Ford F-150 - 1997-2003 :: 2002 Truck Starts Jerking Once Get Up To About 50 Mph
Transmission problems 2002 f150 lariat... Once I get up to about 50 mph the truck starts jerking around..
View 2 RepliesFord F-150 - 1997-2003 :: Truck Only Starts After Being Jumped - No Gauges
Ran for a month just fine. Now it will only start after being jumped. Everything worked just fine.... What should I test first?
View 8 RepliesFord F-150 - 1997-2003 :: Truck Only Starts When It Is Cool / Won't Start When Hot
I went to walmart and let the engine run for a while and shut it off. It would not start until it cools off. Now that its cool it starts fine. It just started doing it. Come to think of it i did get some gas in it.
View 2 RepliesFord F-150 - 1997-2003 :: Truck Starts And Then Immediately Stalls / Idles About 3 - 4k RPMs
If I don't keep in the throttle immediately after start up it will stall a lot of the time. It doesn't do this every time or if it sits for a while but if I drive it and then stop off at a store or something and then go to start it back up it gives me this problem. I notice it idles about 3-4k RPM's when I stop at a light or something too.
View 14 RepliesFord F-150 - 1997-2003 :: Terrible Rattling / Shaking At 70 MPH - Truck Starts Riding Very Rough
We just purchased a 2003 Ford Lightning with 114,000 miles on it. Had oil changed. Had to get floor master mufflers attached back on. Ever since then now when it gets up to 65-70 mph it starts a terrible rattling noise , almost sounds like a spark knock. Truck starts riding very rough. We have have only run premium fuel and even put in some gas treatment to see if this works, it hasn't, only getting worse. We are currently out of town and trying to make it home but don't want to cause any major damage to it. All the gauges are fine. Just the rattling and shaking...
View 7 RepliesFord - Explorer :: 1997 - Trans Feels Like In Neutral And Truck Doesn't Gain Or Maintain Speed
What may have wrong with my trans on my truck... this is what its doing, I am able to put in drive and drive it for so long then its like the truck is in neutral and doesn't gain or maintain speed. but i can turn the truck off and put it in park and restart the truck and it will go again?? that is how i got it home....
the fluid is burnt now but wasn't that bad until the trans started doing this. I have pulled off the pan and inspected the filter and it does have metal debris in it, pulling the valve body off tonight before work (work 3rd shift) to inspect that, i think it has something to do with the solenoids or valve body because it actually moves but then quits until i restart the truck. Also does the transfer case use fluid from the transmission? or are the fluids separated between the 2.
Truck has 4.0L SOHC with a 5R55E in it 4WD...
Ford 7.3L Power Stroke (1999-2003) :: Trans Not Shifting Into 1st Or 2nd / Truck Acts Like In Neutral
So I put in new clutch yesterday. Reverse works, granny works, 3,4,5 work. ZF6 manual. But when I try to go 1st or 2nd. Its as if the truck is in neutral....what should I be looking for. I bought the truck having only knowing the clutch was completely shot, was not told about this 1&2 gear issue....
Do I need to pull the trans out again... or is there something I can see or adjust, because from what i can see where the shifter connects there is no adjustments. Is it probably a gear selector fork...or connection that took a crap. when moving in granny gear i did not hear any irregular noises....
Ford Super Duty (1999-2016) :: 2003 F350 - 4x4 High Not Working / 4x4 Low Putting The Truck In Neutral
I recently bought a 2003 F350 super duty dually automatic transmission 6.0 deisel 4x4. The 4x4 is not working. with the hubs in auto when i flip the switch to 4x4 high nothing happens.The same with 4x4 low putting the truck in neutral. I can only find 2 fuses using the owners manual that says anything about 4x4 and both of them check out good. Also the owners manual says when i turn on the key I should see a 4x4 light and a low range light momentarily. Neither of these lights are showing up. I don't hear any clicking or any noise of any kind when trying the 4x4.It acts like an electrical issue but not sure where to start.
View 7 RepliesChevrolet - 2500 :: 1997 - Chugging When Truck Starts
1997 Chevy C2500 silverado... Ok, so when i go to turn my truck on she'll sit there and chug as it starts. usually a few seconds and then roars up just fine. However I've noticed a couple of distinct things. 1. when it does start i see a second or three of black exhaust come from the tail pipe. 2. if its been started recently. IE within 24 hrs it has problems. but if i leave it over a weekend then the first start has no problems. 3. Last weekend we replaced the Fuel filter and the first few starts there was significantly less problems starting but after 5 starts its back to doing it again.
I checked and the fuel pump does work, I've tried changing the fuel filter ( #2 above), and put sea foam into the gas tank hoping to clean out any gunk in the lines somewhere. It does turn on and when it does it runs great so i know its not having electrical problems as well as the alternator is charging like normal.
Im about to take it in for an oil change and see if that does anything, and I'm praying its not a clog in the Catylitic converter.
Ford F-150 - 1997-2003 :: 1999 - Chattering When Shift Down Or Just Sitting In Neutral
My truck is making this chattering when I shift down or just sitting there in neutral it goes away when I press the clutch or if I push the shifter in the spot before the gear I was told it was a throw out baring but I'm not sure I herd this transmission will start to chatter before it goes out so what to do?
1999 f150 4.6 4x4 Romeo 5speed single cab...
Ford F-150 - 1997-2003 :: High Idle In Park / Neutral And Shifting
I have a '98 F150 4.2l with 230k miles on it. A couple of days ago when starting, I noticed that the engine kept racing instead of idling down like it normally does and the weather here in Arkansas has approached the 80 degree mark. The engine also doesn't idle down when shifting (I have a manual tranny). Where to start? I don't have any codes stored other than two for bank 1 and bank 2 running lean but they popped up many miles ago. I'm thinking either a vacuum leak or throttle control. I checked the operation of the cable and the throttle valve and they appear to be fine. Maybe the idle air control?
View 4 RepliesFord F-150 - 1997-2003 :: 4R70W Shift To Neutral Between 2 - 3 Then Drop Into Gear
4R70W. This one is in my 99 F-150 with the 4.6. From what the previous owner told me this trans only has 13k miles on the rebuild and I believe him because the converter is bright blue and when it does shift right, the shifts are solid and fluid is very clean. Truck only has 98k miles on the body as well, so it's possible the truck did sit a while because my tires have a ton of tread on them, but they are dry rotted a bit (dated 2006 IIRC).
Issue: When the trans is cold (sat overnight) it will shift to neutral between the 2-3 shift for 1-3 seconds depending on outside temperature and then drop into gear. But it only does this for the first 30 seconds or so of driving, after that it shifts normal (although it does seem to hold gears a little longer than I would think it should on occasion and not upshift). I have only gotten it to do it once per cold start so it seems like once the trans gets any heat it's fine.
I was also thinking I was getting drain back and maybe it wasn't heat related so I dropped the pan, replaced the filter, fluid and pan seal (it had a small leak) and torqued the valve body. Two of the bolts were a little loose, but the rest were fine. Tightened them to spec and put it back together with no dice. Truck also gets pretty bad fuel mileage so I'm starting to think maybe there is some temp sensor screwing everything up?
Ford F-150 - 1997-2003 :: Engine Seemed To Slip Into Neutral When Speed Increased And RPMs At 2000
I am having issues with my 2003 F150 4.6L truck. It just happened today when driving home. It started fine and then when I increased the speed and the rpms went up to about 2000rpms, the engine seemed to slip into neutral. I stepped on the gas but the truck would not accelerate, it was just coasting. I pulled over to the side of the road and came to a stop, but didn't shut off the engine.
After a few seconds, I proceeded to give it some gas, and it engaged in gear and accelerated...until I got to about 25mph & rpms increased to about 2000 again. It did the same exact thing....seemed to shift back to neutral so that I could not accelerate. I had to keep pulling over to come to a stop, and then slowly proceed again. I wasn't too far from home & I made it. What this issue could be?
Ford 7.3L Power Stroke (1999-2003) :: Truck Starts And Runs For Forty Five Seconds Or So
Trucks been running perfect for 11,000 miles atleast. its last issue was a bad turbo but that was my fault. No issues whatsoever since. 10 miles down the road from work last night truck had a slight miss in between 55-60 for four or five seconds, I put the pedal down and brought it up to 75 or so just to see if it was my imagination and it felt fine so i wrote it off. It ran fine to the house we're working on i wanted to check on before I got home.
Parked it, it idled down to 650 before it came back up to 750 and it never does that and sounded different then it usually does. so i felt something was definitely up. i shut it off, was at the house about a half hour before i decided to head home, started and ran fine, three miles down the road the slight miss came back, it seemed to go away if i got on it pretty good and when i let off but just cruising with slight throttle it had the slight miss.
Got to my road where i had to slow down and turn and it idled down and died. I coasted over, unplugged the icp sensor and it cranked for 10 seconds or so and lazily came back to life. I got it home running decent and parked it. Scanned it with my old super chips tuner and it came up with a p0340 camshaft position code.
Matched my symptoms i felt so this morning i decided id go back to work and grab my spare out of my wrecked truck. truck started and idled perfect. made it to the end of my driveway before the miss came back and then it just died. took the car to work, grabbed my spare camshaft sensor and my maximus scanner, came home scanned it, no returning p0340 cam code but i swapped the camshaft sensor anyway and watched icp and ipr data, the ipr voltage is where it should be and rises while cranking while cranking.
ICP is climbing to almost 3,200 psi and it will begin to run when it peaks out. she'll fire for 45 seconds after 25 seconds of cranking or so and then it'll just die. if it sits for a few minutes it takes a few seconds of cranking before ICP will come off of 0. I've come to the conclusion that it is making high pressure oil it is just dumping it as fast as it can make it. I changed the ipr out because that can do it, it didn't change anything so I'm on to believing an injector is dumping it as fast as possible.
Is it possible for something to come undone inside the injector to make it dump high pressure oil or will a bad o ring cause this? i'm leaning towards a failing injector as when it does fire and run its definitely misfiring and i just put new o rings on them when i swapped them over from my wrecked truck but that was like 45,000 miles ago as well..
Ford 7.3L Power Stroke (1999-2003) :: Truck Starts Then Dies / Cuts Out When Running
I have changed pickup filter in tank and cleaned 2 tube filters in tank i thought that would fix it.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Starts And Runs But Throttle Doesn't Work
So I installed my chip today. It's got anti-theft, high idle, stock, 50, 75, 100 tunes.
With the chip installed the truck starts. In all tunes except "High Idle" it idles at about 1000... normally it would be like 500-600. High idle position works (1100-1200 RPM). Anti-theft position works - it kills the truck. The throttle does nothing when pressed no matter which position it is in. Stock, 50, 75 or 100.
I removed the chip and the truck runs fine. Did these guys send me one for an automatic? Or do I have the wrong computer in my truck? My computer code is DAC3 and the truck is a 2000 with a manual transmission.
Ford F-150 - 1997-2003 :: Starts But Not Idle?
So, I don't use my F150 too much and an animal made a nest int the intake tract and the nest material (chewed up air filter) got sucked in the throttle body all the way to IAC valve. So I thought I cleaned everything out, even got a new IAC. It starts now but just dies. I didn't remove the throttle body, should I? Where else do you think I could I find this stuff?
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Starts Great And Dies When Hot - Codes P1283 And P1212
Truck starts great, and runs and idles fine until it warms up. This could be 15-20 minutes of driving or idling. Then it just dies. Like dead dies, lose power steering, everything (ac and lights still work, but no engine). It had died while idling, it has dies while cruising at 45mph. Then it will crank but no start. After about a 45min to an hour it will start like there was not issue, and pretty much drive the rest of the day (even after sitting) with no problem.
I installed the Adrenaline a few months ago, but the truck ran great for quite a while before this problem occurred. I did have it shipped with a rebuilt IPR. Tonight, I rebuilt the IPR with Guzzle's kit, and stripped it all the way down. Truck died again.
I have not had my AE hooked up when it died (stupid me today). But afterward I have been getting a few codes: P1283 (IPR Control Circuit) and P1212 (ICP lower than desired Engine crank or run).
When trying to start ICP duty cycle is about 64% and pressure is 185 to 190. If I unplug the ICP sensor pressure jumps to 2000ish, truck turns over faster and ICP Duty cycle goes to about 35%.
Ford F-150 - 1997-2003 :: 2002 - Starts Then Dies?
Truck starts right up. Will die if I dont give it some gas for about 5 seconds of so. No check engine lights. I did leave the hood open yesterday adn the auto sprinklers came on. I completely forgot about it. I check the air filter before I started it and its dry so I dont feel its water intrusion. I shot a quick burst of carb cleaner in the IAC and then reinstalled it. No joy. When running it will idle and runs fine. If I unplug the IAC it stumbles and almost dies. Any way to test the IAc, TPS or MAF sensor ? I hate just throwing parts at them without diagnosing them properly.
View 14 Replies