Ford 6.0L Power Stroke Diesel :: 2003 F250 Crank But No Start - Popping Noise Out Of The Intake?
My 2003 f250 6.0l just up and quit. It make a popping noise out of the intake when cranking. I am getting 1150 psi at the icp and ipr is at 62% which seems high to me. The FICM voltage seem fine unless the batteries are drained and I am getting FICM sync. I replaced the HPOP, ICP sensor and IPR about a year ago. I recently replaced the air conditioning compressor and power steering pump. I am at a bit of a loss. I did pull the IPR and everything looked fine.
View 14 RepliesFord F-150 (2004-2008) :: 2005 - Whistle Noise Through Intake When Cold
Whistle thru intake. I have a f150 2005 with a 5.4 and it likes to whistle when cold weather when I press the gas it goes away until it idles down?
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Intake Thumping Noise That Varies Speed With Idle
I have recently bought a 04 f250 6.0, and it has the intake thumping noise that varies speed with idle... I was told it could be a broken rocker, a bent push rod, or a broken roller... I am not that much experienced with diesels. I've spoken to the dealership, and they don't wanna fix it, they said it wouldnt hurt it to drive it like that, but the noise bothers the hell out of me, and everyone notices it. so i wanna get it fixed. I am hoping its just a rocker. if it is just a rocker how deep am i in? truck has 240xxx miles on it, and runs perfect other than that noise.
View 7 RepliesTouareg :: Noise Caused By Flap In The Intake Plenum - 2004 V6
I just recently had a noise issue fixed in my 2004 V6 which I thought sounded somewhat like the valve problem you described. The noise was predominantly a low RPMs (1500-1800) when under load (ie uphill, not in park).
It turned out to be a flap in the intake plenum which apparently can become loose on the rod it's attached to and cause a vibration. The parts they used were a ROD and a REPAIR KIT.
Ford Super Duty (1999-2016) :: F250 - Hole At The Back Of Upper Intake Manifold
1999 F-250 LD 5.4... There is a hole on the back of the upper intake manifold, just below the back of the throttle body, is a vacuum hose supposed to be attached here? Have a serious vacuum leak, no coolant loss, no overheating, just had cop's and spark plugs done, now she backfires, stalls and will not stay running, mech. says its an intake gasket but the gasket and lower intake manifold look new.
View 7 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Replace The Intake Manifold Gasket?
I needed to replace the intake manifold gasket on my 2002 f250 v10. Tore everything apart put the new gasket in which was the same as the old one lyrics to notice something isn't right. I have been driving the truck for over 10 years like this. Is it OK to just continue bolting everything down and go on like this? I am guessing the prior owner 10 plus years ago put the wrong intake on. I keep looking up intakes but they all look just like the one I have. Also that port exposed is on the back passenger side.
View 3 RepliesFord F-150 - 1997-2003 :: Ticking Noise In Intake Manifold
Replaced head gaskets on 2003 f-150 5.4. Now I can hear a ticking noise in middle of intake by #5 port. Maybe timing is off 1 link?
View 4 RepliesFord F-150 (2004-2008) :: Intake Manifold Replacement?
Looking for any pictures or directions on replacing the intake manifold on the 2004 F150, 5.4. Got all the parts with the pulgs, and ignition coils.
View 6 RepliesFord 6.7L Power Stroke Diesel :: 2004 F250 - Grinding Noise From Front End
Ok here goes. I recently replaced the front wheel hub and upper and lower ball joints on the the driver side of my 2004 f250 CC SB 6.0 fx4. Now when I put into 4 wheel drive I get a grinding noise that sounds like a worn out break pad from that side only. It didn't do it before and it only happens in 4x4. I have replaced the wheel hubs before and it was fine. Also The needle bearing race on the axle is good.
View 2 RepliesFord - Explorer :: 2002 - Missing At 90k Miles - Noise From Intake Area?
The other day my 2002 Sport Trac with 4.0 started to miss badly. It has only about 90,000 miles on it. It started to do this suddenly from one turn of the key to the next. It also makes a weird noice that sounds as if its coming from the intake area that can be described as a "chuffing" sound thats in time with the engine. The intake also gets very warm to the touch. We have since stopped driving it. I sprayed carb cleaner all around where the intake meets the head with no change in rpm. I also checked the plastic hose that goes behind the engine to the pcv valve and its ok.
View 10 RepliesFord F-150 (2004-2008) :: Small Holes In Bottom 5.4 OEM Intake?
I'm adding an aftermarket intake to my 04' 5.4 & noticed on the bottom of my intake there was maybe 10 small drilled holes, ((1/8") in diameter. Are these holes OEM from the factory, & what is there purpose? Seems to me that the holes would suck in "some" hot air from the engine bay, yet it's main sourse of air is from the inside of the driver's side inner fender well.
View 6 RepliesFord F-150 (2004-2008) :: Possible To Swap Air Intake On 2006 Model?
I currently have a S&B Intake on my 2006 f150, 5.4. I am selling my pickup and getting an 08 with the 5.4 and am in the fortunate situation to be able to have both vehicles with me currently. Question, would i be able to swap the intakes? Place the stock intake form the 08 on the 06 and the S&B fit the 08? I know the pickups are nearly identical, but just want a little clarification.
View 2 RepliesFord Super Duty (1999-2016) :: 2004 F250 4x4 - Strange Noise From Front End
In the last few hundred miles of driving, I notice there is a strange noise coming from what appears to be the front end of my truck. It sounds similar to a buzzsaw or a power sanding tool whenever it comes in contact with an object. The noise starts at around 30 mph, stops from 55-60mph, and starts again around 65 mph. The truck rides and drives normally and there doesn't seem to be any metal to metal contact noises or clunking and the hubs dont seem to be hot to the touch. I was thinking improperly balanced tires, wheel bearing, or front carrier assembly. What it could be? The noise just suddenly started and I was wondering if I should keep driving it?
View 7 RepliesFord F-150 (2004-2008) :: F250 VVT Making Noise When Warm - Both Cam Position Sensor Codes
2008 Ford F-250 5.4L VVT. Setting both cam position sensor codes and both VVT PO12 and PO22 Codes. Runs good for a few minutes cold then goes to making noise and retards timing when warms up . Replaced both cam phasers and 1 vct solenoid and camshaft position sensors, changed oil and filter with motorcraft.. Tried unplugging VCT solenoids but still runs bad when warms up. Ran bad when engine was cold or hot before replaced phasers now only when warms up. Is it a oil pressure problem pressure shows good on dash gauge.
View 8 RepliesFord F-150 - 1997-2003 :: 2001 - Cold Air Intake Making Humming Noise?
I just installed a cold air intake on my 01 f150 with a 5.4 and as soon as i started it after the install there is a loud humming coming from the intake but with some throttle it goes away. ive looked around on some of the other threads that suggest the iac valve usually causes this humming noise but why would it go bad with the install?? also i broke iac breather trying to remove it from the old hose to install with the new hose so i just connected the new hose directly to the inlet behind the intake until i can get another one to replace it. could this be causing the humming as well??
View 14 RepliesFord F-150 (2004-2008) :: 2006 - Coolant Leak At Intake Manifold
I have a 2006 F150 screw 4.6 auto 116k miles that has evidence of a small coolant leak where the intake manifold joins the head. This is on the drivers side directly under the thermostat housing. The t-stat housing is dry and the hoses all appear dry. It's just wet right at the gasket where the manifold joins the head. Reservoir is still normal so it's not leaking too much just yet.
I searched this site and youtube but didn't find any other posts. Lots of problems with older trucks with composite manifolds but nothing for this one. It looks like a part of the bottom of the manifold is plastic but the entire top and where it is leaking is all aluminum.
It seems odd that this would start in the winter time just driving back and forth to work (no load). And, yes the antifreeze is good. Just wondering if this is a known issue with this truck. Is it just a matter of replacing the gaskets or is there some other flaw I should be concerned about?
Ford F-150 (2004-2008) :: 2005 - Added Cold Air Intake Now Die After Start?
I put in a cold air intake in my 05 5.4l. Now truck will start up then die, the throttle doesnt seem to open up when i step on the gas. everything was working fine before I started on it.
View 4 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Loud Whine Noise Comes From Under The Hood
I have a 2004 Ford F250 Turbo Diesel, egr delete, headstuds, intake, dual stacks, etc and when i turn my wheel a loud whining noise comes from under the hood, I noticed it put tension in my brakes. When I accelerate it gets louder and when i let off the gas it goes away... i checked my fluid in my steering pump and it was low so i put some more in and the next day it was all sitting under neath the truck.... any quick fix or do i need to replace the whole pump?
View 2 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Grinding Noise When Hubs Are Engaged
Okay this is what I got; I recently purchased high mileage 2004 F250 Super Duty short box super cab 5.4 liter. Came with manual 4x4 handle on the floor so no 4 wheel on the fly and this eliminates the vacuum for the auto hubs so this will not be part of the problem. When engaging the hubs and ONLY when engaged the driver side hub grinds. The 4 wheel drive works but it sounds like its ready to grind itself into oblivion. I did pull the hub and the grinding was gone, I happen to have a spare hub that is good and the grinding returned.
I have jacked it up and made sure I have no play in the wheel itself and the axle knuckle on the axle shaft. Some say remove the front drive shaft? Or turn the wheels all the way in one direction engage the hubs and check for binding? I will do this in the morning, but what does that confirm if it not the hub. Could it be the passenger side echoing across? On my 99 Super duty I kept hearing moaning coming from up front like the breaks were shot and if you stuck your head out the window it was the back echoing to make it sound like the front.