Prius Plug-in 2012-15 :: Rear Window On Driver Side Blown Out While Driving On Smooth Road
I am driving along on Interstate 26, smooth road, no weather going on, clear night, about 7:30 pm, and the rear window on the driver's side just exploded.
Oblong hole in window, rest like a spider web. All fell out as I drove home.
Nothing hit it, had not been raised or lowered for hours, there is NO reason that I know for it to have happened. Bought car in March, 2012. 12,000 miles on it. NO other damage to car, inside or out.
Ford F-150 - 1997-2003 :: 2001 4.6L V8 - Spark Plug Blown From Cylinder 3
My son has a 2001 F150 with a 4.6L V8 that's blown a sparkplug from # 3 cylinder. The plug looks as if struck by lightning and has a burn groove as deep as a kitchen match stem the full length of the threads.
How difficult is an engine swap/change using another 4.6L? Neither of us have extensive mechanical backgrounds but plenty of aptitude.
Ford F-150 - 1997-2003 :: Truck Won't Start After Blown Spark Plug Repair
Last weekend my number 4 spark plug blew out while on the highway. The truck stayed on long enough for me to get off the highway and pull over before it died. I towed the truck home. Last night I repaired it with a helicoil and replace the spark plug and coil. Now the truck cranks but won't start. I noticed that my theft light flashes fast and doesn't stop after a few seconds or during cranking. I still haven't tested relays or fuses because it was late after the repair. I will be checking those tonight.
I will be reading and taking suggestions and posting my results tonight while I'm working on the truck. I will be checking the fuel pump and PCM relay tonight. I will also try 2 different keys and checking the Inertia switch on the fuel pump to see if that tripped. The truck is a 2001 F-150 Lariat Supercrew with 150k miles on it. 5.4 liter engine.
Ford F-150 - 1997-2003 :: Fuse For Driver Side Power Seat Blown
I don't know what to try next. I have a short somewhere, just don't know how to track it down. I checked the fuse for the drivers seat and it was blown. I stuck a new one in and the thing blew as soon as I stuck it in. I disconnected the seat motors, plugged in a fuse and it blew again as soon as I stuck it in. How to track this down?
I don't see any worn or shorted wires under the seat. I checked under the passenger side kick panel per another post I found, but that looks fine. I don't know where to look or what to test.
Camry :: 2003 4cyl LE - Cold Air Blown On Passenger Side While Heat Is On
My 03 Camry is blowing cold air on the passenger side while the heat is on. The drivers side blows hot air as it should. The coolant is full. Its a 4cyl LE and does not have dual climate control.
View 14 RepliesFord F-150 - 1997-2003 :: Truck Is Misfiring / Blown Head Gasket Cylinder 6 On Driver Side
Ok I got this truck from my mother-in-law for free with a blown head gasket cylinder 6 driver side. I did the replacement had the heads machined put it all back together by the book. Now I can't get it to fire on all 6 cylinders only 5 I think. Thought maybe bad gas (it sat since late November) put 5 gallons (over double the gas) fresh gas and half a bottle of b-12 chem tool. Dubble checked all plugs wires connections (coils plugs wires all new). I drove for about 10 miles oil pressure and temperature stayed perfect but no change in running truck shakes a lot and no real power. Don't sputter or backfire no engine codes other than imcr bank 2 open. Engine is 4.2l v-6 170k miles.
View 2 RepliesFord F-150 - 1997-2003 :: Missing / Died On The Side Of Road And Have No Spark?
I recently purchased a 1997 F150 4.2 Liter. On the way home it started missing. Within the next few days it died on the side of the road. After towing home I found no spark. A few days later I t started but only for a few minuites and died. No spark, coil pack is new so I replaced the CKP and it started up. Drove it about 1/2 Mile and died again, No spark again. Not getting power to coil pack when I am turning it over. So in short, new coil pack and CKP sensor and no spark. If it sits for a few days it may start or it may not. But if it does it only runs for a short period and then no spark again.
View 3 RepliesFord Super Duty (1999-2016) :: 1997 F250 XLT Spark Plug Chamber 2 Blown Out
The spark plug in chamber 2 blew off while the vehicle was in motion (approx 35 mph). Purchased replacement plugs and when I went to install, there was nothing for the plug to grab (i.e. appears that all of the threads on the block/casing are gone . Not sure what my options are.
View 2 RepliesFord F-150 - 1997-2003 :: Passenger Side Headlight Is Very Dim
I have a 2000 Ford F150 4x4 extended cab the passenger side head light is very dim try and turn on high beams and it does not react while on low beam the high beam indicator in the cab is on. Where can I look or what is the common problem for this.
View 10 RepliesFord F-150 - 1997-2003 :: Grinding Noise On Passenger Side
I'm trying to find out why my truck has a grinding noise on the passenger side when my truck first starts driving for the first 1/4 mile. It stops after that or when I apply the brakes. Do I have a brake sticking or something more serious?
View 1 RepliesFord F-150 - 1997-2003 :: Passenger Side Exhaust Manifold Cracked
2003 F150 5.4 4x4 supercrew ,76k miles
Recently the passenger side exhaust manifold cracked on my truck. I bought this truck about two years ago with 58k on it and currently have 76k miles. I remember getting the carfax report and being relieved to see that it had exhaust manifold replaced in July of 2014 at 49K miles along with a new EGR tube. I called the shop that worked on the truck to see if he could confirm that both manifolds were replaced since carfax only said manifold & egr tube. The shop manager confirmed that both manifolds were replaced and he told me that they were most likely manifolds from napa according to the part number.
Now, my question is, what's the best brand to replace the manifolds with? Should I just go with OEM and spend the extra $130 per side? I know the manifolds are a common problem with these trucks but only lasting three years and 27K miles just seems ridiculous to me.
I'm hoping that when I get around to actually doing this that they wont be to bad because of how recently they were replaced. For now I just cleaned the area with a wire wheel and used the inferno metal repair. Seems to have done the job but I don't expect it to last long, just another month or two until I move to a place where I can actually work on my vehicles.
Ford F-150 - 1997-2003 :: Oil Leak / Dripping Off The Frame On Passenger Side
2002 F150 FX4 w/ 5.4 Just sprung a new oil leak somewhere and I can't tell where it's coming from. The oil is actually dripping off the frame on the passenger side. It looks like the leak is somewhere at the back of the engine on the passenger side above the bell housing. It's dripping on the frame and running down a little ways before dripping to the ground. I can't get a good visual without removing the inner fenders. It's a pretty good leak that just started yesterday. Not a drop before then. I just had the oil changed within the last couple of days if that works.
View 3 RepliesFord F-150 - 1997-2003 :: 2000 - Oil Leak Under The Frame On Passenger Side
I have a possible oil leak as the title said and it's a 5.4 triton. I believe I'm seeing oil under the frame on the passenger side. Where the leak is coming from and I know it's not a severe leak it's still concerning and what it could be. 2000 F150 Lariat 5.4 ....
View 4 RepliesFord F-150 - 1997-2003 :: Passenger Side Manifold Studs Replacement
2003 F150 4.6 - I'm currently replacing the passenger side manifold studs. How the heck do you get to the bottom bolts? Looks like the motor mount is in the way. There's way more room on the 5.4s...
View 4 RepliesFord F-150 - 1997-2003 :: 2001 - Passenger Side Window Won't Roll Up?
I just purchased a 2001 F-150 XLT and while driving it back to town my brother rolled down the window and now it wont go back up! The drivers side works fine, but the passenger side wont roll up using either side of the switches. I know it isnt the motor because neither side would work. What it might be or how I could fix it?
View 5 RepliesFord F-150 - 1997-2003 :: Bad Rattle Developed Inside The Passenger Side Door
I have a 2002 F150 Lariat Supercrew, and suddenly a bad rattle developed inside the passenger side door. The window still works fine, but I'm afraid it won't much longer. I have taken the panel off, and can reach into one of the supports and mimic the rattle. When you shut the door, it sounds like the glass is going to fall out. I had to replace the motor on the driver's side door a couple of years ago, and I'm hoping to prevent another window sliding down inside the door. How to fix this situation? I haven't been able to feel anything that may have come loose.
View 3 RepliesFord F-150 - 1997-2003 :: 2001 - Rattle Noise From Passenger Side Of Engine
I'm wondering what is going on with my 2001 F-150's 5.4L Triton engine. Recently it's been making this noise that I can best describe as a "rattle" from the passenger side of the engine. It's not a constant rattle, it comes and goes every few seconds.
It sounds like it's either from the valve cover or timing cover, so I was thinking maybe it's the feared Cam Phaser failure, however the noise doesn't seem to match what I've heard from other videos of confirmed Cam Phaser failures.
I've attached a link to a video of the noise that I made. It also has a lifter tap from the opposite side of the engine that may be noticeable in the video. It has been present since I bought the truck two years ago, it hasn't gotten any worse and it isn't what I'm concerned about.
Video link : [URL] ....
Ford F-150 - 1997-2003 :: Head Gasket On Passenger Side Number 3 Is Leaking
I have a 97 with a 4.6 Triton motor I need to replace the head gasket on the passenger side number 3 is leaking nothing else is wrong with motor so I have it torn down to timing chain cover and ready to remove. do i have to take the drivers side valve cover completely off to take timing chain cover off or can I take to first 2 studs out of the drivers side front valve cover and side the timing cover off. I just want to replace the passenger side head gasket and get rid of truck.
View 6 RepliesFord F-150 - 1997-2003 :: Replacing Passenger Side Front Oxygen Sensor?
At least this is how I did it after a P0133 code.
The back ground on my truck (see sig) is that I am the second owner (my former neighbor was the first) and it has 293K miles on it at the time of this post. The truck is bone stock FWIW.
I searched the internet and couldn't find a good step by step replacement write up. The front oxygen sensor on the passenger side is hard to get to so here is what I did:
Jacked the truck up and placed jack stands under it. Removed the front passenger tire and the plastic wheel well liner.
Tools needed for this part are a 7/32 socket and a trim tool remover (for the plastic push in fittings).
There are 5 screws and 3 or 4 plastic push retainers (don't know actual term) to remove.
Because of the location of the sensor I had to remove the transmission dipstick tube. *If you do this have a pan or bucket under this area as you are going to lose fluid* the dipstick tube is held place by an 8mm bolt about the middle of the exhaust manifold. Unscrew it and with a little pressure the tube will pop up and out, and so will some fluid.
Wheel well liner out and dipstick tube pulled out of the way.
The connector where you will disconnect the old 02 sensor is tucked up behind the engine block and is kind of hard to get to. A little time and patience and you can get it separated.
From underneath the truck I cut the end off of the old 02 sensor (because the closed end of the wrench wouldn't fit over it) and used a 7/8 box wrench to unloosen the sensor a little at a time until I could get it out with my fingers.
I put the new 02 sensor in finger tight and then tightened it down with small turns of the 7/8 wrench until tight
The cord on the new sensor is longer than the factory one so once reconnected I used zip ties to keep the slack up and away from the hot parts.
New 02 sensor installed and dip stick tube back in place. Note the attachment approx 1/2 down the dipstick tube. It is the 8mm bolt I previously mentioned.
Wheel well back in place. Truck lowered back to the ground.