Has half a tank. Fuel pressure at rails good but truck will not turn over. Fuel pump and filter less than year old.
View 1 RepliesFord Fuel System :: 1979 F150 - Fuel Pump Leaking From Side?
I've had a fuel leak near the pump of my 79 F150 with a 400 for some time. I didn't know exactly where it was coiming from, but fuel was being sprayed on to the oil filter from something near the pump. I assumed it was the steel line, and that it had rusted through or cracked, and was going to replace it when I had a chance. I was poking around today though, and realized that the fuel was not leaking from the line, but from a hole in the side of the mechanical pump.
For someone who knows what these pumps look like, there is a horizontal cylindrical bump out near the top of the pump, on the side of the pump that is away from the engine. The fuel is spraying in a mist out of one side of that. To me, it always seemed to be a screw channel, but I didn't think the pump was 2 halves put together? Need to know more about my pump, what that bumped out section is, or why/how fuel could be spraying out of it.
Ford Fuel System :: 1990 E250 - Fuel Shutoff Switch Not Activated?
My '90 E250, open road, mini motorhome , says on the radiator mount , that there is a Fuel shutoff switch that may have been activated.... I don't have the manual for it, so I need finding the switch, so I can reset it ....The vehicle sometimes starts after about 2 mins with the ignition on, but today won't start, even after a longer wait. Both tanks are full...Fuel gauge not working , in either front or rear position. I can hear the rear pump,in the tank, but can not hear the front one....When I bought it last year, it ran fine after waiting to start, and both positions worked , no stalling , or shutdown.Came home about 95 miles, and it's been parked almost all the time since. I want to start it up weekly , but am having that same problem ...Today was the first time I could see the Fuel Pump Shutoff warning ...but can 't find the darn switch to try resetting .....
View 1 RepliesFord Fuel System :: 1993 F150 - Fuel Canister Purge Solenoid
1993 F150 302. What does the fuel canister purge solenoid/vac play in the furl/emissions arena?
View 5 RepliesFord Fuel System :: 1990 - Fuel Tank Leaking - Seal Or Replace?
1990 f150
I have a leak in my rear fuel tank, the front tank has been blocked off and is not used, The leak is at the seam of the two part tank, once removed is there a way to seal this? or should I just replace it?
Ford Fuel System :: 1988 F150 - No Signal Going To Injector - No Power To Fuel?
cant figur this out have no signal to injectors and no power at fuel pump 88 f150 5-0
View 2 Replies