Ford F-150 - 1997-2003 :: 1999 - Stalls / Won't Start When Hot
1999 F150. The truck is a 4X4 supercab, with the 4.6 motor, 141,000 mi. During cold weather it runs great, but as soon as the temp gets into the upper 70's or higher I have a recurring problem. The truck starts right up and runs well, but when it is shut off it will not restart until it has sat for over an hour. It has also stalled at speed on the freeway when the outside temp was in the upper 90's to low 100's.
So far it has always restarted after sitting for awhile. I took it to the dealer and they kept it for 3 days, but could not duplicate the problem and found no codes in the computer. I replaced both coils, but it is still not starting after shut down when hot. My next thought is to change the PCM, but that is a big chunk of change to be guessing about.
Ford 7.3L Power Stroke (1999-2003) :: Cranks / No Start Sometimes Stalls At Idle
1999 7.3l 6spd standard 4x4. Just bought the truck 4 months ago knowing it had a problem that once warm occasionally would t start. Happened a few times every week or two. But wait 15 minutes and the truck would fire back up. Then it started happening more often throughout a day. And I would have to wait longer for it to cool to start it up.
Icp has been changed
Cam sensor
Pulled valve covers to check to see if there were any injector o rings failing. They were all good. Put it all back together.
Pulled the IPR and tore it apart cleaned it all out
Started driving it ran great for a week. Then today sitting at a light the truck died just as if I had turned the key off. Wouldn't start for 3 hours. The. Fired up. Took it to buddies show and started checking things out again. Both batteries load test great and fully charged. Alternator pumping out 13.5 and up.
Codes i have pulled are waste gate to high /low
I forget the number for that one. The second was P1211. Cps has been changed and ipr cleaned. Think that I should replace the ipr of this happens again?
I did get w code a few weeks ago about low voltage at module. this code doesn't appear anymore. Since I checked the plug ins all looks good. But the PCM wasn't mounted properly. So I fixed that up and checked battery connections. They were very good so I re did all of that.
Anyway. Back to the problem. After ipr clean. Drove as she should until sitting at a light a week later. Truck just quit. Would t start back up until cold. Any thoughts. New IPR? Oil in hpop within half inch from top. And I don't seem to have any oil leaks. Did oil change fuel and air filter. Not low on any fluids. I had a 1997 too and threw a bunch of cash at it like this one trying to find the issues.
Ford F-150 - 1997-2003 :: Stalls At Idle - No Codes
My buds 2003 4.6 liter stalls every time he takes his foot off the pedal. Runs fine otherwise, no roughness or anything, you just have to keep your foot on the thing to keep it from dying out.
We checked for codes and found none. I checked vacuum connections and they looked OK.
Is there an easy way to test the IAC or should we just throw a new one in and cross our fingers? If we do change it out, does the truck need to be driven around a bit for the computer to re-learn anything?
Ford F-150 - 1997-2003 :: Stalls Out At Idle After Manifold Replacement
I have a 97 ford f150 with a 5.4 I bought the truck with 114000 miles on it and the exhaust manifold bolts were broke from the exhaust I have replace the whole manifold with new gaskets and bolts and I get the codes 1131 and 1151 which indicates o2 sensors indicate lean and I also get p0136 and p0153 which indicate lean or front o2 sensors it will stay running for a little bit every once in a while but it only idles at 200 to 400 rpms and I'm not sure what to do?
View 4 RepliesFord F-150 - 1997-2003 :: Idle Down To The Point Where It Almost Stalls When Stop Or Park
2001 f150 supercrew 5.4 triton... Recently did a tune up plugs,coil packs,filters,belt the whole 9 yards. The truck starts fine accelerates great and cruises down the road great without missing a beat.
But every now and then when you stop at a light or park it begins to idle down to the point where it almost stalls. When it does this i usually stab the throttle and it revs right up without missing a beat and idles fine for a a while then same thing all over again.
Could this be the idle air control? Seems like something simple due to the fact it runs down the road and accelerates like a big dog.
Ford F-150 - 1997-2003 :: 1998 V6 - Loping At Idle / Almost Stalls While In Gear
I have a 98 F150, 4.2 V-6, 183,000 miles.. Lately, she's been loping at idle. Especially while in gear... almost stalls. Once revved up, everything seems normal. Still goes up hills fine if I get on the gas. The light was on, and I got codes for lean condition on both banks.. (P0174, P0175).
I already cleaned all the sensors in front of the intake.
The MAF was real dirty, and the IAC was full of soot too.
They both cleaned up nicely, but it didn't work.
I borrowed a fuel pressure gauge yesterday, and it showed 12 psi with the "key on, engine off".
It showed 29-30 @ idle, and only went up to 35 when I revved it a little.
The guy at the store said the range is supposed to be "30-45 psi with the ignition on", but I'm not sure if that means engine running or not..?
Either way, it looks like the pressure is on the low side, so I'm going to change the fuel filter next (and hope for the best).
If the fuel filter doesn't fix it, what should I go after next? And, is there a way to test the fuel pressure regulator before buying a new one?
Ford F-150 - 1997-2003 :: 1999 4.2L - Hot Start Rough Idle / Surges Sometimes
I am new to FTE and have a question about my 99 4.2l. After it warms up, i can shut it off and about 30 mins later try to start it again and it will idle very rough and sometimes stall. I also noticed that it surges sometimes with just off idle throttle when its cold. I am not getting any codes thrown, here's what I've done so far: cleaned the maf and throttle body, and it didnt work at all. I did convert my cht over to ect by using the plugged coolant outlet on the lower right side of the intake manifold and extending the connector wires which actually solved the problem a little bit but it still does it from time to time.
More info about the cht to ect conversion, but after reading that ford did away with them in later models i wanted to do the same while at the same time making it so much easier to swap it out if ever needed. No more getting under the truck. And where im at cht's are kind of hard to come by without having to order them Anyway, it worked flawlessly! I only had to extend the wires by about 8", wrapped them and ran it along side the injectors for a clean factory look. Ill try to post pics soon...
Ford F-150 - 1997-2003 :: Stalls / Stutters - Cranks But Won't Start
So I leave town Friday with the wife's car for a golf tournament that is 4 hours away. I left her with my 2001 F150 Supercrew Lariat 4x4 5.4L. She calls as I am starting my practice round on Friday stating that the truck had died on her in the local Dillons parking lot. She had driven to the east side of Wichita, then drove all the way back to the west side before swinging into Dillons to get some chinese food for lunch. When she gets in the truck to leave, she starts it and it runs rough.
She gave it gas and it ran fine for a few seconds, she put it in drive, and then it started running rough again. She stopped the truck in the parking stall ahead of her, turned it off, and restarted it. Same thing...runs rough. She tried giving it gas, but it would not go above 1500 rpm. Then it just died on her. She then tried cranking it, but it would not turn over. She let it sit overnight and got a ride from a friend (it was 102 degrees out), went back the next morning to try again. Same thing, just cranks. So I get back last night and go up with my scanner. No codes, no SES/CEL.
So, I am now thinking it is the fuel pump. I crawled underneath the truck and had her turn the key so I could see if I can hear the fuel pump. Nothing. I went ahead and disconnected the battery to let it sit overnight.
I am about to head up there and see what I can do. So far, here is my list of things I need to check:
1. Fuel pump relay #301
2. Fuel pump fuse #18
3. Check for the theft light
4. Check "inertia switch" on the passenger side kick panel
5. OPEN gas cap and listen for the fuel pump (had never heard of that one)
6. Hit the gas tank a few times with a rubber mallet to "jar" the fuel pump (again, never heard of that one).
My question to all of you is: Am I missing anything else? Alos, with it running perfect, then running rough and suddenly dying, would is necessarily be the fuel pump? I had read something about a "Fuel Pump Module" located near the spare tire. Is that something I should check into with it running rough (well, not running at all now) like this?
Ford 7.3L Power Stroke (1999-2003) :: Rough Idle - Stalls Out?
Truck has a rough idle and finally just stalls out. I replace the under valve cover wiring harness and put in new glow plugs. With valve covers still off I started the truck in the issue still persist. I went ahead and unplugged each injector and each time the motor had a hick up .
What am I pulling apart and replacing next?
Ford Super Duty (1999-2016) :: Intermittent Stalls At Idle And Hard Start
As a follow up to my problem of intermittent stall and hard start, it is getting more pronounced. Now, every once in a while, it will start. Mostly it will not start.
This morning I connected an OBD2 meter with the key on and engine off. It told me that there are no DTC's. As I was attempting to run enhanced DTC's the code reader lost link with the computer. The connection icon was on but it lost the link. At one point, after several tries, I got the link back but it didn't last too long before it was lost again.
This is the same symptom that I have with running the engine. It will run and then shut off. After a hard start, it will start and run just fine and then shut off again.
My question is this. Can I still have power to the PCM and loose power to the processor? Is there a fuse or relay that could be causing this problem? If not, could the problem be a faulty PCM.
Ford Super Duty (1999-2016) :: Engine Will Start And Idle But Bogs Down And Stalls If Give It Gas
1999 Ford Triton V-10 engine, after changing Oxygen sensors, all vacuum hoses and Mass airflow sensor,(also replaced another sensor but can't think of the name of it right now) now I don't get the codes but engine will start and idle but if I give the engine gas it bogs down and stalls. Vehicle sat in my driveway for 3 months, I got it started and drove it once about 30 miles filled up my gas tank thinking gas could be stale, but now it will not run.
View 5 RepliesFord Super Duty (1999-2016) :: 2003 F350 - Engine Stalls At Idle
I recently purchased this 2003 F350 DRW with the 7.3L, automatic trans. Truck has 140k on it. Three times now while the truck has been idling, the engine just died. The first time was a couple of weeks ago when I was pulling out of the driveway. Then again yesterday twice, once while just sitting at a stop sign. Each time it has started right up and ran fine.What is going on here?
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Stalls Randomly And Sometimes Will Not Start
2001 Excursion 7.3 - stalls randomly, sometimes will not start. After the IPR was replaced it was rough for about 4 miles (I thought maybe air in the system), next 40 miles was flawless with 3 stops and restarts. Then it sat for a few hours and I went to leave again and the problem was off and on again for another 5 mile drive. Now it won't start in the driveway. It will start if I disconnect the ICP but the idle is still a little rough.
I replaced the normal culprits after a lot of searching on here:
CPS - replaced with autozone part, thought maybe it was bad new so went to ford and replaced with official part from the dealer
ICP - had oil in the plug and it would idle better removed so I replaced the plug and as much wire as I could - soldered, heat shrunk, good connections - both the pigtail and sensor came from Ford dealer
IPR - replaced with part from the Ford Dealer (FYI - 1 1/8" 1/2" drive craftsman deep socket from sears fit in the ratchet and on the part).
Grounds - found somewhere that the ground on the firewall for the windshield wipers can interfere with the CPS so I pulled it, clean the connections and made sure it was tight and secure.
No check engine light now - I received a few through the process, but did not clear them and there are no codes at this time (self cleared on the 40 mile drive)
I'm thinking it may be some electrical issue/short or a fuel issue at this point, bowl is full and the filter is fairly new (few thousand miles). I haven't done the Hutch mod, but have over 1/2 a tank.
I'm trying to get this going as quick as I can so I don't want to waste too much time, but I also don't want to miss a critical troubleshooting step to take.
Below are my thoughts on the next steps.
Research and test fuel pressure
Tow it somewhere to test each injector - I only have Torque pro to read codes and engine status
If fuel delivery checks out ok, start testing wire by wire on all of the above parts.
Ford F-150 - 1997-2003 :: Rough Idle At Start Up
I just acquired a 2003 with 5.4 L. Did all new plugs and coils, cleaned MAF sensor, changed air filter, oil, transfluid and filter (obviously not related).
Upon start up and idle the truck has is rough, enough that it will vibrate the whole truck SLIGHTLY. Once in gear and warm, it smooths out and is fine. Unit the next stop and start.
Ford F-150 - 1997-2003 :: Start And Idle For 2 Seconds Then Knocking Sound And Die
I have a 97 7.3 ... I've had it about 2 months now and now it wont start! It will start and idle for 2 seconds then start knocking and die! I had a buzz test ran on it and all is good. I also checked my Icp and checked my uvch harness with my multimeter. Before this it would run ok but seemed like it had a miss and a lack of power. On start up if i didn't have it plugged in it would smoke white smoke horribly. I am thinking maybe my IDM. I need my truck for work .... I had it hooked up to a scanner and it said faulty IDM.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: After Start Up RPMs Drop - Stalls Out Then Idles Rough?
2003 7.3 excursion.. The truck starts every time revs up and idles about 3 seconds then the rpms drop and it tries to stall out catches itself then revs backup and idles rough similar to if you have got air in the fuel lines from changing the fuel filter.. About 1 in five times the truck will stall out and it starts and immediately and idles rough but the rpms and everything runs at speed and rpms don't drop again! This is a reman engine/transmission recently installed.. The mechanic who installed it was unable to figure the problem out.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Crank No Start Sometimes - Stutter / Stalls And Slow Acceleration
I have 2001 F250 7.3L 261k miles.
Over the last few months, I have noticed that my truck is taking longer & longer to start after sitting for a long time (i.e. every morning, after work, etc.) When the problem first started (3-4 months ago) it would crank for 2 seconds & nothing so I would turn it off, let the "wait to start" light go off again (depending on outside temp 10-20 seconds) & then it would crank & usually fire right over like it was new. That seemed to happen only in the morning when it was 70 degrees or colder outside but no problem after work when it was 80+ degrees.
As the weather has gotten colder, it has gotten progressively worse. A couple of weeks ago, it was in the 40s in the morning & it took a solid 8 or 9 minutes of cranking for a few seconds, then trying again before it started. Once it started it did "chuga chug" a couple of times before it smoothed out. Last week when it was 16 degrees in the morning, it wouldn't start at all. I tried for a solid 15 minutes before I gave up.
I will say that as it has gotten worse over the last couple of months, I have noticed that it's cranking w/o firing but I will hear it fire once or twice per crank before it will fire up & run. Once it starts, it runs like a champ. No studders, stalls, slow acceleration, etc. Pulls like it always has. The weirdest part about it is that once it starts & runs for 30-60 seconds, I can shut it off & it'll fire right up every time. If I get it up to full operating temperature, I can go back & start it right up 2 or 3 hours later w/o a problem.
I did notice my oil cooler is leaking pretty badly (that will be fixed this weekend) & my valley has fluid in it but it's hard to tell if it's diesel, oil or a combination of the two because my truck is setup to run on WMO (waste motor oil). I have dual tanks so the OEM tank is diesel & the auxillary tank is WMO. I have 2 mechanical fuel pressure gauges on my fuel bowl, 1 pre & 1 post fuel filter as well as an aftermarket Walbro fuel pump. The fuel pressure when running on WMO has always bounced a little bit between (65-75 psi) but the fuel pressure on diesel has always held solid at 75 psi until recently when I have noticed that it flutters a very small amount between 73-75 psi.
I have verified that the GP Relay works & was leaning towards a glow plug problem but considering it was having troubles at 70 degrees ambient temperature, I'm hesitant to think that's the true problem. I think that might just be adding to the problem. I live in the south so my truck doesn't have a block heater but I'm going to add one this weekend when I replace the oil cooler gaskets & o-rings.
I'm also going to pick up a new Android tablet today (replace my broken one) so I can use the Torque Pro app to monitor ICP, HPOP & InjPW. Finally, I had a DP Tuner chip on it & to remove that as the possible cause, I removed it & the same symptoms continued.
Ford F-150 - 1997-2003 :: Rough Idle At Start For About 30 Seconds - Cylinder 1 Misfire
2000 5.4l lariat. My cylinder 1 for 2 years has been poping p0301code and has a rough idle at start for about 30 seconds. It also has a little white smoke for that 30seconds. new cop, new spark plug, new spark plug pig tail, swapped injectors to different cylinders multiple times to change code no luck. Compression dry and wet are at 200 and all cylinders are within10%. I had a dorman intake manifold installed 4 years ago and the code came a few years after. Im thinking intake manifold gasket is bad between cylinder 1 and the heater bypass tube allowing coolant to slowly leak down into the cylinder causing my rough start. I looked through the injector hole but could not tell. With all the info I have given is there any other places or things that it could be before I do a gasket replacement or is all my tests leading to the intake manifold gasket...
View 5 RepliesFord F-150 - 1997-2003 :: 1999 - Low Idle With No Codes?
I have a 1977 f250 460 with c6. As far as I now everything is stock on the motor. The carb is a motorcraft but I cant see what model it is, there is a ID tag that I need to get the numbers off of so I can see what I have.
I don't know much about carbs so I'm trying to learn as I go, but what has me wondering about the secondaries is going up inclines. We have a canyon that is a decent grade and long, I was towing a empty flatbed trailer and with my foot all the way down could never get it above 40 mph it just felt like that was it. I have been out playing with no trailer and it feels like I can get them to open up when it down shifts, but cruising along at 55 and stomp it nothing.
I am worried about pulling our camp trailer with it and that is the main reason I got the truck with a 460. What to check?