Ford F-150 (2009-2014) :: 2013 5.0 - Idling Rough On Start Up?
I've only had my '13 STX with the 5.0 for a little over a month now, but it seems like the past few days, something's caught my attention. As soon as I start my truck when cold, the idling engine seems to have more vibration than normal, which is to say I can notice a distinct vibration in the cab. It only does this for about 10-15 seconds, and then the vibration goes away when it idles down. The truck still runs and drives fine, and I only notice this when I start the truck without it already being warmed up. I don't recall noticing this the first few weeks I owned the truck, but I also wonder if I'm over-analyzing matters as well.
View 5 RepliesFord F-150 (2009-2014) :: 2010 - Rough Idle With AC On
2010 F150 4.6L 2V, 50k miles. Have recently developed an issue with an extremely rough idle with the AC on and trans in Drive. If in park, the idle is high enough that it is much less noticeable. I have cleaned my throttle body, and MAF sensor ? After this , I disconnected battery for about 30mins and let the computer reset. After a long drive today, it is still happening. This engine has the servo controlled throttle body, and therefore no IAC valve that I can identify. I would assume that the idle increase necessary for the AC to be on would come from the servo controlled throttle body itself with no need for an external IAC. The idle in Drive with the AC on will drop to 500 RPM or less and it is very rough. Is there a procedure for a recalibration of the servo throttle body that I could try ?
View 14 RepliesFord F-150 (2009-2014) :: Idle Rough Sometimes Almost Feeling Like It Was Going To Stall Out
I have a 2013 with the 3.7 in it with 24,000 miles on it. I bought the truck used with 8,000 on it was a pre-Owned certified and it already had a k&n air intake which I know it's not needed and I would much rather have the factory intake instead.. 7 months ago I took it to the dealer because I noticed at stop lights it idled rough sometimes almost feeling like it was going to stall out so I took it in and they said that the motor was getting to much air and causing it to run like it was and they said the cooler weather was making it worse and said it should get better when it warms up and they said it wouldn't hurt anything... Well I live in Florida and it's been in the 90s and it still idles like crap you can feel the vibration through the truck...
And it's so aggravating and annoying and I wish I had a stock intake that I could install on the truck to see if it fixes the problem but I don't and I've researched the problem and have seen people with the same issues without the k&n air intake and I've also been told that the stock air intake gives the motor just as much air as the k&n so with that being said did the dealer take the easy way out and blame the intake or should they be responsible for installing the factory intake back on since they made it a certified pre-owned with the k&n on the truck? It's been frustrating because I don't know a whole lot about gas motors.. And I'd like to get the problem fixed while I still have warranty ..
Ford F-150 (2009-2014) :: Rough Idle - 049-.053 Park Plug Gap On 5.0?
My truck has a similar rough idle and I decided to investigate. What my plug gap was supposed to be as I didn't have access to my owners manual at the time. The specs I was given (.041-.047) is what I followed and recapped my plugs .045. The idle improved a great deal.
Now I was wondering and finally got around to checking my owners manual after I read somewhere that the gap for the 5.0 changed between 12 and 13 model years. What I found in my owners manual is that the gap I'm supposed to have is from .049-.053. My plugs were out anyway at .057. I will leave them be at .045 but am wondering why the change from .041-.047 on the 2011 model years to .049-.053 on the 2012+ model years? I assume the engine hasn't changed, so am curious of the thought process.
Ford F-150 (2009-2014) :: 2013 - Slight Miss At Idle
I have a 2013 F150 4x4 with a 6.2 and it has a slight miss at idle. It's done this since new and over the 20kms it has now I've been given the round around on it from 2 different dealers. I'm told there is no code so they can't do anything. I'm thinking maybe a coil? Or perhaps injector?
View 6 RepliesFord F-150 (2009-2014) :: Random Misfires On Cylinder 1 / 3 And 4 - Rough Idle
Ok so I have the 2009 f150 4.6l 2wd. Have random misfire codes. Horrid idle. I replaced all of the spark plugs, coil packs, and even the injectors on 1/3/4. Still codes nothing is better. I'm thinking maybe an intake manifold leak,? I see no real signs but I do hear that little pop pop pop. Now I have a gasket kit for it but I see you can order complete manifold kits with thermostat and gaskets on amazon for like 60 bucks more. The issue is I see none that fit my truck. Is it the same as the mustang? Hate to blow more cash as its adding up.
View 4 RepliesFord F-150 (2009-2014) :: 2013 - Idle Was A Bit Jumpy Warm Or Cold
Got a 13 f150 with the 5.0. I bought it used with about 14 thous kms, now it has 17. Ever since I owned it I noticed the idle was a bit jumpy warm or cold. I didn't really pay any attention to it as it wasnt throwing a CEL or anything but now that I have a roush exhaust and intake I have started to notice it a lot more....not that its worse but at idle my truck sounds like a boat. Weird comparison I know. It seems like it'll jump within +/- 200 rpm @ idle which IIRC is 1K rpm.
View 7 RepliesFord F-150 (2009-2014) :: 2012 - Rough Idle Upon Start Up - Injector Is Cutting In And Out Or Missing
2012 F-150 5.0 Rough Idle Upon Start up - YouTube
Whenever I first start my 2012 F-150 with the 5.0, it idles rough and if I step on the gas it acts like either an injector is cutting in and out or it's missing. It doesn't really seem like a miss though, more like an injector/fuel issue. What it could be. If I let it sit and idle it won't go away unless I step on the gas and get it > 2500rpm or so.
Ford F-150 (2009-2014) :: 2011 XLT - Idle Slightly Rough In Drive / Stall At Stop
I have a 2011 XLT 5.0 V8 with 133,260 miles. I have extended warranty for the next 12,000 miles...which is great because I drive about 400 miles a month... Anyhow it runs great but for one small issue (hopefully) that has been intermittent.
She likes to idle slightly rough in drive at a stop or very low speed, and in reverse at slow speed. If I don't maintain the RPM it will stall and the low oil pressure light will come on, which I imagine comes on because of the sudden stall.
I first noticed this while backing into my garage in the driveway, It would fluctuate in RPMs and if I didn't maintain the gas it would shut off. I took it to the dealer and all they were able to tell me was the Tranny fluid was low and it would cause it to shut off at incline because a sensor isn't detecting fluid in the tranny. I thought this was weird but being as I have never owned an F150, I didn't know better.
It was fine for a little over a month and it started doing it again at stop lights and backing into my driveway. It has become frequent but there is no issue driving at speed and on the freeway. There is no stuttering or shaking and if it weren't for the fluctuating RPM at a stop and the stalling, it would be hard to tell if there was an issue.
All I can note is that there is a clicking sound under the hood, if I remember correctly the last time this happened I was at a 1/4 tank of fuel like I am now, I also feel like it may be a throttle body issue, or some sort of air sensor, I plan on taking it to the dealer but I figure I would get a more informed answer on the forums.
I also hear this is a common issue with the 5.0s... I purchased the truck in December and since then I have only put 250 miles on it.
Ford F-150 (2009-2014) :: Ticking Noise At 800 To 1000 RPMs / Rough Idle Leads To Engine Fail
2010 F150 ... So I have the tick noise at rpm's 800-1000 at drive through, stops, etc. So I did research on it a few months ago and saw that it might be VCT's but should be able to drive. so I drove it waiting to save money and have it go to a shop. well this past weekend while coming home from work my oil light came on the pressure dropped to zero, I was on the highway so I drove about another mile to get off highway and once I got off my truck died. I had it towed to my house and I thought I blew my motor. So I started doing research here and found that the VCT's AND cam Phaser could be bad. so I replaced my VCT on driver side put it all back together it started and loud knock was gone. then after 5 mins it was back very loud knock!
So I shut it down and took apart the passenger side once I got the valve cover off I found the problem.... The bolt that holds the cam phaser in place snapped off and was riding along the camshaft. So I took that out and extracted remaining part of bolt. inspected my camshaft and it was really messed up. so I bought new Phaser and Camshaft. the camshaft just came in today and I am trying to put it back in. but the hole for the pin in the phaser doesn't line up and I cant spin the shaft to make it line up. should I spin the cam phaser? I marked the chain and the phaser is where it should be on chain, but with that bolt snapping off could that have thrown the timing off so my mark is no good? when I lay the camshaft in place it sits perfect and if I just move the phase over 2-3 links it will all fit together. Should I do that?
Ford Aerostar :: 1992 - First Crank Rough Idle On Startup
1992, shory 3.0 130K MILES
On start up runs very rough, will stall if not power braked or revd a little on start up/out of the driveway.
VOLT METER STARTS GOING NUTS!!
After a mile/warm up,,, runs great. But sometimes even when its hot, it will still try to do the rough idle briefly after just a few minutes restart. Give it a few revs at that point and its good. And once in a blue moon it will do it randomly at a stop light,, out of the blue. Very rare
Ford Escape / Hybrid :: 2004 - Intermittent Rough / Low Idle / Misfire On Startup
My g/f's 2004 Ford Escape (3.0L V6 AWD 112,000mi) is acting up. After a full day of sitting, with the second half of it raining steadily, she was driving her Escape and it was acting funny (miss-firing, she said). The engine light came on and soon began blinking. She got to my house shortly after it started this. We left it and I drove for the day. Later that night, I drove it and it seemed fine. The engine light was on, but not flashing anymore.
The next day I took it my friend that was a Saturn mechanic and now working at a KIA dealership (same owner as the former Saturn and current Buick/GMC and Chevy Dealer). It ran fine for me. So he tries to scan it, his Mac Tools scanner won't read it. The KIA scanner wouldn't read it. I drove it the Ford dealer up the road. They said they couldn't get to it until after lunch, I just want the codes read. They re-iterated, and I told them to pound salt and went to an independent shop where I know a guy. They read it right away for me. "Mis-fire on start-up" & "Cylinder 4 Mis-fire." were the two codes stored. He cleared them.
She got the tune up basics (plugs, wires, air filter, etc) and did the complete tune-up herself yesterday. (I was impressed). She put 94 in the tank and some fuel system cleaner in it as well. She said there's been no change and today I finally saw what it was doing. Sometimes during idling at a stop light, the RPMs will drop to almost zero, the lights dim but so far it has not stalled. It'll do this for several seconds, then correct itself and idle normally.
Currently, the engine light has not come back on. She's thinking coil pack (each cylinder has a coil on these engines) on #4. She wants to switch it out with #1 and see if the problem follows. I think that might uncover the cause, or it could be the battery. It's the original, never been replaced and has a lot of miles on it, but it survived this past winter, without trouble. In my experience, most batteries crap out due to age in the fall when the cold snaps start.
Ford 6.0L Power Stroke Diesel :: Idle Seemed A Little Rough At Startup - Bogged Under Accelerating
Happened last night two blocks away from home. The idle seemed a little rough at start-up but didn't think much of it because the coolant temp was only 132 degrees. Pulled out of the driveway up to the stop at the corner. Totally bogged upon accelerating, went a block, then came the sound of a hubcap rolling down the street along with a check battery light, no power steering, and REALLY sucky brakes.
View 14 RepliesFord F-150 (2009-2014) :: 2011 - Squelching Belt Upon Startup
I've got a 2011 F-150 FX4 Supercab with the 5.0L.
I've noticed that very seldom when starting it up, something under the hood squelch's very briefly. The trucks got 3019.0 miles on it as I write this letter. The actual noise itself come's and goes in less than 1/2 a second, and the trucks only made this noise 3 times during the 3000 miles I've owned it, and all the times have been fairly far apart.
I was wondering if this would be cause for concern? My old 1990 F-150 use to do this, but its issue was the bearings going out in the alternator. With only 3000 miles on my new truck the bearings should be a non-issue. Everything should be a non-issue for that matter. I'm not actually all that concerned about it, as I said in 3000 miles its only happened about 3 times...So once every thousand miles or so. And as I said the noise comes and goes in less than a second, and truck always runs just fine. Its never driven any differently.
Could this be attributed to all the heat we have been having lately? I live West Texas and right now 105 to 110 degree days are pretty much the norm, and have been for almost 2 months now. Could the excessive heat cause any to screech like that? And of course the truck has not been overheated, nor has it shown any signs of overheating.
Ford F-150 (2009-2014) :: Twin Turbo V6 / Startup Rattle
This engine really puts out the ponys. it tows ok but not like my diesel. The twin turbo does not get the claimed fuel economy. And now the start up rattle. I seem to be getting the run around on the repair.
View 3 RepliesFord F-150 (2009-2014) :: Rattle At Cold Startup Getting Worse?
Still considering the change from my '08 F250 to a newer F150 with the EcoBoost. I have been driving as many of them as I can to get a feel for them. My current question is this: if one exhibits the dreaded rattle at cold startup, does it always get worse with more time/miles? I found another one that I'm pretty happy with overall, but it does have the startup rattle for about a second at cold start, and only at cold start. Is it worth the gamble, or should I keep looking? It's got about 108k miles and is otherwise in fantastic condition...
View 8 RepliesFord Ranger / B-Series :: 1997 - Rough Idle At Startup / When Rev Up Chugs Real Hard Then Dies
I am currently working on a 97 ranger with a 4cyl and 5 speed. its having some idle issues that i cant seem to pin point, you can start it and it will idle rough then when you rev it up it chugs real hard then dies. used my scan tool and all the sensors are good, fuel pressure is good, good compression, all 8 plugs are firing good and no codes. The other deal that has me a little confused is when I unhook the hose that runs from the air intake tube to the valve cover, I get a lot of vacuum at that port on the valve cover that the hose hooks to. Also when I plug it and pull the dipstick, I get vacuum at the dipstick tube. never seen this before but at the same time I've only messed with very few of these trucks so I don't know whats normal.
View 6 RepliesFord F-150 (2009-2014) :: 2010 - Misfire Right After Startup - Almost Stalls Out At Stops
My 2010 F-150 5.4 L has developed a misfire. I don't have the codes right now but can get them. Replaced all plugs and 3 of the 8 cops. Misfires right after startup but as it warms up tends to smooth out. When it is acting up it almost stalls out at stops. Where to next?
View 3 RepliesGolf V R32 :: Rough Idle After Cold Startup
If my car's been sitting - say monday morning after sitting all weekend in the garage- it runs rough for a little while. Sometimes only for a few seconds, sometimes for a little while after the idle drops. The colder the car is, the longer and worse the condition. It feels like a cylinder isn't firing.
After a particularly cold and wet spell (I had the car outside) it ran so badly it threw a code for one of the cam position sensors and #4 misfire. I replaced both of the sensors. That worked a little.
Since I was due for 80k service and saw a misfire when damp, I replaced the ignition coils along with the spark plugs. That worked a little more. But, it still does it. What else could it be if not ignition? Sticky valve? something else?