Ford F-150 - 1997-2003 :: Knocking On Start Up And Acceleration
I have a 2001 F150 4x4 5.4l with 105k miles. I started it up today to go to lunch and it made a knocking sound on start up that lasted maybe 20 seconds. So i shut it off and checked oil. All ok. Started it up again and it knocked but not as long as it did previously. I started to drive and higher in the rpm range before the trans shifts it makes the same knocking sound. Left off the pedal it goes away then rev it again it doesn't make the knock till around 2000rpm mark it I remember correctly. It makes the noise in all gears, parked or driving. It runs great, no power loss or misfire. Could it be a spark plug on the verge of blowing out or is it time for a new motor? I am going to look at it more tonight when I get off work.
View 2 RepliesFord F-150 - 1997-2003 :: Start And Idle For 2 Seconds Then Knocking Sound And Die
I have a 97 7.3 ... I've had it about 2 months now and now it wont start! It will start and idle for 2 seconds then start knocking and die! I had a buzz test ran on it and all is good. I also checked my Icp and checked my uvch harness with my multimeter. Before this it would run ok but seemed like it had a miss and a lack of power. On start up if i didn't have it plugged in it would smoke white smoke horribly. I am thinking maybe my IDM. I need my truck for work .... I had it hooked up to a scanner and it said faulty IDM.
View 1 RepliesFord F-150 - 1997-2003 :: Over Revving At Cold Start?
Winds way up with a whine for the immediate 2-3 seconds after a cold start only and settles down as normal. Disturbing new sound and action that just started in the last day or two. 216k on the clock.
View 4 RepliesFord F-150 - 1997-2003 :: Random Delayed Start When Truck Is Cold
Not all the time, but I've noticed it after the truck has been driven - shut off - then started again within a few min period. When truck is cold or has been sitting for an extended it starts no problem. By "delayed" I mean once I try to start the truck it takes a sec or two longer than normal before it cranks. Then when it does start it will idle very low for a sec or two then pick up and act normal.
So far I've done this to remedy it:
- new fuel filter
- new air filter
- cleaned MAF sensor
- cleaned throttle body
- seafoam thru vac hose
Only thing else I suspect is weak fuel pump but looks like it was act up all the time not just when the truck is started back to back. Truck has good power when running, I did a couple short blasts up to 80mph and everything was fine.
Ford F-150 - 1997-2003 :: Clicking Noise When Truck Start Cold
Start truck cold, getting clicking noise...sounds like valve but runs great. Warms up and clicking goes away. Remove #1 spark plug and it shows build up of whitish carbon. Will remove the other spark plugs and check. Also starting to use half a can of oil a week. No leaks that I can see. Oil pressure gauge shows high...always has. Also, open door and get out after driving and smell oil. Wanted to make it to 400k but might not be able to with this issue.
Going to do a compression check to see what else is happening. Still have decent power. If cylinder pressure is good would it make since to do just a "top end" rebuild (if it is a valve issue? Should i pull it and do a complete rebuild? What does white build up on spark plug usually indicate?
Ford F-150 - 1997-2003 :: Hard To Start In Cold / Cranks Fine But Does Not Want To Fire
My girlfriend has a 2003 f150 4.6lt pick up its a great truck most of the time. Problem is when the temp gets in the neg double digits it becomes very hard to start it cranks fine but doesnt want to fire. When it does fire it might stall a few times before it stays running. The last cold snap we had I replaced the battery and in the summer the starter got changed. I have heard that this model of truck are known for hard cold starts. I am just wondering if this is true and any other thing besides block heater. It is strange that my 89 gm pickup will start no matter what temp and I'm having problems with the newer truck.
View 1 RepliesFord F-150 (2004-2008) :: Very Loud Knocking Noise On Cold Start Up
5.4. So I have a 2004 F-150 that just passed 80,000 miles and a month ago it started making a very loud noise on startup, but only cold startup, meaning if I haven't used the truck in about three hours. Now I went on youtube to research and found a video of a truck making the exact same noise! Here is the link:
2004 f150 cold start knocking noise - YouTube ....
Need to verify what this is??? Some people are saying cam phasers and some are saying I'll need a brand new engine!
Ford F-150 - 1997-2003 :: Knocking After Get Up To Speed And Let Off The Gas A Bit
My 2000 F150 started knocking, it does this after I get up to speed and let off the gas a bit, it will know as I push on the gas again but if I push heavy on the gas it dose not knock, What could if be? By the way it is a hard knock not a pinging sound.
View 3 RepliesFord F-150 - 1997-2003 :: 1999 4x4 5.4L - Started Knocking?
The other day I was driving down the freeway... My F150's heart started knocking... I am thinking of rebuilding it or I was thinking if I can find a good priced lightning 5.4 going with a swap.. If I did go with a swap what all would I need from the donor truck? I am guessing a rebuild would cost me around $2000.. Since I don't have the know how or the place to tempt it on my own.
View 3 RepliesFord F-150 - 1997-2003 :: Knocking Sound Coming From The Top Of Engine
New to owing a ford pickup. I bought a 2002 Ford F-150 lariat 4x4 as a project truck. I've always wanted a truck to mess around with, but once I got the truck home I noticed it had a knocking sound. It didn't sound like it came from the top of the engine so I checked the muffler first and found it had a 3" slit in it. I replaced it but the sound remains. I heard it could be lifters? Is that something I should mess with or not?
View 8 RepliesFord F-150 - 1997-2003 :: Knocking At Startup / Screech On Acceleration
I am going to start from the beginning because oftens times we don't provide all of the information that may be pertinent to the correct diagnosis or repair. It'll be kind of lengthy! It all started about 3 days ago when my wife told me that my truck was "shaking." I said, "ok, just drive the car til' I can look at it" The next morning, the I was able to look at the truck. I had a cylinder 8 misfire detected. I drove it for about 1 hour that day to and from work. I did this so I could see what what the "shaking" was. It was actually what I describe as a "shudder."
Anyways, I done a fuel pressure check and all was well. I took of the coil, tested it, it was fine. So, I took out the plug to inspect it. It was wet! Not drinched, just mildly damp. I dried it off, cleaned it off with carb cleaner and it fired right up no hesitation no nothing. No CEL light, no shaking, no shuddering. It ran perfectly normal. I let it warm up to speed and took it for a test drive around about 6 city blocks. All was well. So I took it on the highway for about a 2 mile stretch. I was givin' her some juice pretty hard to see if it would misfire. Upon acceleration I heard a screech. Now this is where it get's interesting.
The screech that I hear, I just related it to the belt because it's done it ALL the time. When I first bought the truck it squalled like a whipped puppy cause of a cheap belt. The good ol' bar of soap trick fixed that! But, ever since then, it upon shifting, or under acceleration it would screech then stop. So anyways, on the highway run, it screeched while I was accelerating. It did this from about 60mph-80mph. I then, turned around and came back home. By the time I got to the stoplight to turn off towards my house my oil light was on and the engine was knocking. Not a tap, a knock.
I slowly coasted home not going over 20mph and pulling it out of drive as much as I could. I get home, and I check the oil and there is nothing on the dipstick! WTF!? I always run Mobil1 Full synthetic and put it 6qts. It doesn't smoke, doesn't leak or nothing! So I freaked out and went and bought 2 qts of Valvoline Hi-Mi and poured it in. It brought up the hash marks and quieted the deep knock. Later that night after work, I done a full oil change and flush and put back in my Mobil1 Fully synthetic 5w20. It now knocks at startup, and smooths out to a tic. Then at idle, it sounds like a light knock. It appears that it goes away upon acceleration.
Ford F-150 - 1997-2003 :: 2000 5.4L - Intermittent Engine Knocking Underneath
The knocking started very suddenly 2 days ago - but not after any unusual events, other work etc. Truck has 145 K, and otherwise starts & runs perfectly. Doesn't use oil.
I heard it from in the cab, windows closed. At first, thought it may be a rod bearing - but if so, not terribly loud. Didn't drive it any more after getting home. But starting it in the drive, the knocking was audible.
Then I discovered it * completely disappeared * several times, after shutting off engine, then restart a few seconds later. When that happens, absolutely no knocking at idle or reeving it up a bit. But it may return on the next 1 or 2 restarts, then disappear again.
Since the knocking * completely stopped * on some restarts, does that rule out a bad rod or main bearing?
I haven't seen oil gauge pressure fluctuation, whether it's knocking or not. The gauge is where it's always been - well above 1/2 way. But, the gauge also doesn't move when I rev it to around 2000 RPM (? may be normal not to move, after engine's already running?). When the knocking is happening, increasing RPMs also increases the knocking frequency.
Can't hear the knocking from top side of engine w/ hood open - even using rubber hose to my ear & moving it around. But (when) it knocks, can easily hear it inside the cab or under the truck.
From underneath, knocking is more in the center of truck, near the back of block / oil pan or tranny bell housing. I can't isolate the noise as more on one side of the block than the other.
Could the oil pump itself be making a knocking noise? The knocking is "similar to" a rod knocking, but doesn't seem quite as "hammer on metal" metallic.
There are no DTCs showing on my scanner. Only odd thing was, for "O2 Monitor Test," it showed "vehicle did not return data for any O2 monitor test." Though under the scanner "I/M Monitors," it shows O2 Sens Mon. "OK," and O2 Sens Htr "OK."
Ford F-150 - 1997-2003 :: Rod Knocking Sound Coming From Bell Housing
I have a 2003 F-150 4.6 4X4. I had a knocking sound that sounded like a rod knocking but was coming from the bell housing. After some research, I found that it could be a cracked flex plate or bad torque converter. I bought and installed a new torque converter with no change. The flex plate didn't appear to have any damage but went ahead and replaced it with the same results. I actually started the engine by jumping the starter (with no transmission) and the sound was coming from the flex plate/dust cover. My question is do I need the dust cover? Or is it a bearing or something else inside the engine causing the flex plate to hit the dust cover?
View 3 RepliesFord F-150 - 1997-2003 :: Knocking And Vibrating - Gas / Throttle Pedal Noise
2001 F-150 4.2L automatic, 189k mikes. Gas pedal would do weird knocking/vibrating. It would do it at idle & under acceleration. Gas pedal would knock & sometimes slightly move or kick back at you. Felt like someone was lightly hitting it with a small hammer. Well there is not much to the gas pedal assembly; pedal, throttle cable & mounting bolts/plate. Looking under hood, a bracket from drivers side of motor was pushing back against firewall, which was pushing into gas pedal mounting bolts. I grabbed the bracket & it came off motor. Nothing else attached to bracket. Looks like it rusted off and was pinned between motor & firewall. Well, this fixed the gas pedal problems. But now i wonder what the bracket is & whats it suppose to hold??
View 3 RepliesFord F-150 - 1997-2003 :: Oil Light Came On Made A Knocking Noise And Shut Off
I have had a noise in the front of the engine of my 2002 f150 4.6 for about 2 weeks. On my way home my oil light came on made a knocking noise and shut off. The engine would not start back starter would engage but not turn motor it was seized. i called a tow truck and had it towed home. The next day just out of curiosity I tried to start it. It fired up ran and built oil pressure. If the oil pump froze will that make it . Can the oil pump make the engine act seized up?
View 3 RepliesPrius C :: 2015 - Cold Start With Vicious Knocking
Last night I experienced a somewhat troubling event. My C had a horrendous knocking on a cold start @40 Fahrenheit or so. Shook the whole car. It lasted about 3-5 seconds, and ran perfectly afterwards, even making another cold start later on @30 without issue.
How worried should I be, and what's my recommended course of action?
2015 Prius C TWO, not II as uppercase roman numerals were used for model year 2010 Prius, w/5616 miles
Sonata NF (2006-10) :: Knocking Sound On Cold Start
2005(its NF model) Sonata 2.4 petrol manual. 75000 miles. On cold start makes knocking sound( sound like Diesel). After coupe of minutes when warms up the knocking sound gone.
Also when i start driving( still on cold engine) i hear that sound only when i let go from gas pedal and only in range of 1800-1500 rpm. When i accelerate i don't hear that knocking sound.
I think is not belt tensioner because sound is much longer than couple of sec.
Ford F-150 - 1997-2003 :: 2001 - Occasional Knocking Noise Coming From Engine
I have a 2001 F150 4x4 4.6L Auto trans. 96,000 miles... I purchased it in Jan with 93,000. About a month ago it started making and occasional knocking noise coming from the engine, this noise was heard at idle in park and in drive. when I revved the motor it would go away but as the idle settle back down you could hear it again. the noise would go away as I was driving and come back with no rhyme or reason, I put a stethoscope on the engine and it seemed loudest under the oil pan. The oil gauge is up between 5/8 to 3/4. Fast forward to now, When I start it I hear a scraping almost grinding noise that resonated thru the cab it has the same intermittent characteristics. I think I am going to remove the serp belt, remove the trans inspection cover next and see what happens. Oh I did put a scan too on it, no codes but did notice 1 long term 02 sensor trim was staying around -.618 if I remember.
View 11 RepliesSonata NF (2006-10) :: High Rpm Cold Start / Engine Is Knocking
Recently, our 2009 Sonata jumps to relatively high and not normal RPM when start cold (and I don't mean winter-cold; I mean first start in the morning). It jumps to around 2500 rpm for 3-4 seconds before it goes down to the normal 1200-1300 or so for a cold start.
Also, not sure if this is the normal Sonata engine sound, but when we push the accelerator it sounds like the engine is knocking, almost like a whistle of fuel flowing.