Ford F-150 (2004-2008) :: Rough Idle / Engine Stall Out While In Park - Lean Code
My 04 F150 has started having a rough idle. While in park the engine will stall out with the A/C off. Also when in drive the truck will idle close to 1000rpm's. I had to the fuel filter cleaned and also the MAF sensor cleaned. Also did a vacuum check on it. Pulled the code and it's throwing a Lean Code. What else should I be looking for?
View 12 RepliesFord F-150 (2004-2008) :: Intermittent Rattle / Knock / Running Rough And Dying At Stops
I am working on a customers 08 F-350 5.4l has 135k on it. came in with a severe rattle/knock, running poorly, and dying at stops. ECM gave up 8 codes relating to the timing... Found the phaser replacement steps here on FTE and followed them and replaced the VCT solenoids since i was in there. Customer reported that he replaced the cam sensors already. Ran great for a day, and the next day when I pulled into the shop it gave me a rattle. Not as violent as before but noticeable. I special ordered the wedge and followed the replacement to a 'T'. I have no performance issues and no codes.
View 5 RepliesFord F-150 (2004-2008) :: Rough Idle When Put It In Park
An injector stuck open on my 05 5.4 and bent a rod. I had a new rod put in and all new revised Motorccraft injectors. This was about a month ago. Truck has ran great for the past 3 weeks until today I put it in park and it idles real rough, put it in gear and it smooth as butter again? (Once in a rare while it will continue to idle rough in gear for a few seconds but then clears up.) New motorcraft plugs were put in right before it bent the rod. The truck runs real strong other wise. I am about done with ford this pickup has been the biggest pile I've ever owned one thing after another and just when I think its fixed its some other stupid problem. I'll start by cleaning the maf and throttle body. Could it be a bad coil?
View 3 RepliesFord F-150 (2004-2008) :: 2005 - Hard Time Moving From Park To Drive And Reverse
I have a 2005 Ford F-150 with a 4.6L and auto tranny non 4 wheel drive. I have a hard time moving from park to drive and reverse. Is there a switch that lets you put it in gear once the brake pedal is depressed? Could that have gone bad?
View 5 RepliesFord F-150 (2004-2008) :: 5.4L Engine Has A Knock
A 2004 and up f150. I found one in great shape for 5,000 dollars with 120,000. Drives good but it has a knock I'n the 5.4 engine. It gets quieter when the engine is warm. Should I avoid this truck or will I be okay with purchasing? Only thing holding me back from buying truck is the knock...
View 9 RepliesFord F-150 (2004-2008) :: Trans Has Delay Engaging When Moving Gear Selector From Park To Either Reverse Or Drive
I have a 2008 F-150. When moving gear selector from park to either reverse or drive, trans has a delay engaging. After engagement, it runs fine, shifts ok, downshifts ok....
View 7 RepliesFord F-150 (2004-2008) :: Idle Really Rough When Put In Reverse After Oil Change
Okay I have a 2006 F-150 5.4 60,000 miles , Never once had any problems. I have always done the oil changes myself using 5w-20 mobile super and an S2 STP oil filter. Today, I did a normal oil change and once i filled it up I checked the oil it one last time and I topped it off just right according to the dipstick. And I also checked it after letting engine idle for 5 minutes. I changed the fuel filter also ( first time doing) but no leaks. I drove about two miles down the road, turned around and when I put it into reverse it idled really rough. It almost sounded like a thrown rod.
The rpm's dropped to about 500. I put it into drive and gave it a little gas and then all was fine. Engine ran perfect. I reversed it at least 5 more times and it did it every time but always recovering when given a little gas. I also noticed that there is some oil splashed on the undercarriage like it was leaking going down the road. I checked the filter gasket and it was fine and intact. It idles great in park, drives great. Just reverse it dives down and vibrates like crazy.? After getting home I noticed that the oil level on the dipstick is a little less than a 1/4 inch over the correct level.
Ford F-150 (2004-2008) :: Engine Noise - Knock Or Tick At 1000 RPM
Knock or tick at 1000 rpm. Truck has 20000 miles on it. Dealer replaced cam phasers. What next?
View 1 RepliesFord F-150 (2004-2008) :: Truck Idles High And Rough In Any Setting From Park To OD / Stopped Or Moving
I am trying to solve a mystery on my mom's truck. It's an '06 4.2L F-150 STX with about 133k miles. It had a check engine light on until today- I cleaned the TB and changed air filter yesterday, and both were filthy. Code vanished later on while driving.
I want to check the PCV because the truck idles high and rough in any setting from park to OD, stopped or moving. Worse when stopped though. Entire coil pack has already been changed due to previous misfire problems. This feels similar to a misfire but without the acceleration hesitation. It has also had a recent oil change, and fuel/oil filter change as well.
There is only one hose connecting to the intake on this truck, and it appears to be a vapor line of some sort to the valve cover, but isn't a PCV cause it's just a hollow tube. There is nothing else coming out of the TB at all, except for the throttle control cable. I don't even seen any nipples or connections or holes where a PCV hose or valve should go. I thought it was on the passenger side, under the TB... but there is nothing here at all. I'm stumped.
I am beginning to think the truck just does not have one at all, which I know for a fact is impossible. I have traced every line on this motor from top to bottom, and I do not see it. Should have a heater on it I assume? What else can make the truck so rough? I don't buy it that "it's just that way". That is complete, lazy, BS. I have had/driven many trucks; 4x4s, supercrew, diesels, jeeps, dump trucks... I have NEVER had a truck run as badly and roughly as this one does. Heck, a twin-turbo 700HP diesel doesn't run this roughly.
Ford F-150 (2004-2008) :: Engine Knock / Clunking Noise When Come To A Stop Or Takeoff Or Steering
I am having a hard time locating a mechanical knock coming from my truck. This is not an engine knock but rather a clunking noise when I come to a slightly abrupt stop and sometimes when I take off or am steering. I have recently replaced my upper and lower ball joints and all the u-joints as well. My truck has a 6" Fabtech Coil over lift and a 3" body lift. The truck is also rather squeaky when going over speed bumps.
View 8 RepliesFord F-150 (2004-2008) :: 2006 - Rough Idling When Warm And Dying At Stops Or In Reverse
My brother's 5.4 has been rough idling and dying at stops and in reverse for a few weeks now. Today it threw a code and he finally had me look at it and it's a P0345 code. I was thinking cam phasers possibly, but I didn't think that would cause a code to throw. Also, all I hear about cam phasers is that it makes the truck sound like a diesel, but his when it's about to die sounds like the engine is about to drop out the bottom of the engine bay. Really rough, REALLY loud knocking, etc... What we should be looking at replacing to get this thing back into shape?
View 3 RepliesFord F-150 (2004-2008) :: 2005 - Rough Idle At Low Speeds Primarily In Reverse / Code P0022
2005 f150 Lariat 4x4 5.4
Had phasers, tensioners, chains, guides, and sensors replaced. After driving the truck, it started to get a rough idle at low speeds, primarily in reverse. Changed both vct solenoids with no results. Started to get p0022 code. Changed the oil with motorcraft filter and 5w-20 twice after the work had been done, thinking it might need it. Vct's were a little varnished, but not too bad.
After a couple days of light driving, got a misfire on #3. Replaced the coil and it hasn't been back since. I am stumped at this point.
The computer show the timing to be at +13 when sitting stopped and in drive. It fluctuates a little, but not much. When the truck goes into a rough idle. The rpm's fluctuate wildly. It seems to be happening more frequently, the more I drive it.
Ford F-150 - 1997-2003 :: Running Rough - Surging In Park / Drive And Reverse
I have a 1997 ford f150 5.4 litre truck and the truck runs real rough kinda surging in park and in drive and reverse i have a couple oxygen sensor codes P 0171, P0174, P0136, P1131, P1151 and an idle air control valve code P1506...
View 5 RepliesFord - Taurus :: 2008 - Slight Shudder / Jerk When Put In Reverse Out Of Park
About three weeks ago I noticed a slight shudder in my 2008 Ford Taurus with app. 75,000 miles (automatic). It did not come from the steering wheel, but the car itself seemed to be shaking, but only slightly. Like someone who's had too much caffeine holding out an unsteady hand kind of shudder. It was going in for an oil change anyway, so I had my mechanic check it out, even thought the shudder was gone the next day. It came back, for a few moments while the mechanic was driving. He couldn't tell what was causing it, but said not to worry.
Two days later when I was in the car for the first time that day the car jerked when I put it in reverse out of park. I checked the transmission fluid, and, sure enough, it was about a quart low. All symptoms went away. I took it back in to double check that there was no leak and that everything seemed in good working order. The car was given the all-clear.
Then this week the shudder returned, again, only sometimes. It doesn't seem related to temperature, distance driven, or weather. And the maddening thing is that it only does it sometimes. I checked the transmission fluid again and it is still in the safe zone.
Two days ago, after being parked overnight, the car shook very noticeably for about ten seconds the first time I switched it out of park, first into reverse, then into drive. This was different to the other shudder (I know, seriously). This was a shake, like the bass in a super strong stereo was cranked. Then it stopped and the car drove just fine. I parked it for twelve hours then switched the gears again. Nothing out of the ordinary happened.
Today it had no issue when I first switched gears, but while I drove (for about a half an hour) that original slight shudder was there. This time at all speeds, not just low ones. I went where I needed to go, drove it again about four hours later and it was fine. No shudder, nothing and this drive went through road work with stop and go traffic as well as some time on a highway at speeds up to 55mph. I drove it another time after that, and again, no symptoms. Finally, I drove to the store. The shudder had returned. I parked, shopped for about 15-20 minutes, returned to the car, and it hesitated to accelerate as I pulled out of the spot. It did not jerk or seem to try to catch up. It simply delayed, but accelerated smoothly.
I parked again and let it rest for about 10 minutes, started it up, and no trouble at all. Even that weird shudder was gone. I think this car is toying with me. I'm taking it back to the mechanic, but the trouble is that it doesn't always have these symptoms. I drove it Thursday on a two hour trip and back again with no issues at all. This might make it difficult for the mechanic to diagnose, but at least it's a guy I trust. There are no warning lights on, no smells (unless they are faint as I don't smell things well), and no strange sounds.
Passat (B5) :: Engine Knock Noise When Engine Fully Warmed Up And In Drive Or Reverse
OK--2001.5 1.8t Tip, 85k, nothing but Mobil1 since day one religiously. At around 81k miles the t/belt tensioner seized & let the belt jump and bend a few valves. Had VW do the repair under the p.t. warranty. Engine now runs very well again except there is a knock noise that sounds an awful lot like a crank or rod bearing. The noise is worse with the engine fully warmed up and in drive or reverse. Took it back to VW, they said it's a bearing in the a/c compressor. Sounded like B.S. to me, since the noise is no different with or without the a/c on. I picked up the car & removed the a/c belt at home & found the noise was exactly the same. I've about had it with VW on this issue. Been back 3 times with the noise complaint, & the noise is getting worse!!
View 1 RepliesFord F-150 (2004-2008) :: 2007 - Engine Flutter And Stalls In Reverse?
I have a problem. My 2007 ford f150 4x4 5.4 triton engine starts to flutter and stalls when its in reverse, engine is warm, and I am backing up a trailer with about 5,000 lbs on it. It drives fine with or without towing. I did notice it does it with nothing behind it on occasion. Whats causing this?
View 2 RepliesFord F-150 (2004-2008) :: 2007 - No Reverse Gear But Engine Is Good?
Much done as well. I bought a powertrain and engine that are from a 2009 their both supercrew can I swap the cab easily are they compatible
View 4 RepliesFord F-150 (2004-2008) :: Rough Idle When Engine Is Warm
I purchased an '08 F150 about 6 months ago, and have a problem that two mechanics haven't been able to solve. The truck has a 5.4L engine. Unfortunately, I bought from an auction and the 30 day warranty expired before I realized the problem.
After a longer drive (30 minutes to work) the engine is warm, and I always back into my parking spot or driveway. In low gear, it begins to idle very rough and the engine shakes. If I leave it long enough, it will stall. Usually I pop it into neutral, give it some gas, and its fine. I just bought a camper trailer, so I'll need to use the lower gear when backing up.
So far, the engine has been flushed twice, the solenoid replaced and phaser replaced. The second mechanic has recommended I contact a dealer, but haven't had luck with them with my previous Explorer. What it could be? I will be getting the diagnostic paperwork this week.
Ford F-150 (2004-2008) :: 4.6L Engine Hesitation And Rough Idle
I have a 2008 Ford F150 4.6L and its been broken down in our shop for quite some time now. It started acting funny when I could not get the truck to do over 80kmh. Slow acceleration, and a horrible shaking when it idled. Eventually it was undriveable since I could go above 50kmh anymore. From looking online we replaced the plugs and coils. We removed the intake to find the gaskets were shot so coolant was leaking into the spark plug tubes which could've been the cause of a misfire. Fixed that. Still the same. We replaced the egr valve and dpfe sensor because we keep getting the P0402 excessive egr flow code. Still no luck. My dad is a journeyman hes just not too familiar with newer trucks.
View 4 Replies